NAIFAY X6M Car Stereo 7 Inch HD Touchscreen Rearview Camera User Manual

NAIFAY X6M Car Stereo 7 Inch HD Touchscreen Rearview Camera

Preface

In order to prevent injuries and fires, pls pay attention to the following instructions:

• In order to prevent short circuit and so on, do not drop the metal objects in the device.
• If there is smoke or peculiar smell the device, pls turn off the power at once.
• Pls do not make the device falling or strong collision. In order to prevent device failure, pls observe the following note:
• Pls do not install the device in the place of strong sunlight, high temperature, high humidity or dusty.
• Pls replace the fuse which is the same specification. If you are using different specification of the fuse, may cause failure of the device.
• In order to prevent short circuit, pls pull out the power wire when you replace the fuse.
• In order to be able at any time to deal with road and traffic conditions change, pls lower the volume when driving.
• Pls do not get the device wet when washing car, this may cause short circuit, then fire or other failure will be caused.

Warning

1. Only connect the unit to a DC 12V power supply with negative grounding.
2. Never instal the unit where the operation for safety driving is restrained.
3. Never use the video display function in the front when driving to prevent the violation of laws regulation and also to reduce the risk of traffic accident except using for rear view video camera.
4. Never expose the unit, amplifier, speakers to moisture or water to prevent electronic sparks or fires.
5. Pls don’t change the fuse in the power cord without professional guidance; improper fuse may cause damage to this using unit or even cause fire.

Installation

Thank receive the product, please do not take the product directly to the car for instal lation, because the product is in the after a long journey, it may affect the product. Please try the machine before instal l ing. Test method: Take the mach i ne to the battery of the car and test it. This car stereo appl ies to a power supply voltage at 12V DC, connect  the red and yell ow wires of the power cord of the machine together and  connect it to the positive pole of the battery.power cord is connected to the negative pole of the battery. Wait for 10 seconds after connect ing. press each button of the machine to see if the machine can boot normal ly. If it can be turned on, it means there is no prob l em, you can install it. If the test mach i ne can not start normal ly, please again. Confi rm that you fol low the steps of our test method in strict accordance with the operat i on. If the probl em is still not solved, please contact our work in time. Thank you for your cooperat i on. you very much for purchas i ng and using our products, when you The black wire of the If you have any questions, please do not hes i tate contact us.

Wiring Method

When the yellow line B+ and the red ine ACC have a 12V positive power at the same time. the unit can be tumed on normally.
The yellow line B+ keeps the power on and the machine has a memory function. 8 speaker cables. each cable can not be groun ded. can not be shared. can not touch the line. otherwise there will be no sound output, output sound distortion. machine fever and so on.

warning:  Pls check the speaker line caref lly before installation. If any grounding or touching. pls connection again or the unit will be burned.

Machine Fixed Reference Metho

Steering Wheel Control

1. Connect the positive pole of the or iginal steer ing wheel to the KEY (brown)Tine of the machine plug.
2. Connect the negat i ve pole of the or iginal find the “SWC” functi on and enter the GND (Black) wire of the machine plug.
3. In the “settings” interface, find “Steer ing enter controls”and enter.
4. Enter the steer ing wheel control learning interface and press the button to learn. After the learning is successful, click the “confi rm” button on the page.
   After saving. you can use the buttons on the original steering wheel to control the mach one. Learning method: press and hold a button on the steer ing wheel of the or igina l car without letting go, find the button icon corresponding to the functi on of the button on the steer ing wheel of  the machine. Click this icon to change the color, indi cat ing that the button has been successful ly learned, accord ing to the same The way you can learn other buttons. After all the keys have been learned,olick the “Confi rm” button on the page to save the sett ings. If you need to relearn, please cl ick the “RESET” button on the page and then re-learn.

Button Light Settings

1. In the “Setup” interface, find the “other “option and click “Color I I get”.
2. In the pop-up dialog box, the user can select a single color or select automat i c change and click “YES” to confi rm the selection.

Phone Link For Android

The system supports most Android phones below Android 11.0. If you can not connect, please contact us.

1. Open deve l oper mode. (Since different mobile phones have different ways to open the developer mode, please find the way to open the developer mode for the corres ponding mobi le phone mode l through the browser. You on ly need to set it once, and then the connect i on does not need to be set again. )
2. Open “USB debugging” (Since different mobi le phones have different ways to open “USB debugg i ng”. please find the way to open “USB  debugging” for the correspond i ng mobi le phone model through the browser. You only need to set it once, and then the connec- tion does not need to be set again.)
3. Connect the mobi le phone to the car car stereo through the USB cable, down load the software accord ing to the mobi le phone prompt, and then the mobi le phone screen content can be projected onto the car stereo.

Phone Link For iphone

• For ios, Support Apple 13 series and below mobi le phone connect i ons. Please contact our customer service per sonne l in case of fai lureto connect.
• Connect the machine and mobile phone with the or iginal data cable.
• When the phone pops up a dialog box: Trust
• This Computer? Select Trust to enter the interconnect mode. (If the phone has a set password, you need to enter the password first.)

Basic operation

1. when use reversing rear view function. reversing video signal from the corresponding port input connection back line, when reversing will automatically switch to reversing visual state.
2. Audio/Vedio input(optional) Connect audio/Vedio lines, press Mode can select AUX-2 state.
3. bluetooth function only for the unit with bluetooth

After connecting the mobile, the bluetooth symbol turn green means the connection is ok, when calls come in will enter into the bluetooth interface automatically, press’answering the phone, press”hanging up the phone.

Remote Control Description

1. Power switch
2. Left
3. ode switch
4. Last song
5. USB/SD
6. Volume-
7. Band/Automatic Station search
8. Digital key
9. Aup
10. Menu
11. Confirm/Play/Pause
12. Right
13. Under
14. Next song
15. Choice
16. Volume+
17. Answer the phone
18. Hang up

Custom Logo

1. Click the “Settings” opt ion of the home page.
2. Click the “Other” option in the “Sett i ngs” interface.
3. Slide up in the “Other” interface. As shown in the picture.
   Then you can see the “Set logo” option. After clicking it, you can select the logo you want from 20 automob i le brands.

BLUETOOTH

PHOTO

RADIO

MUSIC

MOVIE

Common Problems and Simple Troubleshooting

• Unable to boot normally

  • Reason for not boot ing “Yel low” “Red” “BIlack” these 3 lines only connected 2 Iline of them, so it will not start, it should be that the yel low line is connected to the positive pole, red line to the key control line, black to the negat ive pole, less connect i on or wrong connect i on does not boot. The or iginal car line and unit wiring can not be connected to the color, the color of the or iginal car line is not standard, if you connect Iike that it can not on ly be turned on but also may burn. The or iginal car plug can’t be plugged directly into the new unit, even if it just plugs in, it can’t be used, otherwi se it won’t be turned on or burned. The 3 wires are connected right, but it does not boot. Check if the fuse on the yel low line is broken. If there is no problem with the fuse, twist the yel low and red wires together. Turn on the key and press the unit’s power button to see if itcan be turned on.
    Every time you change the fuse, it burns. Please don’t change it aga in The reason is that when you first connect the positive and negat ive poles, the protect ion circuit of the un it is short-circuited. The unit can be repaired under the  guidance of our master. No basis can only be returned to the after- sales or new unit. If these are no problem, or al so don’t boot, please make the final step to confi rm, find a 12V battery or 12V power supply “yel low” and “red” twist together with the positive, black to the negat i ve pole, press the button check if it can  boot or no, if you can boot, it showed that the or iginal car line is not right  connect, or there is a probl em with the car 1 ine. If it can’t be boot, the unit is  broken. Does not boot un it, check the line careful ly, do not blindIy suspect the unit prob lem.

• Automatic shut-down

  • Automatic shutdown usually has the following conditions The cable error connect: If the blue cable (automat ic antenna power supp ly) is con nected to the power cable of the un it, an automat ic shutdown will occur. Please fol low the correct wiring method to solve the problem.  The voltage is unstable: please find a 12V-5A which one is the power supply and re-tested to see if it will automat i cal ly shut down or no. If it does not automat- ical ly shut down after the test, please replace the power supply. If it will auto-  mat i cal ly shut down, it is prob lem with the unit.

• 3 Having noise

  • The general situat i on of noi se is caused by two reasons
    The or igi nal speaker power is too smal. When the vol ume of the unit is turned up, there wi ll be noise.

  • Solution : When replacing the speaker or listen i ng to the song. the volume should not be too large. The speaker cable is grounded.

  • Soluti on: Take the iron speaker cable. Direct ly connected to the speaker cable of the unit.

• emote contro cannot De used Check if the battery of the remote control has power.
  Test method: Turn on the camera of the mobi le phone and al ign the light of the remote cont ro l, then press the button of the remote control to see if the phone will light up. If it is not lit, there will be no power. Rep l ace the battery; That IS, there is electricity, which proves that there is no problem With the remote control.
  Settings cannot be savedno memory)
  There is no memory funct i on, there is only 2 po ints in memory The yellow Iine and the red Iline are connected together (separate yel low to positive, red to key control). Yel low and red are rever sed (just change position).
  Car aud io with Bluetooth but if can’t work
  Check the phone to see if you can search for the unit code or no. Operation steps: turn on the unit, use the phone Bluetooth search, search for CAR-MP5, then click the connect i on, after connect ing, you can answer the phone or Bluetooth to play the song.
  PIN Code: 0000.

• Support no image of revers ing camera

  • General ly two situat i ons

• Connect the wrong line or less wiring. Camera connecti on method:

  • a The first step is to find accessor i es (accessory: one camera + one power cord  one video cable).
  • b The second step is to find the port of the wiring. First find the revers ing control ine on the power Iine of the unit. The control line is a pink line or  brown ine, connect this line to the pos itive pole of 12V and the screen wil turn blue. Find the back of the unit the CAME video input interface, find the positive  and negative of the backup ight. The thi rd step is to connect: there are two sockets on the camer a, the red socket is connected to the power cable, the yel low is inserted into the video cable, the red wire of the power cable and the wire of the video cable are screwed together on the positive pole of the rever se lamp, and the black wire of the power cable is not used, connected, the other end of the video cable is connected to the CAME video input interface on the back of the unit. Ihe red ine coming out of the video ine is connected to the reverse ing control line of the power line. The camera is broken. If the lamp that is proper ly wired to the camera is not lit, it will be broken and rep laced with a new one.

• 8 USB fl ash disk can not be played, the card slot does not enter the card?

  • USB flash disk can not play:
    Format the USB flash disk, and the file system is selected as: FAT32, re- download on or two songs and try again. If it still doesn’t work, please replace the USB flash dr ive.

  • The card slot does not enter the card:

  • Check whether the memory card is inserted, the plug is broken.

• 9 FM does not receive the program

  • Can not receive the station check the 2 points The antenna plug is not ful ly inserted, the antenna is disconnect or the line is disconnect. Search channe, hold AMS does not let go for 2 seconds. The unit will automat i- cally search or press the up and down button to perform a channel search. Can’t solve the above 2 points, Please unp lug the antenna plug and find a screwdri ver or a metal strip to insert it instead of the antenna.

• Just installed no sound
  Dear customers, the unit has been tested before shipment. If there is no sound, it is usual ly a wiring error or the or iginal car speaker wire is short-circuited with iron. Please do not doubt the un it. Acceding to the steps to check it. Check if the speaker cable is short-ci rcuited and connected. Please reconnect if you have any short circuit. Check how many speaker cables according to the or iginal speaker cable if there are only 2 speaker cables to prove that the or iginal car line does not match our unit, you need to reroute the or iginal car line. One speaker must lead to 2 speaker wires. 2 speakers must be have 4 speaker cables to avai lable.

• After a whi le there is no sound

  • Di sconnect all the speaker cable from the unit (do not remove all of them), and then find an external speaker to receive the gray and purple of the tail line of the un it. Green any group, and then try to see if there is any sound. If there is a sound, it is proved that the car’s speaker line is short-circuited with iron or the speaker is damaged. If there is no sound, the unit is broken.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>