MATRIX AUDIO element P2 Audio Power Amplifier User Manual
- June 10, 2024
- MATRIX AUDIO
Table of Contents
MATRIX AUDIO element P2 Audio Power Amplifier
Packing List
Parts and names
Front
-
Power on/Standby
After connecting to power supply, press this button to power on the unit, press it again to let the unit standby. -
LED indicator
The LED indicator will go off when the unit is standby. It flashes when the device is delayed starting, and will keep lit up after the device is started.
Rear
-
Mono mode input
In mono mode, a single amplifier drives 1 speaker. Connect amplifier to 1 channel of the front-end audio source device through an XLR cable. -
Stereo mode input
In stereo mode, a single amplifier drives 2 speakers. Both RCA and XLR cables can be used to connect to the left and right channel of the frontend audio source device. -
Mode/input switch
Working mode and input method can be set by this switch. There are 2 input methods, XLR and RCA, that are available for Stereo mode. In Mono mode, only XLR input takes effect.
To avoid misoperation, toggling this switch when the unit is on will not change the current working mode immediately. The switch will take effect after the unit enters standby and starts again.
-
Speaker output
Please refer to the diagram below for speaker connection in Stereo mode.
Please refer to the diagram below for speaker connection in Mono mode.
-
USBType-C
For firmware update. -
Trigger input/output
Connect to audio devices with trigger ports through a 03.5 mm mono plug cables, to achieve a linkage control between the amplifier and other devices. The trigger output provides a 12V DC signal. -
AC input
This unit adapts to AC100-120V and AC220-240V power voltage range automatically. Please make sure to use the product in the power voltage range mentioned above.- Please use the power cable which includes an earth wire. Please ensure you have a reliable earth wire connection. Otherwise, the casing of the unit may have a slightly charged touch. If you need the unit to be turned off completely, please unplug the power cable.
Appendix
Technical specifications
Stereo mode RCA input
Input impedance : 47kO
Gain : 28dB@lkHz
Stereo mode RCA input
Input impedance : 47kO
Gain : 34dB@lkHz
Mono mode XLR input
Input impedance : 47kO
Gain : 34dB@lkHz
Speaker output
-
Stereo mode
Output power: 2x230W@l% THD+N, 20Hz-20kHz, 40
2x110W@l%THD+N, 20Hz-20kHz,8O
DNR: 112dBA-weighting
Frequency Response : 20Hz-20kHz ±0.3dB
THD+N : 0.008%@ lW
Output impedance : <25m -
Mono mode
Output power: 850W@ 1% THD+N, 20Hz- 20kHz, 40
500W@ 1% THD+N, 20Hz-20kHz, 80
DNR :12ldB A-weighting
Frequency Response :20Hz-20kHz ±0.3dB
THD+N : 0.004%@1W
Output impedance : <30m
Trigger
Trigger in : DC 6-12V <10mA
Power
Trigger out : DC 12V/50mA MAX
Power Voltage : AC 100V-120V 50/G0Hz / AC 220V-240V 50/G0Hz
Standby Power Consumption : < 5W
Maximum Power Consumption: 1200W
Other specifications
- Weight: 3.7kg (8.16 pounds)
- Size: Width 340mm(l3.39 inches)
- Depth 259mm(l0.20 inches)
- Height 58mm(2.28 inches)
Attention
- This product is for indoor use only.
- For full ventilation, it is recommended to reserve a space of larger than 5 cm around the device.
- Do not cover the air vents with stuffs such as papers, tablecloths, and curtains to obstruct ventilation.
- Do not place stuff with flame, such as lighted candles, on the device.
- If the device is used in tropical areas, please be careful to prevent insects from entering the unit
- through the air vents.
- The device must not be subject to water droplets or splashes. Please do not place stuffs filled with liquids such as vases and cups on or near the device.
- Do not put stuffs around the device power plug and the AC power socket, in order to disconnect the power supply easily when needed.
Matrix Electronic Technology Co., LTD
+86-29-86211122
B-801, No.111 Fengcheng 5th Rd.,
Xi’an, China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>