DNT000014 DoorAccess PRO Fingerprint Door Handle Instruction Manual

DNT000014 DoorAccess PRO Fingerprint Door Handle

Product Information: Fingerprint Door Handle DoorAccess PRO

The Fingerprint Door Handle DoorAccess PRO is an access control device intended for indoor use. It can be installed on doors with a drill hole spacing of 4 cm. The device comes with operating instructions and can be programmed to store user fingerprints, PINs, and mastercodes. It also has options to set tonal and visual indicators for access and programmable relay- activation time.

Technical Specifications

• Item number: DNT000014
• Intended use: General access control device for indoor use
• Drill hole spacing: 4 cm
• Programming options: User fingerprints, PINs, and mastercode
• Indicator options: Tonal and visual signals
• Relay-activation time: Programmable

Product Usage Instructions

Before installation and commissioning of the Fingerprint Door Handle DoorAccess PRO, please read the operating instructions completely and keep them for future reference. If you give the unit to other persons for use, also hand over these operating instructions.

Installation/Assembly

Note: In most cases, you can continue to use your existing lock.
Please check the drill hole spacing of your door. For DoorAccess PRO this is 4 cm.

Programming

To program the Fingerprint Door Handle DoorAccess PRO, follow these steps:

1. Enter the own/new mastercode
2. Program the user ID (for tracking access attempts)
3. Program the user fingerprints or PINs
4. Set the indicator options
5. Set the relay-activation time
6. Exit the programming mode

Operating

To operate the Fingerprint Door Handle Door Access PRO, follow these steps:

1. Scan your fingerprint or enter your PIN
2. The device will activate the relay if the fingerprint or PIN is a match
3. The device will also provide tonal and visual signals to indicate a successful access attempt

Maintenance/Safety

Note: Improper handling or failure to observe the safety instructions and the operating instructions may cause damage to property or personal injury. In such cases, all warranty claims are void! Please follow these maintenance and safety instructions:

• Periodically check the device for damage or wear
• Do not modify the device
• Do not expose the device to moisture or extreme temperatures
• Keep the device out of reach of children

Disposal

Please dispose of the Fingerprint Door Handle Door Access PRO in accordance with local regulations and guidelines.

Contact

If you have any questions or concerns regarding the Fingerprint Door Handle Door Access PRO, please contact our customer support at [insert contact information].

Please read these operating instructions completely before installation and commissioning and keep the operating instructions for future reference. If you give the unit to other persons for use, also hand over these operating instructions.

Function

The fingerprint door handle Door Access PRO allows easy access via the biometric access feature „fingerprint“ as well as via numerical code. For increased access security, both types of access can be combined. The device can manage up to 255 accesses. The fingerprint door handle also contains the switching relay for releasing the door lock supplied. The inside door handle also allows the door to be opened at any time (emergency function), the outside door handle can alternatively be operated with a mechanical key.

• Robust fingerprint door handle with integrated switching relay and supplied lock insert
• Capacitive fingerprint sensor, touch keypad
• Digit code access with 4 to 6 digits, input field backlit, with automatic switch-off after 5 s
• For up to 255 accesses (100 fingerprint + 155 PIN)
• Access via fingerprint, numeric code or combined possible
• Multi-color status display, internal signal transmitter
• Mains-independent battery operation, battery life up to 6 months (at 30 actuations/day), low battery warning
• USB port for emergency power supply, e. g. for a power bank
• Emergency opening option outside via mechanical key

Intended use, scope of delivery

The Door Access PRO is intended for use as a general access control device. It is intended purely for indoor use. We accept no liability for consequential damage resulting from non-observance of these rules of use and the operating instructions; warranty claims are also void. This also applies to conversions and modifications.

Scope of delivery:

• Fingerprint door handle Door Access PRO
• Lock insert
• 2x mechanical key
• Mounting material
• Operating instructions
• Screwdriver

Operating, maintenance and safety instructions

Warning
Used to mark safety instructions or to draw attention to particular hazards and risks.

Note
Used to indicate additional information or important notes.

• For safety and approval reasons (CE), unauthorized conversion and/or modification of the product is not permitted.
• Do not expose the unit to moisture, vibrations, constant heat, extreme cold, strong electromagnetic fields or mechanical stress.
• Observe all instructions in the operating instructions for connecting voltages. Incorrect  or reversed voltages will destroy the unit.
• Do not leave the packaging material lying around carelessly, plastic foils/ bags, poly-styrene parts, etc., could become a dangerous toy for children.
• If the unit has been damaged, take the unit out of operation and contact our service department.

We accept no liability for damage to property or personal injury caused by improper handling or failure to observe the safety instructions and the operating instructions. In such cases, all warranty claims are void! We accept no liability for consequential damage.

Do not open the unit, attempt to repair it or make any modifications or changes – this will invalidate the warranty. We accept no liability for consequential damage.

Product Installation/assembly

Note: In most cases you can continue to use your existing lock.
Please check the drill hole spacing of your door. For Door Access PRO this is 4 cm.

Door leaf thickness: 40–50 mm

• The cut-out for the lock insert must correspond to the dimensions shown in Step 1.

• Insert the lock insert sideways and fasten it with the supplied countersunk wood screws (Step 2).

• Screw the threaded bolts supplied into the threads of the outer door handle and the threaded extensions onto them. You can then use these to adjust the screw connection to the thickness of the door leaf.

• Guide the cable from the outer door handle through the supplied drive square and insert it into the outer door handle (push it in as far as it will go).

• Insert the pre-assembled outside door handle into the door leaf (Step 3, (1)).

• Open the cover of the interior door handle by loosening the retaining screw on the handle end and push the cover open by inserting the screwdriver into the screw opening and gently levering the screwdriver upwards.
  Note: Only open the cover via the screw opening as described here. Do not lever out the cover, e.g. with a screwdriver or knife – this will damage the cover.

• Now plug the cable connector into the corresponding socket.
  If necessary, use slim assembly pliers or tweezers for this purpose.

• Make sure that the plug is inserted with the correct polarity. It can only be inserted in one direction without mechanical resistance. The three raised knobs must be on the open side of the socket.
  Warning: Only insert the plug when there are no batteries in the battery compartment! In case of an accidentally incorrectly inserted plug, the unit may be damaged!

• Then place the inner door handle on the drive square and screw the inner door handle onto the threaded bolt (Step 3, (2)) with the threaded screws provided.
  Note: To do this, please remove the battery holder in order to tighten the screw below the handle through the hole that is now exposed. Then reinsert the battery holder.

• Insert four micro-batteries (AAA/LR03, alkaline) into the battery compartment with the correct polarity according to the polarity markings. The unit confirms correct insertion with a short signal tone.

• Replace the cover (insert it under the retaining edge at the end opposite the screw connection and then lower it onto the handle) and screw the cover in place with the retaining screw.

• Now the unit is ready for programming.

Sound and light signals
Signal/Status    LED     Sound signal
Stand-By           Off      Off
Key press   Off (keypad: On) 1x
Start programming mode Red 1x
Device in programming mode Orange 1x
Error/wrong entry 3x red (LED ring pink) 3x
Fingerprint valid LED ring green 1x
Door opener active Green 1x
Battery warning Orange 3x (Delete: Press one button)

Programming

Resetting the unit to factory settings
If the programming steps described below cannot be completed successfully as described, you should reset the unit to the factory settings.

Please note!
Resetting the device does not delete the stored access data! If the unit is passed on, the access data must be deleted manually!

• Open the battery compartment, take out one of the batteries.
• Press the reset button, hold it down while you reinsert the battery with the correct polarity.
• The acknowledgement LED above the keypad lights up orange and after approx. 5 s the unit acknowledges the rest with a beep and a short green flash of the acknowledgement LED.
• Now close the battery compartment again.

Operation/programming – brief overview
Separators are only for clarity, do not enter!

Own/New
Enter master code| 0 – new code (6 digits) – # – repeat code – #
Delete user| 2 – Enter fingerprint/user pin – #
can thus be continued for further users
2 – User ID – #
can thus be continued for further users
Delete all users| 2 – Master code – #
Finish programming| *
Open door| Authorised fingerprint/PIN – #
Close lock immediately| 0 – #

Programming differs depending on the type of access.
Follow the respective programming instructions.

Assigning user IDs facilitates the tracking of access attempts.

Possible user IDs:

• Fingerprint: 0…98: Master Fingerprint User ID: 99
• PIN: 100…254; 4 to 6 digits are permitted for access via PIN

Programming the master code

Add user with fingerprint
Read in user fingerprint, automatic ID assignment

or

Read in user fingerprint, Manual ID assignment

| 1 – Enroll fingerprint – Repeat fingerprint enrollment (enrollment can be continued like this) – #

1 – User ID – # Scan fingerprint – Repeat scan fingerprint – Repeat scan fingerprint – #

Add user with PIN
Read in user PIN,| 1 – Read in PIN – Read in fingerprint
automatic ID assignment| repeat (the reading can be continued in this way) – #
or|
Read in user PIN,|
Manual ID assignment| 1 – User ID – # Read PIN – #
Finish programming| *

Delete user

Add/Delete Master Fingerprint
One can also add or delete users with the master fingerprint.

Add Master Fingerprint

or

Delete Master Fingerprint

| 5 – Scan fingerprint – Repeat fingerprint scan – Repeat fingerprint scan – #

5 – Master code – #

Finish programming| *

If the master fingerprint is deleted, a new master fingerprint can only be entered after a battery has been removed and reinserted.

Inserting the master fingerprint to add and delete users

Step 2: Read user fingerprint three times* (or PIN – #) (Step 2 can now be continued to add further users Step 3: Read in master fingerprint

Delete User (Fingerprint/PIN)| Step 1: Read in master fingerprint twice within 5 s Step 2: Read in user fingerprint* (or PIN – #)

( Step 2 can now be continued to add further users Step 3: Read in master fingerprint

Please note that the master fingerprint can also be used to open the lock, but the programming mode is also started. Therefore, the master fingerprint should not be used for normal opening.

Set the behavior of the switching relay
This sets the active time or the behavior of the switching relay.

(relay remains energized for 1 to 99 s = door open, factory setting: 5 s)

or|
Set toggle mode| 30 – #

(Switches the relay permanently to one position until the input is made again, then the relay goes permanently to the other position). This setting is used, for example, if a door is to be freely traversable for a longer period of time.

Finish programming| *

Set access type
For multiple access attempts with the same fingerprints/PINs, a time of 5 seconds must not be exceeded, otherwise the unit will return to standby mode without reacting.

Set displays/acknowledgement signal

Operation

Door opening only with fingerprint

• Place registered finger

Open door only with PIN

• Enter registered PIN, confirm with #

Open door with multi-PIN/fingerprint

• Registered multi-access (2-9 users, see chapter) 5.9 hang up/enter

Open door with PIN or fingerprint

• Registered access (see chapter) 5.9 hang up/enter

Technical data

• Number of users:………………………………………………………255 (100 fingerprints/155 PINs)
• fingerprint reader:………………………………………………………………………………….. capacitive
• PIN:………………………………………………………………………………………………….. 4 to 6 digits
• Relay active time:……………………………………………………….. 0 to 99 s (factory setting: 5 s)
• Power supply:………………………………………………………………….6 VDC (4x Micro/AAA/LR03)
• Current consumption:……………………………………… Standby: <25 μA, Active: max. 120 mA
• Battery life:……………………………………………………….. 6 months (at 30 operations per day)
• Ambient conditions:……………………………………………………………………. . -25 °C to +60 °C
• Dimensions (W x H x D):……………………………………………………………. 29 x 165 x 65.5 mm
• Weight:……………………………………………………………………………………………………..1200 g

Declaration of conformity

Hereby, dnt Innovation GmbH, Maiburger Straße 29, 26789 Leer, Germany, declares that the device is „Fingerprint door handle Door Access PRO“ is in compliance with the essential requirements and the other relevant provisions of Directive 2014/30/EU.

The declaration of conformity can be found at the following address: www.dnt.de

Disposal

Do not dispose of the appliance in household waste!
Electronic devices must be disposed of in accordance with the directive on waste electrical and electronic equipment via the local collection points for waste electronic equipment!

Observe battery regulation!

Batteries and rechargeable batteries do not belong in household waste. According to the Battery Ordinance, you are obliged to return used or defective batteries to the local battery collection points or to your dealer!

**Contact

**

Do you have questions about the product or its operation?
Our technical customer service will be happy to provide you with comprehensive and qualified information: E-mail: info@dnt.de

1st edition English 08/2022
Documentation © 2022 dnt Innovation GmbH
All rights reserved. No part of these operating instructions may be reproduced or duplicated in any form without the written consent of the publisher.
It is possible that these operating instructions still contain typographical errors.
has defects or printing errors. However, the information in these operating instructions will be checked regularly and corrections will be made in the next edition.
We accept no liability for errors of a technical or printing nature and their consequences. All trademarks and industrial property rights are recognized. Changes in the sense of technical progress can be made without prior notice. DNT000014-08/2022, Version 1.0

Importer: dnt Innovation GmbH
Maiburger Straße 29 · 26789 Leer · Germany · www.dnt.de

References

• dnt Innovation GmbH: hochwertige Elektronik-Lösungen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>