MUCAR CDE900 Pro OBD2 Scanner User Manual

: June 10, 2024
: MUCAR

CDE900 Pro OBD2 Scanner

MUCAR CDE900 Pro OBD2 Scanner User Manual-PRODUCT

Product Information

This product is subject to FCC and IC regulations and has been tested for compliance with the Specific Absorption Rate (SAR) standard. SAR is a measurement of the rate at which energy is absorbed by the body when exposed to radio frequency (RF) electromagnetic fields.

FCC Statement

This product complies with FCC regulations and has been tested for compliance with SAR standards. The SAR test distance for this product is 0mm.

IC Statement

This product complies with Industry Canada regulations and has been tested for compliance with SAR standards. The SAR test distance for this product is 0mm.

Product Usage Instructions

When using this product, it is important to maintain a safe distance between the device and your body. The SAR test distance for this product is 0mm, which means that the device should not be in direct contact with your body during use.

To ensure proper usage of this product, follow these guidelines:

Keep the device at a safe distance from your body while in use.
Avoid prolonged use of the device, as this may increase the risk of SAR exposure.
Follow all instructions provided by the manufacturer for safe and proper use of the device.

By following these guidelines, you can help to minimize your exposure to RF electromagnetic fields and ensure safe usage of this product.

Power/Screen Lock Button: Long press for 5 seconds to turn on or off.
Touch Screen: 5 inches (854*480 resolution)
Diagnostic Cable: Used to connect car OBD connector.
OK Button:Confirm button.
Selection Buttons: Up, down, left and right direction selection.
Return Button: Return to the previous step.
TYPE-C interface: Support 5V-1.2A charging voltage (please do not exceed this range)
Factory Reset Button: Restore factory settings.
TF Card Slot: Support expandable SD memory card, up to 256G. (Please purchase genuine standard SD memory card by yourself)

Technical Specifications

Display: 5 inch display
Working Environment: 0°C ~ 50°C (32°F ~ 122°F)
Storage Environment: -20°C ~ 60°C (-4°F ~ 140°F)
Working voltage: input 5V2A (2.5A max)
Supported Protocols: ISO9141, KWP2000 (ISO 14230), J1850PWM, J1850VPM and CAN OBDII protocol.

How to Use

Connect the MUCAR CDE900 PRO with your vehicle through the OBDII port. Usually, the OBD port is located under the dashboard, above the pedal on the driver’s side. The five locations shown lite the picture are common OBDII port locations.

Turn on the MUCAR CDAE900 Pro

Hold the Power button for 5 seconds to turn the MUCAR CDE900 PRO on. The tablet will start initializing and enter the following interface.

Note: Don’t connect or disconnect any test equipment with the ignition on or engine running.

Language Setting

Used to select the tool language.

Choose Time

Choose the time zone where you are in. The system will automatically configure the time according to the time zone you selected.

Connect wi-Fi

The system will automatically search all available Wi-Fi networks. You can choose the Wi-Fi needed. Tap “Next”.It will automatically jump to the Home Page.

Function Description

MUCAR CDE 900 Pro has 12 main modules, Code/Freeze Frame, Erase, Live Data Stream, 02 Sensor Test, EVAP System Test, On Board Monitor, Version info, DTC Lookup, Expand, Report, Settings.

Plug in the OBD diagnostic cable after the car is turned on, and the device will automatically scan for OBD protocols (wait while scanning).
Note: You can click “SMOG” to see the corresponding supported protocols, gray protocols are not supported, green without fault codes, red with fault codes.
Select “Code/Freeze Frame” to view fault codes and freeze pins. Select “Read DTC”, and select vehicle model to view dtc. Select “View Freeze Frames”, monitor status since DTCs cleared, view the engine’s current power system diagnostics.
Select “Erase” and click “OK” to clear the fault code.
Select “Live Data Stream” and click “OK” to view all data streams.
Select “O2 Sensor Test” and click “OK” to view the 02 Sensor data flow.
select “EVAP System Test” and click “OK” to view EVAP data streams.
Select “On Board Monitor” and click “OK” to view On Board Monitor data streams
Select “Vehicle Info”function retrieves a list of information (provided by the vehicle manufacturer) from the vehicle’s on-board computer.
Tip: This information may include: VIN (Vehicle Identification Number), CID (Calibration ID), CV (Calibration Verification Number).
Select “DTC Lookup” to query fault code analysis.
Select “Expand” allows you to purchase the reset and related model software.
Select “Report” and click “OK” to view the diagnostic record. Report view data flow reports, PDF documents generated by product diagnostic reports.
Select “Settings” to set the basic settings, there are functions such as feedback, repair info, upgrade, order, setting language, etc. Click update to upgrade models, need to expand 4 systems, demos and auto search function modules. Click on the app to enter the app application update, which can update the application app and the local firmware.

Extended Function Description

Tip: Please click “Expand” to purchase the following extensions.

Scan : The module has a demo (demonstrates the diagnostic process) and model software.
Reset: MUCAR CDE900 PRO has 28 common maintenance and reset functions (AIRFUEL, BLEED, AFS, ADBLUE, SUS, AIRBAG, BMS, BRAKE, COOLANT, DPF, EGR, ETS, GEAR, BOX, IMMO, INJEC, LANGUAGE, NOXSENSOR, ODO, OIL, SEAT, SAS, STOPSTART, SUN, TPMS, TRANSPORT, TYRE, WINDOW).
Auto Search: Automatically scan the VIN of car models and the list of car models.
History: This feature includes diagnostic logging.

Customer Service

Pull down the task bar, find the customer service icon, click on it, and then human online customer service will appear to answer the questions you encounter during the use of the product, giving you a better experience of using the product.

Settings

You can modify or add related information in this module, or make settings after the initial setting is completed.

Feedback
This module can record and establish the file of the diagnosed vehicles, including all diagnostic-related data such as diagnostic reports, and data stream records.
Repair Info
This module includes four sections:
Instruction: View Product Brochure.
Coverage List: The supported vehicles’ information.
Videos: Contains table usage tips, maintenance, and diagnostic guides.
Learning Course: Demonstrates how to operate the tool.
Update
This module allows you to update the diagnostic software & App to the latest version. A pop-up message will indicate newer software is available if you don’t update the software in the process of registration.

FAQ

Q: Why does MUCAR CDE900 Pro have no responses when it is connected to a car?
A: Check if the connection with the vehicle diagnostic socket is solid or check if the ignition switch is on,or if the tool supports the car.

Q: Why does the system stop when reading the data stream?
A: It may be caused by a slackened connector. Please turn off the scanner, firmly connect the connector,and switch it on again.

Q: Communication error with vehice ECU?
A: Please confirm the following cases:

Whether diagnostic connector is correctly connected.
Whether ignition switch is ON.

Or,send your vehicle’s year, make, model and VIN number to us using Feedback feature for timely technical assistance.

Q: Why does the screen flash when the engine ignition starts?
A: It is normal and caused by electromagnetic interference.

Q: How to upgrade the system software?
A:

Power on the tool and ensure a stable Internet connection.
Go to “Settings” -› “Update”_, “App” tap “OTA” and then tap “check version” to enter the system upgrade interface.
Complete the process by following the instructions on the screen step by step. It may take a few minutes depending on the status of your network. After the upgrade is finished the tool will automatically restart and display the main interface.

Q: How to capture the screenshot?
A: Pull down the taskbar and dick on the screenshot icon to capture the current screen, it will be saved in the Photo Album module.

Q: What should I do when it prompts that the network is unavailable?
A: Pull down the task bar, click the WIFI icon to connect to the available network.

Warranty Terms

This warranty applies only to users and distributors who purchase MUCAR CDE900 Pro products through normal procedures. Provide free warranty within one year. MUCAR warranty including electronic products for damages caused by defects in materials or workmanship. Damages to the equipment or components caused by abusing, unauthorized modification, using for non-designed purposes, operation in a manner not specified in the instructions, etc.are not covered by this warranty. The compensation for dashboard damage caused by the defect of this equipment is limited to repair or replacement. MUCAR does not bear any indirect and incidental losses. MUCAR will judge the nature of the equipment damage according to its prescribed inspection methods.

Please contact Online Customers Service via the order interface.
Service Line: 1-909-757-1959
Customer Service Email : service@mucarco.com
Official Website: www.mucarco.com

Products tutorial, videos, FAQ and coverage list are available on MUCAR official website.

FCC Statement

Changes or moditications not exoressiv approved oy the party responsible for compliance could void the users authorty to operate the ecuioment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are desined to provide reasonable protection against harmful interference in a residential installation. This equioment generates uses and can radiate radio frequency energy and. it not installed and used in accordance with the instructions. may cause harmiul interference to radio communications. However. there is no guarantee that interference wi not occur in a particular installation. If this equioment does cause harmiul interference to radio or television receotion. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the rollowing measures.

eonent or relocate the receivine antenna.
increase the separation between the equipment and receiver.
connect the equipment into an outer on a circui amferent from
- Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subiocato the followir two conditions to this dovice may not cause harmful interference, and (2) this device must accept any intortorenco recoivod. includiry intortoronco thal may cause undosirod oporation

IC Statement

This device contains iconco-exempttransmitterstrecoivers)that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference; and
This device must accept any interference, including intorterence that may cause undesired operation of the dovico The off

IC: before the certification/registration number only suniles that the industry canada technical spectications were met. This product meets the applicable Industry Canada technical specitications

FCC SAR Information Statement

Your MUCAR CDE900 Pro is a radio transmitter and receiver. It is desiones ano manu actures notto exceed the emission limits for exposure o radio frequency krleneroy setoy the rederal communications commission of the us. covemment. These limits are part o comorenensive guide ines and establish permitted evels O k- enerov tor the cenera population. The quicelines are based on standards that were develoed ov ingevendent scentric croanizations trouon periodic and thorouon evaluaton o scientic
stucies. The standards incluce a substanta sately marain desioned to assure the sarety o al persons. recardless of ace and healtn. The exposure standard @ MUCAR GUESOU Fro emo ovs a unit ot measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. ” Tests for SAR are conducted with the MUCA CDE900 Pro transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the MUCAR CDE900 Pro while operating can be well helow the maximum valle ThiS iS DecAUSe De MICAR COSSNO iS desioned to operate al mumple power levels so as to use only the power required to reach the network. In general, the closer vou are to a wireless base station antenna, the lower the power output. Before a MUCAR CDE900 Pro is available for sale to the public, it
must be ested and cenities to the sec that it coes not exceps the limit established by the govemment adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and wor on the body) as required by the FCC for each model. The highest SAR value for this MUCAR CDE900 Pro when tested for use wor on te oody. as ceschoed in this user guide, Is 0.25W/Kg (Body-worn measurements differ among MUCAR CDE900 Pro. dependina upon available accessories and FCC requirements. While tere may be ditterences between the SaR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this MUCAR CDE900 Pro with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this MUCAR CDE900 Pro is on te with the roo and can be sound under the Disolay crant section on nto:/wow.cc cov oeviccio atter searchino on FooD; ZAVARSUUPRO Additional information on Specitic Absorption Rates
ARI can be sound on the dellular relecommunications industr AssOCIatonCAweo- siteathtto www.wowcom.com. in te United States and Canada. e SAR imitor MUCAR COESUO Fro used by the public is 1.6 watts/kg (Wikg) averaged over one gran orassue. The stancard incoroorates a suostanta margin o satelv to ore additona profection for the cubic and o account for ans variatons in measurements The SAR test distance is 0mm. SED SAR information Statement YOU MUCAR COSCIO Pro is a radio transmitter ary receiver is desioned and manufactured mito exceed the emission limits far exposure to radio frequency (RF) energy set by the Innovation Science and sconomic Develonment Canaca of the Canada Govemment. These limits are part of comprenensive quidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless MUCAR CDE900 Pro employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the ISED is 1.6 W/kg. ” Tests for SAR are conducted with the MUCAR CDE900 Pro transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the MUCAR CDE900 Pro while operating can be well below the maximum value. This is because the MUCAR CDE900 Pro is designed o overate at multole power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a MUCAR CDE900 Pro is available for sale to the public, it must be tested and certified to the ISED that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and wor on the body) as required by the ISED for each model. The highest SAR value for this MUCAR CDE900 Pro when tested for use worn on the body. as described in this user guide, is 0.25 W/Kg (Body-worn measurements differ among MUCAR CDE900 Pro, depending upon available accessories and ISED requirements). While there may be differences between the SAR levels of various MUCAR CDE900 Pro and at various positions, they all meet the government requirement for safe exposure. The ISED has granted an Equipment Authorization for this MUCAR CDE900 Pro with all reported SAR levels evaluated as in compliance with the ISED RF exposure quidelines. SAR information on this MUCAR CDE900 Pro is on file with the FCC and can be found under the Display

Grant section of https://sms-sqs.ic.gc.ca/ after searching on IC:
26415.900PRO Adctional intormatión on Specific Ansoretion RATeS SAR can he lour on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com ” In the linited States and Canada the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to accOUnt for anv variations in measurements The SAR test distance is Omm.