weboost 470235 Drive Sleek Otr Installation Guide
- June 10, 2024
- Weboost
Table of Contents
- weboost 470235 Drive Sleek Otr
- Drive Sleek OTR Cell Signal Booster for Trucks
- Package Contents
- Specifications
- Installation Guide
- Safety Guidelines
- Package Contents
- Mounting
- Troubleshooting
- Safety Guidelines
- Antenna Kit Options
- Specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
weboost 470235 Drive Sleek Otr
Drive Sleek OTR Cell Signal Booster for Trucks
The Drive Sleek OTR Cell Signal Booster is a product designed to enhance cellular signal reception in trucks. This product is manufactured by Wilson Electronics, a well known brand in the mobile signal-boosting industry.
Package Contents
- Sleek Cradle
- Signal Booster
- Outside Antenna
- Mast Extensions, Power Supply, Side-Exit Adapter
- 3-Way Antenna Mount
- Antenna Spring
- Thread Lock Packets
- Cable Adapter
- Cradle Mount
Specifications
- Boosts all network signals, including 5G
- Works with all cellular devices and all mobile carriers in the USA and Canada
- Reduces dropped calls, improves voice quality, and increases data speeds
- Provides up to 23 dBm uplink power and up to 2.5 dBm downlink power
Installation Guide
To install the Drive Sleek OTR Cell Signal Booster, follow the steps below:
- Select a mounting location for the outside antenna. Ensure that it is at least 12 inches away from any other antenna and free of obstructions.
- Assemble the outside antenna by inserting the cable through the mast extension, if needed. Add thread locker to the thread points and screw into place. Screw on the side exit adapter.
- Mount the outside antenna using one of the typical mounting points provided in the user manual. Use the 3-way mount if there are no built-in mounting points in the vehicle.
- Route the antenna cable and connect it to the signal booster. Route the fixed booster cable and connect it to the cradle.
- Connect the system to power using the power supply provided.
- Insert your phone into the cradle and enjoy improved cell signal reception.
Troubleshooting
If you experience any issues with your Drive Sleek OTR Cell Signal Booster, visit support.weboost.com or call 1-866-294-1660 for assistance.
Safety Guidelines
Follow these safety guidelines when installing or using the
Drive Sleek OTR Cell Signal Booster:
- Do not operate the product near flammable gases or fumes
- Do not modify or disassemble the product
- Do not expose the product to water or other liquids
- Use only the power supply provided with the product
Download the App weBoost App
Use our app to guide you through setting up a weBoost cell phone signal
booster in your home, business, or vehicle. Boost every network, including 5G,
right away.
Package Contents
Mounting
Step 1: Select the Mounting Location & Assemble the Outside Antenna
Select a mounting location on the vehicle. The outside antenna can be mounted
in any CB mount or antenna mounting point on the vehicle. For best performance
mount the antenna above the metal cab (it does not need to be above cab wind
deflector).
Depending on the type of truck, there may be built-in antenna mounting points.
If the vehicle does not have built-in mounting points, the antenna includes a
3-way mount that will work on vehicles with mirror rails. The antenna will
also work with third-party CB antenna mounts.
NOTE: Mount at least 12 inches from any other antennas. Free of
obstructions.
NOTE: If the vehicle is using two CB antennas with co-phase wiring,
removing one antenna will cause the reduced performance of the remaining CB
antenna.
Once you have determined the best location for the outside antenna and have
determined if mast extensions are needed, insert cable through the mast.
NOTE: Mast extensions may not be needed depending on your mounting
point.
If using mast extension(s) add thread locker (packets provided) to thread
point(s). Screw into place.
NOTE: Be sure the antenna is the correct height before applying thread
locker.
Add thread locker (packets provided) to thread point and screw on the side
exit adapter.
NOTE: When adding the side exit adapter hold the antenna vertically and
screw the adapter from the bottom up. This reduces cable twisting.
Step 2: Mount The Outside Antenna
These are some typical antenna mounting points. If the vehicle does not have built-in mounting points, a 3-way mount is included that will work on vehicles with mirror rails.
If installing with the antenna spring, assemble the 3-way mount as shown below.
Step 3: Route Outside Antenna Cable & Connect Booster
Connect the cable from the outside antenna to the cable adapter then to the
booster port labeled by simply pressing the connector in until you hear
“click”.
NOTE : Connecting cable from outside antenna to booster does not booster
does not
The included Velcro® can be used to mount the booster out-of-the-way on the
floor under a seat or mounted in the back of the cab. It is best to mount in a
place where the cables cannot be tripped over or snagged (damaging the
booster).
NOTE: The “hook” side of the Velcro® (already on the booster) can be used
to attach to the carpet of many vehicles. Step 4: Route Fixed Booster Cable & Connect To
Cradle
Place booster behind seats or in back area of vehicle and route the 15 foot
fixed cable to the front of the vehicle where the cradle will be
located.
Connect booster cable to sleek cradle cable.
Step 5: Connect System To Power
Connect the power to the 12V* CLA port on your vehicle and route power cable
back to the booster.
NOTE: We recommend routing with the same path as the cradle/booster cable
(under mats and between seats).
Connect power cable to booster port labeled
NOTE: The booster will be on whenever there is power from the 12V CLA port. If your vehicle always has power going to this port, you may want to unplug this when you’re not driving so the booster does not drain your battery. *Only 12V ports are supported.
Step 6: Insert Your Phone Into the Cradle
Make sure you have plenty of slack in the cable going up to the cradle
(Velcro® straps included to manage excess cable). Insert your phone into sleek
cradle and watch your signal increase!
NOTE: A magnetic mount is provided which provides a versatile, safe and
functional smartphone solution.
IMPORTANT : The FCC requires to never use the cell phone in the cradle
next to your ear.
Troubleshooting
-
Solid White (LED on sleek cradle)
This indicates that your booster is functioning properly and at maximum gain. -
Light Off (LED on sleek cradle)
Check/secure power connections to the CLA, booster, and cradle. If light shuts off, remove from vehicle port and plug back in to reset the system. For any questions or assistance contact our weBoost Customer Support Team (1-866-294-1660). -
Dropped Calls
If you are regularly experiencing dropped calls in the same areas, turn off VoLTE/HD Voice in your phone’s settings.
Safety Guidelines
Use only the power supply provided in this package. Use of a non-weBoost
product may damage your equipment.
Any antenna used with this device must be located at least 8 inches from all
persons.
FCC requires to never use the cell phone in the cradle next to your ear.
This is a CONSUMER device.
BEFORE USE , you MUST REGISTER THIS DEVICE with your wireless
provider and have your provider’s consent. Most wireless providers consent to
the use of signal boosters. Some providers may not consent to the use of this
device on their network. If you are unsure, contact your provider.
In Canada, BEFORE USE y ou must meet all requirements set out in ISED
CPC-2-1-05.
You MUST operate this device with approved antennas and cables as
specified by the manufacturer. Antennas MUST be installed at least 20 cm
(8 inches) from (i.e., MUST NOT be installed within 20 cm of) any person.
You MUST cease operating this device immediately if requested by the FCC
(or ISED in Canada) or licensed wireless service provider.
WARNING. E911 location information may not be provided or may be
inaccurate for calls served by using this device.
FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05,
SEE BELOW:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html
FOR MORE INFORMATION ON REGISTERING YOUR SIGNAL BOOSTER WITH YOUR WIRELESS
PROVIDER, PLEASE SEE BELOW:
T-Mobile/Sprint/MetroPCS:
https://www.t-mobile.com/support/coverage/register-a-signal-booster Verizon
Wireless: http://www.verizonwireless.com/wcms/consumer/register-signal-
booster.html
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-
registration.jsp
Antenna Kit Options
The following accessories are certified by the FCC to be used with the Drive
Sleek OTR.
This radio transmitter 4726A-460035 has been approved by innovation, Science
and Economic Development Canada to operate with the antenna types listed
below, with the maximum gain indicated. Antenna types not included in this
list that have a gain greater than the maximum gain indicated for any type
listed are strictly prohibited for use with this device.
FIXED INSIDE ANTENNA KIT OPTIONS
Kit #| Coax Type| Ln(ft)| Antenna Type| Ω
311251| RG-174| 4| Cradle Antenna| 50
FIXED OUTSIDE ANTENNA KIT OPTIONS
Kit #| Coax Type| Ln(ft)| Antenna Type| Ω
311215| LMR-100| 10| Mini-Mag SMB| 50
311229| RG-58| 15| 4G Trucker| 50
311230| RG-6| 25| 4G RV OTR| 75
314405| RG-58| 14| 4G NMO| 50
Specifications
c | U470035 |
---|---|
Model Number | 460035 |
FCC ID: | PWO460035 |
IC ID: | 4726A-460035 |
Frequency | 698-716 MHz, 729-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz, |
1710-1755/2110-2155 MHz
Power output for single cell phone (Uplink) dBm
| Maximum Power
700 MHz
Band 12/17
18.74
| 700 MHz
Band 13
21.57
| 800 MHz
Band 5
22.65
| 1700 MHz
Band 4
25.56
| 1900 MHz
Band 2
19.19
Power output for single cell phone (Downlink) dBm| 700 MHz
Band 12/17
2.1
| 700 MHz
Band 13
2.1
| 800 MHz
Band 5
-2.5
| 2100 MHz
Band 4
-0.6
| 1900 MHz
Band 2
2.5
Noise Figure| 5 dB nominal
Power Requirements| 12 V 1.5 A / USB 5V 2.1 A
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor.
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. This device complies with Part 15 of FCC rules. This device contains license-exempt transmitter(s)/receiver(s that comply with Innovation, Science and Economic Development Canada’s license- exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)) This device must accept any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly approved by weBoost could void the authority to operate this equipment.
2 YEAR WARRANTY
-
weBoost Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.
-
Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by weBoost. weBoost shall, at its option, either repair or replace the product.
-
This warranty does not apply to any Signal Boosters determined by weBoost
to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. -
Replacement products may include refurbished weBoost products that have been recertified to conform with product specifications.
-
RMA numbers may be obtained by contacting Customer Support
DISCLAIMER: The information provided by weBoost is believed to be complete and accurate. However, no responsibility is assumed by weBoost for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.
NEED HELP?
Phone: 1-866-294-1660
Copyright © 2017 weBoost. All rights reserved.
weBoost products covered by U.S. patent(s) and pending application(s) For
patents go to: weboost.com/us/patents
NOT AFFILIATED WITH WILSON ANTENNA
References
- Cell Phone Signal Boosters for Home, Cars, & More - weBoost
- Register a signal booster | T-Mobile Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>