Shakti Technology S3 Electric Pressure Washer User Manual

Shakti Technology S3 Electric Pressure Washer

S3 S5 S7 Electric Pressure Washer

Description

The S3 S5 S7 Electric Pressure Washer is a high-pressure electric power washer designed for residential use. It is suitable for cleaning vehicles, machines, buildings, facades, etc. Pleasenote that this machine should never be used in potentially explosive areas, and water that is dirty, gritty, or contains any chemical products should not be used as they can impair its operation and shorten its life. Additionally, the unit can be placed horizontally but should not be stepped on when placed that way.

product Technical Specifications

What’s in the Box

• Electric pressure washer
• Pressure gun
• Outlet hose pipe
• Inlet pipe
• Needle clean-out tool
• Inlet filter set
• Soap dispenser
• User’s manual

Product Usage Instructions

Assembly Instructions

To assemble the electric pressure washer:

1. Attach the inlet pipe to the water inlet on the unit.
2. Attach the outlet hose to the water outlet on the unit.
3. Insert the inlet filter set into the water bucket filter.
4. Screw the inlet quick connector onto the inlet pipe.
5. Insert the needle clean-out tool into the inlet crystal filter to remove any debris.
6. Attach the extension rod to the pressure gun.
7. Insert the soap dispenser onto the pressure gun if needed.

product Operating Instructions

To operate the electric pressure washer:

1. Fill a bucket with clean water and place the inlet pipe into it.
2. Turn on the water supply.
3. Turn on the electric pressure washer using the on/off switch.
4. Adjust the pressure using the pressure gauge and pressure gun.
5. If using soap, fill the soap dispenser with detergent and adjust the nozzle to apply it.
6. When finished, turn off the electric pressure washer and turn off the water supply.

Product Maintenance

To maintain the electric pressure washer:

• Regularly clean the inlet filter set to prevent clogs.
• Keep the unit dry and store it in a safe place.
• Periodically check for any leaks or damage.
• Refer to the user manual for any other maintenance requirements.

Troubleshooting

If you encounter any problems with the electric pressure washer, refer to the following table:

poor connect between the plug and socket.
2) The switch or remote control switch may be broken, or the
battery depleted. 3) The voltage of the power is too low. 4)
Crankshaft and connect rod won’t lubricate well. 5) The capacitor
broken.| 1) Examine the power supply and make the plug & socket well
connected. 2) Repair or replace the switch, or replace the battery.
3) Consult with the electric supply. 4) Detach the fan cover from
the motor and turn the motor around. If after doing that it still
won’t work, take it to an agent for repair. 5) Take it to an agent
to replace the capacitor.
The nozzle cannot spray water or spray water in low
pressure.| 1) Nozzle is clogged. 2) The checking valve closes down. 3)
There is air in the hose. 4) Water sealing worn off. 5) The filter
net is clogged.| 1) Clear the nozzle. 2) Run the pump with water tap as water
supply for some minutes or clean the checking valve.

Contact Us

If you have any problems or questions about the S3 S5 S7
Electric Pressure Washer, please contact us.

THANK YOU FOR CHOOSING SHAKTI TECHNOLOGY ELECTRIC PRESSURE WASHER PLEASE READ THE OWNER’S MANUAL AND SAFETY INSTRUCTIONS CAREFULLY BEFORE OPERATING THE ELECTRIC PRESSURE WASHER. SAVE THIS MANUAL FOR FUTURE REFERENCE. IF YOU HAVE ANY PROBLEMS AND QUESTIONS, PLEASE CONTACT US.

PRODUCT DESCRIPTION

• This high-pressure electric power washer is intended for residential use to clean vehicles, machines, buildings, facades, etc.
• Never use the machine in potentially explosive areas under any circumstances!
• Do not use water that is dirty, gritty, or contains any chemical products, as these could impair operation and shorten the life of the machine.
• This unit can be placed horizontally. Do not step on when placed horizontal.

TECHNICAL SPECIFICATION

PRODUCT

1. Inlet Pipe
2. Water Bucket Filter
3. Inlet Quick Connector
4. Inlet Crystal Filter
5. Outlet Pipe
6. Pressure Gun
7. Soap Dispenser
8. Main Unit
9. Extention Rod

**All details will remain same for S3 & S7 Model Also

WHAT’S IN THE BOX

• Electric pressure washer
• Pressure gun
• Outlet Hose Pipe
• Inlet Pipe
• Needle clean-out tool
• Inlet Filter Set
• Soap Dispenser
• User’s manual

IMPORTANT!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a suffocation risk!

ASSEMBLY INSTRUCTIONS

1. Attach one end of the inlet pipe with the tap connector

2. Attach another end of the inlet pipe with the inlet connector.

3. Screw the inlet filter clockwise to attach with the main unit.

4. Push and attach the inlet connector with the inlet filter.

5. Turn ON the machine. Release the water for few minutes to release the air inside.
   (Without the outlet pipe connected)

6. Connect one end of outlet hose pipe with the oulet end of the machine.

7. Connect another end of the outlet hose pipe with the gun.

   • Inlet filter must be straight
   • Don’t bend inlet connector

OPERATING INSTRUCTIONS

• When making washing, especially with high pressure, make sure distance between the nozzles and object is enough otherwise damage to the object may occur.
• When the time slot of not use the machine for more than 5 min, please cut off the machine and press the gun trigger to release the pressure.
• The working pressure of the machine is set from the factory and the user should not adjust it higher, otherwise the machine may be damaged.
• It is normal that when it is working, there may be some water drops out form the water discharge holes in the pump juncture.
• When you want to stop the machine, please follow steps as below:
  1. Switch off the machine
  2. pull the plug off from the socket
  3. cut off the water supply (if the water is supplied from the tap).
  4. Press the trigger of the spray gun to release the pressure.
• The accessories like gun and hose matter the performance, so please take care of them any time.
• If the motor cannot work, please turn it off at once, or it may be burned.

MAINTENANCE

• Replace Engine Oil Regularly (Oil grade 15W-40)
  • A. After first 20 hours’ working, the engine oil must be replaced,(60-70ml oil can be filled).
  • B. Replace the second time after another 50 hours’ working and replace the oil regularly after each 100 hours’ working.
• Turn off the machine when you make maintenance for the machine
  • A. If the machine will be in storage for a long time, the left water in the pump much be drained off completely. Keep the machine in a dry and well ventilated condition.
  • B. If the water source is not very clean; the filter net should be cleaned regularly.

Problem   Cause  Possible Solution

The motor won’t run or stop running when it is working.| 1) No power supply or poor connect between the plug and socket.| 1) Examine the power supply and make the plug & socket well connected.
---|---|---
 | 2) The switch or remote control switch may be broken, or the battery depleted.| 2) Repair or replace the switch, or replace the battery.
 | 3) The voltage of the power

is too low.

| 3) Consult with the

electric supply.

 | 4) Crankshaft and connect rod won’t lubricate well.| 4) Detach the fan cover from the motor and turn the motor around. If after doing that it still won’t work, to agent for repair.
 | 5) The capacitor broken.| 5) To the agent to replace the capacitor.
The nozzle cannot spray water or spray water in low pressure.| 1) Nozzle is clogged.

2)  The checking valve closes down.

| 1)  Clear the nozzle.

2)  Run the pump with water tap as water supply for some minutes or clean the checking valve.

 | 3)There is air in the hose.| 3) Make firmly connecting of the water inlet hose to

eject the air.

 | 4) Water sealing worn off.| 4) Replace the water seal.
 | 5) The filter net is clogged.| 5) Clear the filter net.
Pressure unloads.| 1)  Pressure valve leaking water.

2. Pressure loader clogged 3)Mushroom nail worm off

3. Connecting between gun and hose leaking or gun leaking.

| 1)  Replace some O-rings or go to agent for repairs.

2)  Clear pressure loader.

3)  Replace the Mushroom nail.

4)  Tighten the connecting or replace the gun.

---|---|---
Water leaking on the pump.| 1) Supporting ring worn off| 1) Replace the supporting

ring.

 | 2) Water seal worn off.| 2) Replace the water seal.
 | 3) Plunger worn off.| 3) Replace the plunger.
Oil leaking on the pump.| 1) Some O-ring worn off.| 1) Replace some O-rings.
 | 2) Oil seal worn off.| 2) Replace the oil seal.
 | 3) Add to much oil to the crankshaft case.| 3) Drain some oil until the oil level is in middle or 2/3

level of the oil window.

 | 4) Air vent clogged.| 4) Clear the air vent.
When stop the spray gun, the pressure doesn’t return to zero but rise & fall continuously.| 1) Returning valve damage on outlet pump side.| 1) Replace the returning valve.

Warning

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
Do not dispose this product by normal household waste, but take it to a collection point and recycling of electrical and electronic equipment. This is indicated by the symbol on the product, user manual or packaging. Re-use, material utilization or other forms of old appliances, you make an important contribution in protecting our environment.

CONTACT US

Shakti Technolgy Rajkot, Gujarat (India).
[email protected]
+91 99090 84777+91 95582 85760
www.shaktitool.com

References

• Nexcess

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>