evolur 811 Toddler Guard Rail Instruction Manual
- June 8, 2024
- evolur
Table of Contents
evolur 811 Toddler Guard Rail Instruction Manual
ASSEMBLY INSTRUCTIONS
Adult assembly required.
Small parts may present choking hazard prior to assembly.
Enclosed please find simple step-by-step instructions to help you quick assemble your product. Before you begin, we recommend that you follow the steps below
- Please read the instructions thoroughly
- Identify all parts and hardware
- You may need to provide the following tools:
- Philips Head screw driver
- Flat head screw driver
- Hammer
Do Not Use Power Drills Or Drivers
To protect your parts during assembly please please place them on a soft surface. To clean surface, use only water on a damp cloth. Do not use window cleaner or cleaning abrasive as it will scratch the surface and could damage the protective coating.
Furniture Care Instructions
Room Climate Control
Wood, when first cut contains more than 50 percent water. When it is prepared
for furniture construction it is placed in a Kiln and the moisture content is
brought down to 8 to 10 percent. Wood is porous and responds to its
environment. If the room has high humidity it will absorb it and expand and if
the humidity is low it will lose moisture and shrink.
It is important that the humidity levels in the room be controlled from extremes of too much humidity or too little. Furniture should not be placed close to air-conditioning outlets, fire places, radiators, space heaters, humidifiers or dehumidifiers. Exposure to extreme variations of temperature and humidity can damage any fine wood product.
The Ideal Environment for Fine Furniture
Fine wood furniture w ill have fewer problems when its environment is
controlled at a temperature between 65 and 75 degrees and a relative humidity
between 35 and 40 percent. Wood placed in an environment out side of those
limits can and will shrink or expand and may develop some small cracks which
are not material or structural defects.
Sticking Doors and Drawers
With the minor changes in temperature and humidity doors and drawers may swell
and be difficult to open or close. Tolerances have been built into the units
but extreme conditions may still cause sticking. This will adjust back to
normal over time but until it does consider using a dehumidifier or rub candle
wax or paraffin on the sides that stick.
Avoid Direct Sunlight
Keep the furniture out of direct sunlight. Ultraviolet rays w ill fade colors and in some cases darken them. It can also cause crazing or hair line cracks in the finish. White finishes will yellow naturally over time and exposure to direct sunlight will hasten this natural process along with some woods darkening naturally over time; this Is not considered to be a quality defect.
Proper Storage
If you need to put your furniture in storage for any period of time do not
store them in a damp basement or hot dry attic. Allow air movement around the
furniture and do not stack anything on it.
In General
- • Protect furniture surface from hot or extremely cold items.
- Use coasters under hot or cold beverages
- Do not use synthetic fabric under accessories or lamps
- Protect tops from pens, makers and crayons
- Oils from potpourri and other scented items can damage the furniture finish.
- Do not drag items across the surface of the furniture.
- Allow the surface to breath by rotating your accessories and lamps.
- Do not over polish the furniture, do it only two or three times a year. Over polishing can distort the natural finish of the product.
- Do not wax the furniture as wax build up can destroy the natural finish of the product
- When moving furniture always lift the unit. Do not push or drag It to avoid damage to legs
- Keep the furniture level so doors and drawers open and close freely.
- Clean with a damp, not wet, cloth. Use only a mild soap. Do not use abrasive cleaners.
HARDWARE AND TOOL DIAGRAM
HARWARE INCLUDED IN CRIB (BOULONS CONTENUS DANS LE LIT)
Model shown is example only. Styles may vary.
Toddler Bed Conversion
WARNING
WHEN CONVERTING THIS CRIB TO A TODDLER BED, A GUARD RAIL AND STABILIZER BAR MANUFACTURED BY ÉVOLUR INC., MUST BE USED.
In order to convert your crib to a toddler bed, you must first remove the front rail of the crib, mthen attach the guard rail using the bolts from the front rail removal.
NOTE: Make sure the mattress support is in the lowest position.
Please follow the complete instructions that come with the guard rail which is sold separately.
WARNING!
For Toddler Bed Use
- FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD
- RESULT IN SERIOUS INJURY OR DEATH FROM ENTRAPMENT OR STRANGULATION.
- DO NOT PLACE BED NEAR WINDOWS WHERE CORDS FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.
- THE MATTRESS INTENDED FOR USE ON THIS BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING THE DIMENSIONS OF 51-5/8 IN (1310 MM) IN LENGTH AND 27-1/4 IN (690 MM) IN WIDTH AND THICKNESS OF 4 IN (100 MM) OR A GREATER THICKNESS AS SPECIFIED BY THE MANUFACTURER.
- THE MINIMUM AGE OF THE INTENDED USER SHALL NOT BE LESS THAN 15 MONTHS AND THE MAXIMUM WEIGHT SHALL NOT BE GREATER THAN 50 LBS. (22.7 KG).
Follow us on
@EvolurBaby
@evolurbaby
Enter our monthly giveaway!
Simply scan the QRcode to register.