DAEWOO 32DM54HA Colour Television with Remote Control Instruction Manual

: June 10, 2024
: Daewoo

OPERATING INSTRUCTIONS
32DM54HA
Colour Television with Remote Control

Safety Information

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains.
The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable. If the TV set not disconnected electrically from the mains, the device will still draw power for all situations even if the TV is in standby
Note: Follow the on screen instructions for operating the related features.

IMPORTANT – Please read these instructions fully before installing or operating
WARNING: This device is intended to be used by persons (including children) who are capable / experienced of operating such a device unsupervised, unless they have been given supervision or instruction concerning the use of the device by a person responsible for their safety.

Use this TV set at an altitude of less than 5000 meters above the sea level, in dry locations and in regions with moderate or tropical climates.
The TV set is intended for household and similar indoor use but may also be used in public places.
For ventilation purposes, leave at least 5cm of free space around the TV.
The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.
The power cord plug should be easily accessible. Do not place the TV, furniture, etc. on the power cord. you an electric shock. Handle the power cord by the plug, do not unplug the TV by pulling the power cord.
Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock.
Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced, this Do not expose the TV to dripping or splashing of such as vases, cups, etc. on or over the TV (e.g., on shelves above the unit).
Do not expose the TV to direct sunlight or do not or near the TV.
Do not place any heat sources such as electric heaters, radiators, etc. near the TV set.
Do not place the TV on the floor and inclined surfaces. out of the reach of the babies, children and domestic animals.
Carefully attach the stand to the TV. If the stand is prevent the TV from tilting. Do not over-tighten the screws and mount the stand rubbers properly.
Do not dispose of the batteries in fire or with

WARNING

Batteries must not be exposed to excessive heat
Excessive sound pressure from earphones or headphones can cause hearing loss.

ABOVE ALL – NEVER let anyone, especially children, push or hit the screen, push anything into holes, slots or any other openings in the case.

Caution	Serious injury or death risk
Risk of electric shock	Dangerous voltage risk
Maintenance	Important maintenance component

Markings on the Product

The following symbols are used on the product as a marker for restrictions and precautions and safety instructions.
Note such information for security reasons.
Class II Equipment: This appliance is designed in such a way that it does not require a safety connection to electrical earth.
Hazardous Live Terminal: The marked terminal(s) is/are hazardous live under normal operating conditions.
Caution, See Operating Instructions: The marked area(s) contain(s) user replaceable coin or button cell batteries.
Class 1 Laser Product: This product contains Class 1 laser source that is safe under reasonably foreseeable conditions of operation.

WARNING
Do not ingest the battery, Chemical Burn Hazard This product or the accessories supplied with the product may contain a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
– – – – – – – – – – – –

A television may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

ALWAYS use cabinets or stands or mounting methods recommended by the manufacturer of the television set.
ALWAYS use furniture that can safely support the television set.
ALWAYS ensure the television set is not overhanging the edge of the supporting furniture.
ALWAYS educate children about the dangers of climbing on furniture to reach the television set or its controls.
ALWAYS route cords and cables connected to your television so they cannot be tripped over, pulled or grabbed.
NEVER place a television set in an unstable location.
NEVER place the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support.
NEVER place the television set on cloth or other materials that may be located between the television set and supporting furniture.
NEVER place items that might tempt children to climb, such as toys and remote controls, on the top of the television or furniture on which the television is placed.
The equipment is only suitable for mounting at If the existing television set is going to be retained and relocated, the same considerations as above should be applied.

Apparatus connected to the protective earthing of the building installation through the MAINS connection or through other apparatus with a connection to protective earthing – and to a television distribution system using coaxial cable, may in some curcumin distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator)

WALL MOUNTING WARNINGS

Read the instructions before mounting your TV on the wall.
The wall mount kit is optional. You can obtain from your local dealer, if not supplied with your TV.
Do not install the TV on a ceiling or on an inclined wall. accessories. the TV from fall. Do not over-tighten the screws.

Figures and illustrations in this user manual are provided for reference only and may differ from the actual product appearance.
Product design and specifications may be changed without notice.

Introduction

Thank you for choosing our product. You’ll soon be enjoying your new TV. Please read these instructions carefully Ihr’nnInWrtant7f7==h=he,yougeZ:st from your and correct installation and operation.

Accessories Included

Remote Control
Batteries: 2 x AAA
Instruction Book
Quick Start Guide
Power Cord

Features

Remote controlled colour TV
Android,’ operating system
Google Cast
Voice Search
Fully integrated digital terrestrial/cable/satellite TV (DVB-T-T2/C/SS2)
HDMI inputs to connect other devices with HDMI sockets
USB input
Composite inputs for extremal devices (such as DVD Players. PVIR, video games. etc.)
Stereo sound system
Teletext
Headphone connection
Automatic programming system
Manual tuning
Sleep timer
On/Off timer
Switch off timer
Picture off function
No signal auto power off function
VGA input
Themed (LAN) for Internet connectivity and service
802.11 a/b/g/n/ac built in WLAN Support
HbbTV

High Dynamic Range (HDR)/ Hybrid Log-Gamma (HLG)
Using this feature the TV can reproduce greater dynamic range of luminosity by capturing and then combining several different exposures. HDRIHLG promises better picture quality thanks to brighter, more realistic highlights, more realistic colour and other improvements. It delivers the look that filmmakers intended to achieve, showing the hidden areas of dark shadows and sunlight with full clarity, colour and detail. HDR/FILG contents are supported via native and market applications, HDMI, USB inputs and over DVB broadcasts.

Stand Installation & Wall Mounting

Assembling / Removing the pedestal Preparations Take out the pedestal(s) and the TV from the packing case and put the TV onto a work table with the screen panel down on the clean and soft cloth (blanket. etc.)

Use a flat and firm table bigger than the N.
Do not hold the screen panel part.
Make sure not to scratch or break the N.

Assembling the pedestal

Plce7n(Isi) eorrtredresa)r on lo’fethset stand mounting
lunnstedrt Zest: rnedwiss pprroov4I: acyl rtcelctiighten them gently

Removing the pedestal from the TV Be sure to remove the pedestal in the following way vherriu sing the wall-hanging bracket or repacking.

Put the TV onto a work table with the screen panel down on the clean and soft cloth. Leave the stand(s) protruding over the edge of the surface.
Unscrew the screws that fix the stand (s).
Remove the stand(s).

When using the wall mount bracket
Your TV is also prepared for a VESA-compliant wall mount bracket. If it is not supplied with your TV, contact local le . r to purchase the recommend wall- Holes and measurements for wall mount bracket installation;

DAEWOO 32DM54HA Colour Television with Remote Control - Wall Mounting
1

VESA WALL MOUNT MEASUREMENTS

Antenna Connection

Connect the aerial or cable TV plug to the AERIAL INPUT (ANT) socket or satellite plug to the SATELLITE INPUT (LNB) socket located on the rear side of the TV.
Rear side of the TV

Satellite
Aerial or cable

**** If you want to connect a device to the TV, make before making any connection. After the connection is done, you can turn on the units and use them.

Other Connections

If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them.

Connector	Type	Cables	Device

COMPONENT

AUDIO IN

| VGA/ Component Audio Connection (back)| Component GA Audio Cable

SPDIF

| SPDIF
(Optical Out) Connection (back)| DAEWOO 32DM54HA Colour Television with
Remote Control - Cables 4 |

COMPOSITE

| Composite
(Audio Nidec) Connection (back)| DAEWOO 32DM54HA Colour Television with
Remote Control - Cables 5 Audio Video Cable|

HEADPHONE

LAN

| Ethernet
Connection (back)| LAN / Ethernet Cable|

To enable VGA/Component audio, you will needtouse the back audio inputs with a VGA/Component audio cable for audio connection.
When using the wall! mounting kit (contact your dealer to purchase one, if not supplied), we recommend that you plug aft your cables into the back of the TV before mounting on the wall, insert or remove the Ci module only when the TV is SWITCHED OFF. You should refer to the module instruction manual for defats of the settings. The USB inputs on the TV support devices up to 500mA.
Connecting devices that have current value above 500mA may damage your TV. When connecting equipment using a HDMI cable to your TV, to guarantee sufficient immunity against parasitic frequency radiation and trouble-free transmission of high Definition signals, such as 4K content, you have to use a high speed shielded (high grade) HDMI cable with ferrites,

Turning On/Off the TV

Connect power
IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket.
After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains.

Plug one end (the two-hole plug) of the supplied detachable power cord into the power cord inlet on the rear side of the TV as shown above. Then plug the other end of the power cord into the mains socket outlet. The TV will switch on automatically.
Note: on the model. To switch on the TV from standby If the TV is in standby mode the standby LED lights
up. To switch on the TV from standby mode either:

Press the Standby button on the remote control.
Press the control button on the TV.
The TV will then switch on.

To switch the TV into standby
The TV cannot be switched into standby mode via control button. Press and hold the Standby button on the remote control. dialogue will appear on the screen. Highlight OK and press the OK button. The TV will switch into standby mode.

To switch off the TV
To power down the TV completely, unplug the power cord from the mains socket.

Quick Standby Mode
In order to switch the TV into quick standby mode either;

Press the Standby button on the remote.
Press again to go back to operating mode.
Press the control button on the TV.
Press the control button again to go back to operating mode.

TV Control & Operation

The control button allows you to control the Quick Standby-On functions of the TV.
Note: on the model. Press the control button to turn the TV into quick standby mode.
The TV cannot be switched into standby mode via control button.
To turn on the TV: Press the control button, the TV will turn on.
Note: Live TV settings menu OSD in Live TV mode cannot be displayed via the control button.

Operation with the Remote Control
Press the Menu button on your remote control to display Live TV settings menu when in Live TV mode. Press Home button to display or return to the Home Screen of the Android TV. Use the directional buttons to move the focus, proceed, adjust some settings and press OK to make selections in order to make changes, set your preferences, enter a sub-menu, launch an application etc. Press Return/Back to return to the previous menu screen.

Input Selection
Once you have connected external systems to your Source button on your remote control consecutively or use the directional buttons and then press the OK mode. Or enter the Inputs menu on the Home Screen, select the desired source from the list and press OK.

Changing Channels and Volume
You can adjust the volume by using the Volume +/- buttons and change the channel in Live TV mode by using the Programme +/- buttons on the remote.

Remote Control

DAEWOO 32DM54HA Colour Television with Remote Control - Remote
Control

Inserting the Batteries into the Remote
Remove the screw that secures the battery compartment cover on the back side of the remote control first. Lift the cover gently. Insert two 1.5V – size AAA bat- terries. Make sure the (+) and (-) signs match (observe correct polarity). Bo not mix old and new batteries.
Replace only with same or equivalent type. Place the cover back on. Then screw the cover back on again.
Standby Button
Press and hold the Standby button on the remote control. Power off dialogue will appear on the screen.
Highlight OK and press the OK button. The TV will switch into standby mode. Press briefly and release to switch the TV into quick standby mode or to switch on the TV when in quick standby or standby mode.

Standby: Quick Standby / Standby / On
Numeric buttons: Switches the channel in Live TV mode, enters a number or a letter in the text box on the screen
Language: Switches among sound modes (analogue TV), displays and changes audio language (digital TV, where available)
Mute: Completely turns off the volume of the TV
Volume +/-
Guide: Displays the electronic programme guide in Live TV mode
Directional buttons: Navigates menus, setting options, moves the focus or cursor, etc. sets record time and displays the subpages in Live TV-Teletext mode when pressed Right or Left. Follow the on-screen instructions.
OK: Confirms selections, enters sub-menus, views channel list (in Live TV mode)
Back/Return: Returns to previous menu screen, goes one step back, closes open windows, closes teletext (in Live TV-Teletext mode)
Netflix: Launches the Netflix application
Google Play: Launches the Google Play Store application
Menu: Displays Live TV Settings menu (in Live TV mode), displays available setting options such as sound and picture
Rewind: Moves frames backwards in media such as movies
Stop: Stops the media being played
Record: Records programmes in Live TV mode
Coloured Buttons: Follow the on-screen instructions for coloured button functions
Pause: Pauses the media being played, starts time shift recording in Live TV mode Play: Starts to play selected media
Text: Opens and closes teletext (where available in Live TV mode)
Fast forward: Moves frames forward in media such as movies
MyButton1: Opens the picture mode setting menu on available sources
Prime Video: Launches the Amazon Prime Video application
YouTube: Launches the YouTube application
Exit: Closes and exits from Live TV Settings menus, closes the Home Screen, exits from any running application or menu or OSD banner, switches to last set source
Info: Displays information about on-screen content
Source: Shows all available broadcast and content sources, closes the Home Screen and switches to last set source
Programme +/-: Increases/Decreases channel number in Live TV mode
Home: Opens the Home Screen
Subtitles: Turns subtitles on and off (where available)

Initial Setup Wizard

Note: Follow the on-screen instructions to complete the initial setup process. Use the directional buttons and the OK button on the remote to select, set, confirm and proceed. When turned on for the first time, a welcome screen will be displayed. Select your language and press OK. Follow the on- screen instructions to setup your TV and install channels. The installation wizard will guide you through the setup process. You can perform initial setup anytime using the Reset option in the Settings>Device Preferences menu. You can access the Settings menu from the Home screen or from the TV options menu in Live TV mode.

Welcome Message and Language Selection
“Welcome” message will be displayed along with the language selection options listed on the screen. Select the desired language from the list and press OK to continue.
Initial Setup
After the language selection you can start the initial setup wizard. Highlight Continue and press OK to proceed. You will not be able go back and change the language once you proceed. If you need to change the language after this step you will have to switch the TV into standby mode so the setup process starts from the beginning when you next switch on the TV. In order to do this, press and hold the Standby button. A dialogue will be displayed. Highlight OK and press OK.
Search for accessories
A search for accessories will be performed after the initial setup has started. Follow the on-screen instructions to pair your remote control (depends on the model of the remote control) and other wireless accessories with your TV. Press Back/Return button to end adding accessories and proceed.
Quick Setup
If you didn’t priorly connect your TV to the internet via Ethernet a screen will be displayed where you can transfer your Android phone’s WLAN network and Google Account to your TV. Highlight Continue and press OK to proceed. Follow the on-screen instructions on your TV and your phone to complete the process. You can also skip this step by selecting Skip option. Some steps may be skipped depending on the settings made in this step. If you did priorly connect your TV to the internet via Ethernet a message will be displayed stating that you are connected. You can choose to continue with wired connection or change the network. Highlight Change network and press OK if you want to use wireless connection instead of wired connection.
Network Connection
You will be directed to the next step automatically, if you connect your TV to internet via Ethernet at this point. If not, available wireless networks will be searched and listed on the next screen. Select your WLAN network from the list and press OK to connect. Enter the password using the virtual keyboard if the network is password protected. Select the Other network option from the list, if the network that you want to connect has hidden SSID. If you prefer not to connect to the internet at this point you can skip this step by selecting Skip option. You can connect to internet later using the Network & Internet menu options in the Settings menu from the Home Screen or from the TV options menu in Live TV mode.
This step will be skipped if internet connection has been established in the previous step.
Sign in to your Google account
If connection succeeds, you can sign in to your Google account on the next screen. You need to be signed in to a Google account in order to use Google services. This step will be skipped if no internet connection has been established in the previous step or if you already signed in to your Google account in Quick Setup step. By signing in, you will be able to discover new apps for videos, music and games on Google Play; get personalised recommendations from apps like YouTube; buy or rent the newest movies and shows on Google Play Movies & TV; access your entertainment and control your media. Highlight Sign In and press OK to proceed. Sign-in options are as following:
• Use your phone or computer: You can use a browser on your phone or computer to sign in. Highlight this option and press OK button. A code will be displayed on the TV screen. Make sure your phone or computer is on the same network as your TV. Open the given website (androidtv.com/setup, follow on-screen instructions for the up-to-date website url) in your phone’s or computer’s browser and enter the code you see on your TV screen into the related entry field. Then follow the instructions on your device and complete the process.
• Use your remote: Using this option you can sign in to your Google account by entering your e-mail address or phone number and your password. If you prefer not to sign in to your Google account at this point you can skip this step by selecting Skip option.
Terms of Service Terms of Service screen will be displayed next. By continuing, you will agree to the Google Terms of Service, the Google Privacy Policy and the Google Play Terms of Service. Highlight Accept and press OK on the remote to confirm and proceed. You can also view Terms of Service, Privacy Policy and Play Terms of Service on this screen. To display the content an internet connection is needed. A message will be displayed mentioning the web site address on which this information can also be viewed, in case internet access is not available.
Location
On the next screen, you can allow or disallow Google and third party apps to use your TV’s location informa-tion. Select Yes to confirm and press OK. To skip this step without confirmation, select No and proceed by pressing the OK button. You can change this setting later using the Settings>Device Preferences>Loca-tion menu on the Home Screen.
Help improve Android
Automatically send diagnostic information to Google, like crash reports and usage data from your device and apps. This information won’t be used to identify you. Select Yes to confirm and press OK. To skip this step without confirmation, select No and proceed by pressing the OK button. You can change this setting later using the Settings>Device Preferences>Usage & Diagnostics menu on the Home Screen. Information on Google services and some features of your TV will be displayed next. You can turn on person-al results for Assistant by choosing the related option when prompted. Press OK consecutively to proceed.
Country
In the next step select your Country from the list and press OK to continue.
Password
Depending on the country selection you made in the previous step you may be asked to define a password (PIN) at this point. Press OK to proceed. The selected PIN cannot be 0000. This PIN will be required in order to access some menus, contents or to release locked channels, sources etc. You will have to enter it if you are asked to enter a PIN for any menu operation later.
Select TV Mode
In the following step of the initial setup, you can set the TV’s operation mode either as Home or as Store. Store option will configure your TV’s settings for store environment. This option is intended only for store use. It is recommended to select Home for home use.
Chromecast built-in always available
Select your Chromecast availability preference. If set as On your TV will be detected as a Google Cast device and allow Google Assistant and other services to wake your TV up to respond to Cast commands, even when on standby mode and the screen is off.
Tuner Mode
Note: If you don’t want to perform a tuner scan, select one of the available options anyway. You can skip the scan at some later stage of the installation wizard. If you skip this step you can perform a channel search later using the related Channels menu options. The next step is the selection of the tuner mode. Select your tuner preference to install channels for Live TV function. Antenna, Cable and Satellite options are available. Highlight the option that corresponds to your environment and press OK or Right directional button to proceed.

Antenna
If Antenna option is selected, the TV will search for digital terrestrial and analogue broadcasts. On the next screen highlight Scan option and press OK to start the search or select Skip Scan to continue without performing a search. Note: If the country selected does not have analogue broadcasts, the analogue search option may not be available.
Cable
If Cable option is selected, the TV will search for digital cable and analogue broadcasts. If any, available operator options will be listed on the Select Operator screen. Otherwise this step will be skipped. You can select only one operator from the list. Highlight the desired operator and press OK or the Right directional button to proceed. On the next screen select Scan option to start a search or select Skip Scan to continue without performing a search. If Scan is selected a configuration screen will be displayed next. Scan Mode, Frequency(KHz), Modulation, Symbol Rate(Ksym/s), Network ID options may need to be set. To perform a full scan set the Scan Mode as Full/Advance if available. Depending on the selected operator and/or Scan Mode some options may not be available to be set.
Note: If the country selected does not have analogue broadcasts, the analogue search option may not be available. Once you are done with setting available options, press the Right directional button to proceed. The TV will start to search available broadcasts.
Satellite
If Satellite option is selected, Satellite Type screen will be displayed next. Preferred Satellite and General Satellite options will be available. Select one and press OK to proceed.
Note: Preferred Satellite and General Satellite options may not be available depending on the selected country. In this case the DVBS Configuration Setting screen will be displayed after selecting the tuner mode as Satellite. If Preferred Satellite option is selected, next screen will be Select Operator screen. You can select only one operator from the list. Highlight the desired operator and press OK or the Right directional button to proceed. Some of the following options may be preset depending on the selected operator in this step. Check the parameters before proceeding and adjust if necessary.
DVBS Configuration Setting screen will be displayed next. First Antenna type() should be set. Universal, Single Cable and Jess Singlecable options are available. Set the Antenna Type as Universal for Direct and DiSEqC satellite systems.
If you set the antenna type as Universal, press the Right directional button to proceed to the next step. If the antenna type is set as Single Cable or Jess Singlecable, there will be three more additional options on the DVBS Configuration Setting screen: Tuner, Band frequency and User Defined. User Defined option will be available if the Band frequency is set as User Defined. Set these options if available and press the Right directional button to proceed. () This option may be named as Satellite type depending on the country selection. Depending on the country and satellite type selections you made in the earlier steps of the initial setup process, Load Preset List screen may be displayed next. Highlight Load Preset List and press OK or the Right directional button to proceed with the SatcoDX installation. You can also skip this step by selecting Skip option. After the parameters on the DVBS Configuration Setting screen are configured according to your environment and preset list installation preference is selected the next step may be Select Satellite screen. You may be able to set up different satellites depending on the selected antenna type and operator in the previous steps.
Highlight the desired satellite option and press OK to set the parameters(). The Satellite Status of the first satellite option will be set as On. In order to configure other settings of the satellite and to enable scan this option should be set as On first. Press Back button and select next satellite you want to set. After you completed the configuration changes, press the Right directional button to proceed. () If you have a Direct satellite system, DiSEqC Set option should be set as DiSEqC A. If Load Preset List option is selected in the previous step next steps will be skipped and the preset channel list installation will start. If the correct satellite has not been selected for SatcoDX installation, a warning dialogue will be displayed on the screen. The satellite/s that can be selected will be listed. Press OK to close the dialogue and then set the satellite accordingly.
Channel Scan screen will be displayed next. Select Scan and press OK or the Right directional button to proceed with the scanning configurations. Select Skip Scan to proceed without performing a scan and complete the initial setup. DVBS Scan Configure screen will be displayed next if Scan option is selected. Following options will be available: Scan Mode and Channels. You can choose to perform a full scan or a network scan. Set the Scan Mode accordingly. If you are going to perform a network scan, make sure that you have adjusted the Frequency, Symbol Rate (Kym/s) and Polarization parameters under the Transponder option accurately on the Satellite Setup screen. You may not be able to change the Scan mode setting depending on the previous selections. If the Channels option is set as Free encrypted channels will not be installed. Additional options may also be available depending on the selected operator, configure these settings according to your preferences. Once you are done with setting the available options, press the Right directional button to start scan while Scan Mode or Channels is highlighted. While the search continues you can press the Back button to cancel the search. The channels that have already been found will be stored in the channel list.
When the initial setup is completed results will be displayed. Press OK to finish the setup. Home Screen will be displayed. You can press the Exit button on the remote or highlight the Live TV app from the Apps row on the Home Screen and press OK to switch to Live TV mode and watch TV channels. For some countries, the Live TV app will be situated in the Home tab on the Home Screen and the row with this app will be named as Favorite Apps.

Home Screen

To enjoy the benefits of your Android TV, your TV must be connected to the Internet. Connect the TV to a home network with a high-speed Internet connection. You can connect your TV wirelessly or wired to your modem/router. Refer to the Network & Internet and Connecting to the Internet sections for further information on how to connect your TV to the internet. The Home menu is the centre of your TV. Press the Home button to display Home Screen. From the Home menu you can start any application, switch to a TV channel, watch a movie or switch to a connected device. Depending on your TV setup and your country selection in the initial setup the Home menu may contain different items.
The available options of the Home Screen are positioned in rows. To navigate through the Home Screen options use the directional buttons on the remote. Apps, YouTube, Google Play Movies & TV, Google Play Music and Google Play related rows and rows of the applications you have installed might be available. Select a row then move the focus to the desired item in the row. Press OK button to make a selection or to enter a sub-menu.
On the upper left of the screen, search tools will be located. You can choose either to type a word to start a search via the virtual keyboard or try voice search option if your remote has a built-in microphone.
Move the focus to the desired option and press OK to proceed. On the upper right of the screen, Notifications, Inputs, Network & Internet (will be named as Connected or Not Connected according to the current connection status), Settings and the current time will be displayed. You can configure your date and time preferences using the Date & time menu options from the Settings>Device Preferences menu. First row will be the Apps row. Live TV and Multi Media Player apps will be available alongside with other apps. Highlight Live TV and press OK to switch to Live TV mode. If the source was set to an option other than TV previously, press the Source button and set as TV in order to watch live TV channels. Highlight Multi Media Player and press OK to browse the connected USB devices and play/display the installed media content on the TV. The audio can be played through the speakers of the TV or through the speaker systems connected to the TV. You can configure your sound output preference from the Speakers option in the Settings>Device Preferences>Sound menu. To browse the internet, you will need an internet browser application. Make a search or launch the Google Play app, find a browser and download it. For some countries, the Home Screen will be organized into several tabs. Home, Discover and Apps tabs will be available. You can scroll through the tabs using the directional buttons. Each tab will have a featured content row at the top. In the Home tab, there will be rows for favorite apps, recent Live TV programmes and recommendations from streaming apps. In the Discover tab recommendations from streaming services will be displayed. In the Apps tab, all the apps installed on your TV will be displayed and you can install more from Play Store using the related option. Depending on your TV setup and your country selection in the initial setup, the tabs on the Home Screen may contain different items.

Switch the TV to Live TV mode first and then press the Menu button on the remote to see Live TV menu options. To switch to Live TV mode you can either press the Exit button or highlight the Live TV app from the Apps row on the Home Screen and press OK. For some countries, the Live TV app will be situated in the Home tab on the Home Screen and the row with this app will be named as Favorite Apps.

Channels
Add to My Favorites: Add the channel that is currently being watched to the previously selected favorite list.
Add to My Favorite’s : Add the channel that is currently being watched to the previously selected favorite list.
Programme Guide: Open the electronic programme guide. Refer to the Programme Guide section for detailed information. New Channels Available: Start a search for new channels. Select the channel source application or tuner. Then make the settings according to your environment and preferences if necessary. You can use the Channel menu options to search for broadcast channels. Refer to the Channel section for more information. When complete highlight Done and press OK.

TV Options
Source: Display the list of input sources. Select the desired one and press OK to switch to that source. Picture Mode: Set the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: User, Standard, Vivid, Sport, Movie and Game. You can use User mode to create customized settings. Go to Settings>Device Preferences>Picture for detailed setting options. Display Mode: Set the aspect ratio of the screen. Select one of the predefined options according to your preference. Speakers: To hear the TV audio from the connected compatible audio device set as External Audio System. Set as TV Speakers to use the speakers of your TV for sound output.
Power
Picture off: Select this option and press OK to turn the screen off. Press a button on the remote or on the TV to turn the screen on again. Note that you can not turn the screen on via the Volume +/-, Mute and Standby buttons. These buttons will function normally. No Signal Auto Power Off: Set the behaviour of the TV, when no signal is detected from the currently set input source. Define a time after which you want your TV to turn itself off or set as Off to disable.
CI Card: Display available menu options of the CI card in use. This item may not be available depending on the input source setting. Advanced Options Audio Language: Set your language preference for audio. This item may not be available depending on the input source setting. Blue Mute: Turn this function on/off according to your preference. When turned on, blue background will be displayed on the screen when no signal is available.
Default Channel: Set your default startup channel preference. When the Select Mode is set as User Select, Show Channels option will become available. Highlight and press OK to see channel list. Highlight a channel and press OK to make a selection. Selected channel will be displayed, every time the TV is turned back on from any standby mode. If the Select Mode is set as Last Status, the last watched channel will be displayed. Interaction Channel: Turn the Interaction Channel function on or off. This feature is useful in the UK and Ireland only. MHEG PIN Protection: Turn the MHEG PIN protection function on or off. This setting enables or disables access some of the MHEG applications. Disabled applications can be released by entering the right PIN. This feature is useful in the UK and Ireland only. HBBTV Settings HBBTV Support: Turn the HBBTV function on or off.
Do Not Track : Set your preference regarding the tracking behaviour for HBBTV services. Cookie Settings: Set your cookie setting preference for HBBTV services. Persistent Storage: Turn the Persistent Storage function on or off. If set as On cookies will be stored with an expiry date in the persistent memory of the TV. Block Tracking Sites: Turn the Block Tracking Sites function on or off.
Device ID: Turn the Device ID function on or off.
Reset Device ID: Reset the device ID for HBBTV services. Confirmation dialogue will be displayed. Press OK to proceed, Back to cancel.
Subtitle
Analogue Subtitle: Set this option as Off, On or Mute. If Mute option is selected, the analogue subtitle will be displayed on the screen but the speakers will be muted simultaneously. Digital Subtitle: Set this option as Off or On.
Subtitle Tracks: Set your subtitle track preference, if any available. Digital Subtitle Language: Set one of the listed language options as first digital subtitle language preference. Second Digital
Subtitle Language: Set one of the listed language options as second digital subtitle language preference. If the selected language in the Digital Subtitle Language option is not available, the subtitles will be displayed in this language. Subtitle
Type: Set this option as Normal or Hearing Impaired. If Hearing Impaired option is selected, it provides subtitle services to deaf and hard of hearing viewers with additional descriptions.
Teletext
Digital Teletext Language: Set the teletext language for digital broadcasts.
Decoding Page Language: Set the decoding page language for teletext display.
BISS Key: “Click To Add Bass Key” message will be displayed. Press OK button to add a bass key. Frequency, Symbol Rate (Kym/s), Polarization, Programme ID and CW Key parameters will be available to be set. Once you are done with the settings highlight Save Key and press OK to save and add the bass key. This option will not be available if the Channel Installation Mode under the Settings>Channel menu is not set as Preferred Satellite, General Satellite or Satellite. Available options will differ depending on the selected country during the initial setup process.
Auto Sleep: Define an idle time after which you want your TV to enter sleep mode automatically. 4 Hours, 6 Hours and 8 Hours options are available. Set as Never to disable.
System Information: Display detailed system information on the current channel such as Signal Level, Signal Quality, Frequency etc. Version Info: Display system information such as Model Name and Version.
Settings: Refer to Settings section for detailed information.
Record
Record List: The recordings will be displayed if any available. Highlight a recording of your choice and press the Yellow button to delete it or press the Blue button to view detailed information. You can use Red and Green buttons to scroll the page up and down.
Device Info: Connected USB storage devices will be displayed. Highlight the device of your choice and press OK to see available options.
Set Time Shift: Tag the selected USB storage device or a partition on it for time shift recording.
Set PVR: Tag the selected USB storage device or a partition on it for PVR. Format: Format the selected USB storage device. Refer to USB Recording section for more information Speed Test: Start a speed test for the selected USB storage device. The test result will be displayed when completed. Schedule List: Add reminders or record timers using the Schedule List menu.
Time Shift Mode: Enable or disable time shift recording feature. Refer to USB Recording section for more information.

Settings

You can access the Settings menu from the Home Screen or from the TV options menu in Live TV mode.

Network & Internet
You can configure your TV’s network settings using the options of this menu. You can also highlight the Connected/Not Connected icon on the Home screen and press OK to access this menu. Wi-Fi: Turn the wireless LAN (WLAN) function on and off.

Available networks
When the WLAN function is turned on, available wireless networks will be listed. Highlight See all and press OK to see all networks. Select one and press OK to connect. You may be asked to enter a password to connect to the selected network, in case the network is password protected.

Other options
Add new network: Add networks with hidden SSID’s.
Scanning always available: You can let the location service and other apps scan for networks, even when WLAN function is turned off. Press OK to turn it on and off. Wow: Turn this function on and off. This function allows you to turn on or awaken your TV via wireless network. Wool: Turn this function on and off. This function allows you to turn on or awaken your TV via network.

Ethernet
Connected/Not connected: Displays the status of the internet connection via Ethernet, IP and MAC addresses.
Proxy settings: Set a HTTP proxy for browser Manu-ally. This proxy may not be used by other apps.
IP settings: Configure your TV’s IP settings.

Channel
Channels
Options of this menu may change or become inactive depending on the Channel Installation Mode selection.

Channel Installation Mode – Antenna
Automatic Channel Search: Start a scan for analogue and digital channels. You can press the Back button to § cancel the scan. The channels that have already been g- found will be stored in the channel list.
Update Scan: Search for updates. Previously added channels will not be deleted, but any newly found channels will be stored in the channel list.
Analogue Manual Scan: Start a manual scan for analogue channels. Enter the Start Frequency and then select Scan Up or Scan Down. When a channel is found the scan will be completed and the found channel will be stored in the channel list.
Single RF Scan: Select the RF Channel by using the Right/Left directional buttons. Signal Level and Signal Quality of the selected channel will be shown. Press OK to start scan on the selected RF channel. The found channels will be stored in the channel list. Manual Service Update: Start a service update manually. LCN: Set your preference for LCN. LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel number sequence (if available). Channel Scan Type: Set your scan type preference. Channel Store Type: Set your store type preference. Favourite Network Select: Select your favourite network. This menu option will be active, if more than one network is available.
Channel Skip: Set channels to be skipped when switching the channels via Programme +/- buttons on the remote. Highlight the desired channel/s on the list and press OK to select/unselect.
Channel Swap: Replace the positions of the two selected channels in the channel list. Highlight the desired channels on the list and press OK to select. When the second channel is selected, the position of this channel will be replaced with the position of the first selected channel. You should set the LCN option to Off or Default in order to enable this feature.
Channel Move: Move a channel to the position of another channel. Highlight the channel you want to move and press OK to select. Then do the same for a second channel. When the second channel is selected, the first selected channel will be moved to the position of that channel. You should set the LCN option to Off or Default in order to enable this feature.
Channel Edit : Edit channels in the channel list. Edit the name and channel number of the selected channel and display Network Name, Frequency, Colour System and Sound System information related to that channel if available. Depending on the channel other options may also be editable. You can press the Blue button to delete the highlighted channel. Analogue Channel Fine-tune: Fine-tune an analogue channel. A list of available analogue channels will be displayed. Select the desired one from the list and press OK button. Then change the frequency of the channel by pressing Left/Right directional buttons. Press OK to store the new frequency for that channel. Press Back to cancel. This item may not be visible,
depending on whether or not the last watched channel was analogue. Clear Channel List: Delete all channels stored in the channel list of the selected channel installation mode. A dialogue will be displayed for confirmation. Highlight OK and press OK button to proceed. Highlight Cancel and press OK to cancel.

Channel Installation Mode – Cable
Automatic Channel Search: Start a scan for analogue and digital cable channels. If available, operator op-tions will be listed. Select the desired one and press OK. Scan Mode, Channel Scan Type, Frequency and Network ID options may be available. The options may vary depending on the operator and the Scan Mode selections. Set the Scan Mode as Full if you don’t know how to set up other options. Highlight Scan and press OK to start the scan. You can press the Back button to cancel the scan. The channels that have already been found will be stored in the channel list. Single RF Scan: Enter the Frequency value. Signal Level and Signal Quality of the selected Frequency will be shown. Highlight the Scan option and press OK to start scan. The found channels will be stored in the channel list.
LCN: Set your preference for LCN. LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel number sequence (if available).
Channel Scan Type: Set your scan type preference.
Channel Store Type: Set your store type preference.
Favorite Network Select: Select your favorite net-work. This menu option will be active, if more than one network is available. This option may not be available depending on the selected country during the initial setup process.
Channel Skip : Set channels to be skipped when switching the channels via Programme +/- buttons on the remote. Highlight the desired channel/s on the list and press OK to select/unselect.
Channel Swap: Replace the positions of the two selected channels in the channel list. Highlight the desired channels on the list and press OK to select. When the second channel is selected, the position of this channel will be replaced with the position of the first selected channel. You should set the LCN option to Off or Default in order to enable this feature.
Channel Move: Move a channel to the position of another channel. Highlight the channel you want to move and press OK to select. Then do the same for a second channel. When the second channel is selected, the first selected channel will be moved to the position of that channel. You should set the LCN option to Off or Default in order to enable this feature.
Channel Edit: Edit channels in the channel list. Edit the name and channel number of the selected channel and display Network Name, Frequency, Colour Sys-tem, Sound System, Modulation and Symbol Rate information related to that channel. Depending on the channel other options may also be editable. You can press the Blue button to delete the highlighted channel.
Analogue Channel Fine-tune: Fine-tune an analogue channel. A list of available analogue channels will be displayed. Select the desired one from the list and press OK button. Then change the frequency of the channel by pressing Left/Right directional buttons. Press OK to store the new frequency for that channel. Press Back to cancel. This item may not be visible, depending on whether or not the last watched channel was analogue. Clear Channel List: Delete all channels stored in the channel list of the selected channel installation mode. A dialogue will be displayed for confirmation. Highlight OK and press OK button to proceed. Highlight Cancel and press OK to cancel.

Channel Installation Mode – Preferred/General Satellite/Satellite
Satellite Re-scan: Start a satellite scan beginning with the operator selection screen for the Preferred Satellite channel installation mode or with the satellite selection screen for the General Satellite or Satellite channel installation mode. When this scanning option is preferred, some scanning configurations will not be available and thus the preferences you made during the initial setup process may not be changed.
Satellite Add: Add satellite and perform a satellite scan.
Satellite Update: Search for any updates by repeating the previous scan with the same settings. You will also be able to configure these settings before the scan. If Channel Installation Mode is set to Preferred Stael-lite this option may be named differently depending on the available services. Highlight the satellite and press OK button to configure detailed satellite parameters. Press the Right directional button to proceed. Satellite Manual Tuning: Start a manual satellite scan. Favourite Network Select: Select your favorite net-work. This menu option will be active, if more than one network is available. This option may not be available depending on the selected country during the initial setup process.
Channel Skip: Set channels to be skipped when switching the channels via Programme +/- buttons on the remote. Highlight the desired channel/s on the list and press OK to select/unselect.
Channel Swap: Replace the positions of the two selected channels in the channel list. Highlight the desired channels on the list and press OK to select. When the second channel is selected, the position of
this channel will be replaced with the position of the first selected channel.
Channel Move: Move a channel to the position of another channel. Highlight the channel you want to move and press OK to select. Then do the same for a second channel. When the second channel is selected, the first selected channel will be moved to the position of that channel.
Channel Edit: Edit channels in the channel list. Edit the name and channel number of the selected channel and display Network Name, Frequency, Colour System and Sound System information related to that channel if available. Depending on the channel other options may also be editable. You can press the Blue button to delete the highlighted channel. Clear Channel List: Delete all channels stored in the channel list of the selected channel installation mode. A dialogue will be displayed for confirmation. Highlight OK and press OK button to proceed. Highlight Cancel and press OK to cancel. Note: Some options may not be available and appear as grayed out depending on the operator selection and operator related settings.

Channel Installation Mode
Set this option as Antenna, Cable, Preferred Satel-lite, General Satellite or Satellite.

Auto Channel Update
Turn the auto channel update function on or off.

Channel Update Message
Turn the channel update message function on or off. This item may not be visible, depending on the Chan-nel Installation Mode selection.

Parental Controls
(*) To enter this menu PIN should be entered first. Default PIN is set to 1234. If you have defined a new PIN after the initial setup process use the PIN that you have defined. Some options may not be available or vary depending on the country selection during the initial setup.
Channels Blocked: Select channel/s to be blocked from the channel list. Highlight a channel and press OK to select/unselect. To watch a blocked channel PIN should be entered first.
Programme Restrictions: Block programmes according to the age rating information that is being broad-casted with them. You can turn on or off restrictions, set rating systems, restriction levels and age limits using the options of this menu.
Inputs Blocked: Prevent access to the selected input source content. Highlight the desired input option and press OK to select/unselect. To switch to a blocked input source PIN should be entered first.
Change PIN: Change the default PIN. Highlight this option and press OK. You will need to enter the old PIN first. Then new PIN entry screen will be displayed. Enter the new PIN twice for confirmation.

Audio Channel
Set the audio channel preference, if available. This item may not be visible, depending on whether or not the last watched channel was analogue.

Audio Language
Set one of the listed language options as first audio language preference. This item may not be visible, depending on whether or not the last watched channel was digital.

Second Audio Language
Set one of the listed language options as second audio language preference. If in the Audio Language setting selected language option is not supported, this language preference will be considered. This item may not be visible, depending on whether or not the last watched channel was digital.

Open Source Licenses
Display Open Source Software license information.

Version
Displays system version number.

Accounts & Sign In
Google: This option will be available if you have signed in to your Google account. You can configure your data syncing preferences or remove your registered account on the TV. Highlight a service listed in the Choose synced apps section and press OK to enable/disable data sync. Highlight Sync now and press OK to sync all enabled services at once.
Add account: Add a new one to available accounts by signing in to it.

Apps
Using the options of this menu, you can manage the apps on your TV.

Recently opened apps
You can display recently opened apps. Highlight See all apps and press OK to see all the apps installed on your TV. The amount of storage space that they needed will also be displayed. You can see the version of the app, open or force to stop the running of the app, uninstall a downloaded app, see the permissions and turn them on/off, turn on/off the notifications, clear the data and cache etc. Highlight an app and press OK to see available options.

Permissions
Manage the permissions and some other features of the apps. App permissions: The apps will be sorted by permission type categories. You can enable disable permissions for the apps from within these categories.
Special app access: Configure some app features and special permissions. Security & restrictions: Using the options of this menu;

You can allow or restrict installation of apps from sources other than the Google Play Store.
Set the N to disallow or warn before installation of apps that may cause harm.

Device Preferences
About: Check for system updates. change the device name, restart the TV and display system information such as network addresses. serial numbers. versions etc. You can also display legal information, manage advertisings, display your advertising ID, reset it and tum on/off the personalised advertisings based on your interests.
Netflix ESN: Display your ESN number. ESN number is an unique ID number for Netflix, created especially to identify your TV.
Date & time: Set the date and time options of your TV. You can set your N to automatically update the time and date data over the network or over the broadcasts. Set corresponding to your environment and preference. Disable by setting as Off if you want to manually change the date or time. Then set date, time, time zone and hour format options.

Timer
Power On Time Type: Set your N to turn on by itself. Set this option as On or Once to enable a power on timer to be set, set as Off to disable. If set as Once the will turn on only once at the defined time in Auto Power On Time option below. Auto Power On lime: Available if the Power On Time Type is enabled. Set the desired time for your N to come on from standby using the directional buttons and press OK to save the new set time. Power Off Time Type: Set your TV to turn off by itself. Set this option as On or Once to enable a power off timer to be set, set as Off to disable. If set as Once the TV will turn off only once at the defined time in Auto Power Off Time option below. Auto Power Off Time: Available if the Power Off Time type is enabled. Set the desired time for your TV to go to standby using the directional buttons and press OK to save the new set time.
Language: Set your language preference.
Keyboard: Select your keyboard type and manage keyboard settings.
Inputs: Show or hide an input terminal, change the label for an input terminal, and configure the options for HDMI CEC(Con summer Electronic Control) function and display the CEC device list.
Power
Picture off: Select this option and press OK to turn the screen off. Press a button on the remote or on the TV to tum the screen on again.
Note that you can not turn the screen on via the Volume +1-, Mute and Standby buttons. These buttons will function normally.
No Signal Auto Power Off: Set the behaviour of the N, when no signal is detected from the currently set input source. Defi ne a time after which you want your N to turn itself off or set as Off to disable.

Picture
Picture Mode: Set the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: User, Standard, Vivid, Sport, Movie and Game. You can use User mode to create customised settings.
Backlight, Brightness, Contrast, Colour, Hue, Sharpness settings will be adjusted according to the selected picture mode. If one of these settings is changed manually, Picture Mode option will be changed to User, if not already set as User. Auto Backlight: Set your auto backlight preference. Off, Low, Middle and Eco options will be available. Set as Off to disable.
Backlight: Adjust the backlight level of the screen manually. This item will not be available if the Auto Backlight is not set as Off.
Brightness: Adjust the brightness value of the screen.
Contrast: Adjust the contrast value of the screen.
Colour: Adjust the colour saturation value of the screen. Hue: Adjust the hue value of the screen.
Sharpness: Adjust the sharpness value for the objects displayed on the screen.
Gamma: Set your gamma preference. Dark, Middle and Bright options will be available.
Colour Temperature: Set your colour temperature preference. User, Cool, Standard and Warm options will be available. You can adjust red, green and blue gain values manually. If one of these values is changed manually, Colour Temperature option will be changed to User, if not already set as User.
Display Mode: Set the aspect ratio of the screen. Select one of the predefined options according to your preference. HDR: Turn the HDR function on or off. This item will be available if HDR content is detected.
Advanced Video DNR: Dynamic Noise Reduction (DNR) is the process of removing noise from digital or analogue signal. Set your DNR preference as Low, Medium, Strong. Auto or turn it off by setting as Off.
MPEG NR: MPEG Noise Reduction cleans up block noise around outlines and noise on the back-ground. Set your MPEG NR preference as Low. Medium, Strong or turn it off by setting as Off.
Adaptive Lama Control: Adaptive Lama control adjusts contrast settings globally according to content histogram in order to provide deeper black and brighter white perception. Set your Adaptive Lama Control preference as Low, Medium, Strong or turn it off by setting as Off. DI Film Mode: It is the function for 3:2 or 22 cadence detection for 24 fps film contents and improves the side effects (like interlacing effect or judder) which are caused by these pull down methods. Set your DI Film Mode preference as Auto or turn it off by setting as Off. This item will not be available if Game Mode or PC Mode is timed on.
Blue Stretch: Human eye perceives coolerwhites as brighter white, Blue Stretch feature changes White balance of mid-high grey levels to cooler colour temperature. Tum the Blue Stretch function on or off. Game Mode: Game mode is the mode which cuts down some of the picture processing algorithms to keep up with video games that have fast frame rates. Turn the Game Mode function on or off.
PC Mode: PC Mode is the mode which cuts down some of the picture processing algorithms to keep signal type as it is. It can be usable especially for RGB inputs. Turn the PC Mode function on or off. HDMI RGB Range: This setting should be adjusted according to input RGB signal range on HDMI source. It can be limited range (16-235) or full range (0-255). Set your HDMI RGB range preference. Auto. Full and Limit options will be available. This item will not be available, if the input source is not set as HDMI.
Colour Tuner: Colour saturation, hue, brightness can be adjustable for red, green, blue, cyan, ma-gnat, yellow and flesh tone (skin tone) for having more vivid or more natural image. Set the Hue, Colour, Brightness, Offset and Gain values
manually. Highlight Enable and press OK to turn this function on. 11 Point White Balance Correction: White balance feature calibrates TV’s colour temperature in detailed grey levels. By visually or measurement. grey scale uniformity can be improved. Adjust the strength of the Red, Green, Blue colors and Gain value manually. Highlight Enable and press OK to turn this function on. Reset to Default
• Reset the video settings to factory default settings.
Note: Depending on the currently set input source some menu options may not be available. Sound System Sounds: System sound is the sound played when navigating or selecting an item on the TV screen. Highlight this option and press OK to turn this function on or off.
Sound Style: For easy sound adjustment, you can select a preset setting. User, Standard, Viv-id. Sport, Movie. Music or News options will be available. Sound settings will be adjusted according to the selected sound style. Some other sound options may become unavailable depending on the selection. Balance: Adjust the left and right volume balance for speakers and headphones.
Equalizer Detail: Adjust the equalizer values ac-cording to your preferences.
Speakers: To hear the TV audio from the connected compatible audio device set as External Audio System. Set as N Speakers to use the speakers of your TV for sound output. Digital Output: Set the digital sound output preference. Auto, Bypass, PCM, Dolby Digital Plus and Dolby Digital options will be available. Highlight the option you prefer and press OK to set. SPDIF Delay: Adjust the SPDIF delay value.
Auto Volume Control: With Auto Volume Control, you can set the TV to automatically level out sudden volume differences. Typically at the beginning of adverts or when you are switching channels. Tum this option on/off by pressing OK.
Downmix Mode: Set your preference to convert mul-ti-channel audio signals to two-channel audio signals. Press OK to see the options and set. Stereo and Surround options will be available. Highlight the option you prefer and press OK to set.
Dolby Audio Processing: With Dolby Audio Pro-cissing, you can improve the sound quality of your TV. Press OK to see the options and set. Some other sound options may become unavailable and appear as grayed out depending on the settings made here.
Dolby Audio Processing: Highlight this option and press OK Sound Mode: If the Dolby Audio Processing option is turned on Sound Mode option will be available to set. Highlight the Sound Mode option and press OK to see the preset sound modes.
Smart, Movie, Music and News options will be available. Highlight the option you prefer and press OK to set.
Reset to Default: Resets the sound settings to factory defaults.

Storage: View the total storage space status of the TV and connected devices if available. To see detailed information on the usage details highlight and press OK. There will also be options for ejecting and formatting the connected storage devices.
Home screen: Customise your Home Screen. Select channels which will be displayed on the Home Screen, enable/disable video and audio previews. Organise apps and games, change their order or get more of them. Display open source licences.
For some countries, the Home Screen will be organised into several tabs and this menu will contain additional options to customise the content of these tabs. Highlight Set up and press OK to sign in to a Google account, so you can browse personalised recommendations for that account in the Discover tab on the Home Screen. After signing in, using the related options in this menu, you can view your account activity controls and permissions, customise recommendations.
Store mode: Highlight Store mode and press OK. Highlight Continue and press OK if you want to proceed. Then highlight On to activate or to deactivate and press OK. In store mode your TV’s settings will features will be displayed on the screen. Once activated, Store messaging setting will become available. Set according to your preferences. It is recommended not to activate store mode for home use.
Google Assistant: Select your active account, view permissions, select which apps to include in search word blocking and view open source licenses. Screen saver: Set screensaver and sleep mode options for your TV. You can choose a screensaver, set wait time for the screensaver, set when the TV goes into sleep mode or start the screensaver mode.
Location: You can allow the use of the wireless connection to estimate the location, see the recent location requests and allow or restrict the listed apps to use your location information.
Usage & Diagnostics: Automatically send usage data and diagnostic information to Google. Set according to your preference.
Manufacturer Usage & Diagnostics: If you accept, your TV will send diagnostic information (such as MAC versions, bootloader versions and the source of the TV) and anonymous usage data from your device to a server located in Ireland. We are not able to identify you and are only collecting and storing this diagnostic information and anonymous usage data to ensure your device operates properly.
Accessibility: Visually Impaired, Captions settings and/or turn Audio Description, Hearing Impaired, Spoken subtitle, High contrast text on/off. Some the caption settings may not be append.
Visually Impaired: Digital TV channels can broadcast special audio commentary describing on-screen action, body language, expressions and movements for people with visual disabilities.
Speaker: Turn this option on if you want to hear the audio commentary through the TV speakers.
Headphone: Turn this option on if you want to route the sound of the audio commentary to the TV’s headphone output.
Volume: Adjust the volume level of the audio commentary.
Pan and Fade: Turn this option on if you want to hear the audio commentary more clearly, when it is available through broadcast.
Audio for the Visually Impaired: Set the audio type for visually impaired. Options will be available depending on the selected broadcast.
Fader Control: Adjust the volume balance between the main TV audio (Main) and audio commentary (AD).
Reset: Reset all TV settings to the factory default.
Highlight Reset and press OK will be displayed, select Erase everything to proceed initial setup will start. Select Cancel to exit.
Note: You may be asked to enter a PIN to proceed with the stallation, you can use the default PIN. The default PIN is 1234.

Remote & Accessories
You can use wireless accessories, such as your remote control (depends on the model of the remote control), headphones, keyboards or game controllers with your Android TV. Add devices to use them with your TV. Select this option and press OK to start searching available devices in order to pair them with your TV. If available highlight Add accessory option and press OK to start the search. Set your device to pairing mode. Available devices will be recognized and listed or pairing request will be displayed. Select your device from the list and press OK or highlight OK and press OK to start pairing.
Connected devices will also be listed here. To unpair a device, highlight it and press OK. Then highlight Unpair option and press OK. Then select OK and press OK again to unpair the device from the TV. You can also change the name of an connected device. Highlight the device and press OK, then highlight Change name and press OK again. Press OK again to use the virtual keyboard to change the name of the device.

Channel List

The TV sorts all stored channels in the Channel List. Press the OK button to open the Channel List in Live TV mode. You can press the Red button to scroll up
the list page by page, or press the Green button to scroll down.
If desired. you can filter or sort the channels or find a channel in the channel list. Press the Yellow button to display the Select More options. Available options are Select Type, Sort and Find. Sort option may not be available depending on the selected country during the initial setup process.
To filter the channel highlight Select Type and press the OK button. You can select among Categories, Digital, Radio, Free, Encrypted, Analogue, Favourite and Network options to filter the channel list or select Broadcast option to see all installed channels in the channel list. Available options may differ depending on the operator selection.
To sort the channels highlight Sort and press the OK button. Select one of the available options and press OK again. The channels will be sorted according to your selection.
To find a channel highlight Find and press the OK button. Virtual keyboard will be displayed. Enter all or a portion of the name or number of the channel you went to find highlight the check mark symbol on the keyboard and press OK. Matching results will be listed.
Note: If any option except Broadcast is selected in the Select Type menu, you can only scroll through the channels that are currently listed in the channel list using the are currently listed in the channel list using the Prgramme +/- buttons on the remote.

Editing the Channels and the Channel List
You can edit the channels and the channel list using the Channel Skip, Channel Swap, Channel Moveand Channel Edit options under the Settings> Channel> Channels menu. You can access the Settings menu from the Home Screen or from the TV options menu in Live TV mode.

Note: The options Channel Swap, Channel Move and Channel Edit may not be available and appear as grayed out depending on the operator selection and operator related settings. LCN setting in the menu, as it prevents channel editing. This option might be set to On by default depending on the selected country during the initial setup process.

Managing Favorite Channel Lists
You can create four different lists of your favorite channels. These lists include only the channels that OK button to display the channel list. Then press Blue button to access favorite lists. If one of the lists is being displayed on the screen you can press the Left or Right directional button to switch from one list to another. In order to change the position of a channel highlight that channel and press the Yellow button. Then use the Up and Down directional buttons to move the channel to the desired position and press OK. Highlight a channel in the list and press the OK button to watch.
To add the currently watched channel to one of your favorite lists select the desired favorite list as described above and press the Menu button on the remote. Then enter the Channels menu, highlight Add to My Favorites option and press OK. The channel will be added to the selected favorite list.
Only the currently watched channel can be added to a favorite list. To remove a channel from a favorite list open the favorite list, highlight that channel and press the Blue button. If you want to set one of your Favorite channel lists as the main channel list, you need to select the desired favorite list as described above. Then set the Select Type option to Favorite. Open the channel list and press the Yellow button to see the options. Depending on the operator selection this feature may be blocked and not work properly. Programme Guide By means of Electronic Programme Guide (EPG) function of your TV you can browse the event schedule of the currently installed channels on your channel list. It depends on the related broadcast whether this feature is supported or not.
In order to access the Electronic Programme Guide on the Home Screen press the Guide button on the remote. Electronic Programme Guide is also available
in Live TV mode. To switch to Live TV mode you can either press the Exit button or highlight the Live TV app from the Apps row on the Home Screen and press OK. For some countries, the Live TV app will be situated in the Home tab on the Home Screen and the row with this app will be named as Favorite Apps. To access the programme guide while in Live TV mode, press the Guide button on your remote.
Use the directional buttons to navigate through the programme guide. You can use the Up/Down directional buttons or Programme +/- buttons to switch to previous/next channel on the list and Right/ Left directional buttons to select a desired event of the currently highlighted channel. If available, the full name, start-end time and date, genre of the highlighted event and a brief information about it will be displayed on the screen.
Press Blue the desired type quicker. Press Yellow button to see detailed information on the highlighted event. You can also use Red and Green buttons to see events of previous day and next day. The functions will be assigned to the coloured buttons on the remote when they are available. Follow the on- screen information for accurate button functions.
Press Record button to add a timer for the highlighted by setting the Schedule type option as Reminder or
Record. When other parameters are set highlight Add and press OK. The timer will be added to the schedule list. You can access the schedule list from the Record menu in Live TV mode.
The guide can not be displayed if TV input source is blocked from the Settings>Channel>Parental Controls>Inputs Blocked menu in Live TV mode or on Home Screen.

Connecting to the Internet

You can access the Internet via your TV, by connecting the network settings in order to enjoy a variety of streaming content and internet applications. These Settings>Network & Internet menu. You can also highlight the Connected/ Not Connected icon on the Home screen and press OK to access this menu. For further information refer to Network & Internet section under the title of Settings.

Wired Connection
Connect your TV to your modem/router via an Ethernet cable. There is a LAN port on the rear side of your TV. The status of the connection under the Ethernet section in the Network & Internet menu will change from Not connected to Connected.

DAEWOO 32DM54HA Colour Television with Remote Control - Connecting to the
Internet 1

Broadband ISP connection
LAN (Ethernet) cable
LAN input on the rear side of the TV

You might be able to connect your TV to a network In that case, you can connect your TV directly to the network using an Ethernet cable.

Network wall socket
LAN input on the rear side of the TV

Wireless Connection
A wireless LAN modem/router is required to connect the TV to the Internet via wireless LAN.
Highlight Wi-Fi option in the Network & Internet menu and press OK to enable wireless connection. Available networks will be listed. Select one and press OK to connect. For more information refer to Network & Internet section under the title of Settings.

1. Broadband ISP connection

A network with hidden SSID can not be detected by other devices. If you want to connect to a network with hidden SSID, highlight the Add new network option under the Settings>Network & Internet menu on the Home Screen and press OK. Add the network by entering its name manually using the related option.
Some networks may have an authorisation system that requires a second login as such in a work environment.
In this case, after connecting to the wireless network you want to connect to, highlight situated on the upper right of the Home Screen and press OK.
Then highlight the Sign in to Wi-Fi network and press OK. Enter your credentials to log in.
A Wireless-N router (IEEE 802.11a/b/g/n/ac) with simultaneous 2.4 and 5 GHz bands is designed to increase bandwidth. These are optimized for smoother wireless gaming.
Use a LAN connection for quicker data transfer between other devices like computers. distance and number of obstructions between the transmission products, the configuration of these and the products that you use. The transmission may on the radio wave conditions, DECT phones or any other WLAN 11b appliances. The standard values of the transmission speed are the theoretical maximum values for the wireless standards. They are not the actual speeds of data transmission.
The Wireless feature of the TV supports 802.11 a,b,g,n & ac type modems. It is highly recommended that you should use the IEEE 802.11n communication protocol in order to avoid any possible problems while watching videos.
You must change your modem’s SSID when there are any other modems around with the same SSID. You can encounter connection problems otherwise. Use a
wired connection if you experience problems with a wireless connection.
A stable connection speed is required to play back streaming content. Use an Ethernet connection if the wireless LAN speed is unstable.

Multi Media Player

On the Home Screen scroll to Apps row, select Multi Media Player (MMP) and press the OK button to launch. For some countries, the Multi Media Player app will be situated in the Home tab on the Home Screen and the row with this app will be named as
Favourite Apps.
Select the media type on the main media player screen. On the next screen, you can press the Menu button to access a list of menu options while the focus is on a the thumbnail size and turn your TV into a digital photo frame. You will also be able to copy, paste and delete a FAT32 formatted USB storage device is connected to the TV. Additionally you can switch the viewing style by selecting either Normal Parser or Recursive Parser. In Normal Parser folders if any available. So only the selected type of selected type, the folder will be assumed as empty. In Recursive Parser mode the source will be searched Back/Return button to close this menu.
In order to activate photo frame feature select Photo as the media type. Then press the Menu button, highlight Photo Frame and press OK. If you select One Photo mode option and press OK the image that you set as photo frame image earlier will be displayed when photo frame feature is activated. If you select the USB storage deviceRecursive Parser mode) will be displayed. To set the photo frame image press the Menu your choice is displayed, highlight Photo Frame Image and press OK.
highlighted video will be displayed in a small window on the left side of the screen if the view style is set to List View. Press the Blue button to switch between the List View and Grid View. You can also use Programme +/-

Video Files
Press OK Info: Display the info bar. Press twice to display the Play/pause: Pause and resume the playback.
Rewind: Start reverse playback. Press consecutively to set the rewind speed.
Fast Forward: Start fast forward playback. Press consecutively to set the forward playback speed.
Stop: Stop the playback and return to the media player screen.
Programme +: Switch to next file.
Programme -: Switch to previous file.
Back/Return: Return to the media player screen.

Music Files
Press OK Info: Play/pause: Pause and resume the playback.
Rewind: Press and hold to rewind. Fast Forward: Press and hold to fast forward.
Stop: Stop the playback.
Programme +: Switch to next file.
Programme -: Switch to previous file.
Back/Return: Return to the media player screen.
If you press Back/Return button without stopping the

browsing in the multimedia player. You can use the
media player buttons to control the playback. Theplayback will stop if you exit the media player or switch
the media type to Video.
If you press Back/Return button without stopping the browsing in the multimedia player. You can use the media player buttons to control the playback. The
playback will stop if you exit the media player or switch the media type to Video.

Photo Files
Press OK When you press the Play button slide show will start and device, depends on the viewing style, will be displayed in order. If the Repeat option is set to None only the between the highlighted one and the last listed one will be displayed. The slide show will stop after
Info: Display the info bar. Press twice to display the extended information.
Play/pause: Pause and resume the slide show.
Green button (Rotate/Duration): Rotate the image / Set the interval between the slides. Zoom in on the image
Programme +: Switch to next file.
Programme -: Switch to previous file.
Back/Return: Return to the media player screen.

Text Files
When you press the OK button slide show will start and device, depends on the viewing style, will be displayed in order. If the Repeat option is set to None only the between the highlighted one and the last listed one will be displayed. The slide show will stop after
Info: Display the info bar. Press twice to display the extended information.
Play/pause: Pause and resume the slide show.
Programme +: Switch to next file.
Programme -: Switch to previous file.
Directional buttons (Down or Right / Up or Left): Switch to next page. / Switch to previous page.
Back/Return: Stop the slide show and return to the media player screen.

Menu Options
Press the Menu button to see available options while
Pause/Play: Pause and resume the playback or the slide show.
Repeat: Set the repeat option. Highlight an option and press OK to change the setting. If Repeat One option is back or displayed. If the Repeat All option is selected in the storage device, depends on the viewing style, will be repeatedly played back or displayed. OK to change the setting.
Duration: Set the interval between the slides. Highlight an option and press OK to change the setting. You can also press the Green button to set. This option will not be available if the slide show is paused. Rotate: Rotate the image. The image will be rotated 90 degrees clockwise each time you press OK. You can also press the Green button to rotate. This option will not be available if the slide show is not paused.
Effect: Apply various effects to the slide show. Highlight an option and press OK to change the setting. You can also press the Yellow button to set. This option
will not be available if the slide show is paused.
Zoom: Zoom in on the image that is currently being displayed. Highlight an option and press OK to change
the setting. You can also press the Yellow button to zoom in. This option will not be available if the slide show is not paused.
Font: Set the font options. Size, style and colour can be set according to your preferences.
Show Info: Display the extended information.
Photo Frame Image: Set the currently displayed image as photo frame image. This image will be displayed if the One Photo mode is selected instead of the connected storage device while activating the back as a slideshow when photo frame feature is activated.
Hide/Show Spectrum: Hide or show the spectrum if available.
Lyric Options: Display lyric options if available.
Open the power menu of your TV. You can use the option here to turn the screen ress a button on the remote or on the TV to turn the screen on again.
Picture Settings: Display the picture settings menu.
Sound Settings: Display the sound settings menu.
Audio Settings: Set the soundtrack option if more then one available.
Last Memory: Set to Time if you want to resume the playback from the position where it was stopped next the playback will start from the beginning. Highlight an option and press OK to change the setting.
Seek: the numeric and directional buttons to enter the time and press OK.
Subtitle: Set your subtitle preference if any available. Set to Subtitle Encoding: Display subtitle encoding options if available.

From USB Connection
IMPORTANT! before connecting them to the TV. Manufacturer will not be of USB devices (e.g. MP3 Players) or USB hard disk drives/ memory sticks may not be compatible with this TV. The TV supports FAT32 disk formatting. FAT32 formatted devices with a storage capacity larger than 192TB are not supported.
You can view your photos, text documents or play your storage device on the TV. Plug in the USB storage device to one of the USB inputs on the TV. On the main media player screen select the desired OK button. Follow the on-screen instructions for more information on other available button functions.
Note: Wait a little while before each plugging and unplugging cause physical damage to the USB player and the USB device

From a Mobile Device via DMR
Make sure that your mobile device is connected to the same network as your TV. On the TV, scroll to Apps row on the Home Screen, select Multi Media Player (MMP) and press the OK button to launch. For some countries, the Multi Media Player app will be situated in the Home tab on the Home Screen and the row with this app will be named as Favourite Apps. Select the media type on the main media player screen. On the next screen, press the Blue button to switch the List View layout. Then press the Back button. DMR (Digital Media Renderer) option will appear among the media type options. Highlight the DMR option and press the OK button. The TV is ready to receive the sharing icon or on the related option from the options menu of your mobile device. Available devices will be
listed. Select your TV from the list. You can get the device name of your TV from the Settings>Device Preferences>About menu on the Home screen. If desired, the name of the TV can also be changed entering a custom name using the options of the Device name menu. If the connection is successfully displayed on your TV.

USB Recording

To record a programme, you should first connect aUSB storage device to your TV while the TV is switched off. You should then switch on the TV to enable the
recording feature.
To record long duration programmes such as movies, it is recommended to use USB Hard disk drives (HDD’s). Recorded programmes are saved onto the connected USB storage device. If desired, you can store/copy recordings onto a computer; however, these files will not be available to be played on a computer. You can play the recordings only via your TV.
Lip Sync delay may occur during the time shifting. Radio record is supported.
If the writing speed of the connected USB storage device is not sufficient, the recording may fail and the time shifting feature may not be available.
It is recommended to use USB hard disk drives for recording HD programmes.
Do not pull out the USB/HDD during a recording. This may harm the connected USB/HDD.
Some stream packets may not be recorded because of signal problems, as a result sometimes videos may freeze during playback.
If a recording starts from timer when teletext is on, a dialogue will be displayed. If you highlight Yes and press OK teletext will be turned off and recording will start.

Instant Recording
Press Record button to start recording an event instantly while watching a programme. Press Stop button to stop and save the instant recording.
You can not switch broadcasts during the recording mode.

Watching Recorded Programmes
Select Record List from the Record menu in Live TV mode and press OK. Select a recorded item from the list (if previously recorded). Press the OK button
to watch.
Press the Stop or Back/Return button to stop a playback.
The recordings will be named in the following format: Channel NameDate(Year/Month/Day) Duration(Hour/Minute/Second)_Programme Name.

Timeshift Recording
In order to use timeshift recording feature Time Shift Mode option in the Record>Time Shift Mode menu should be enabled first.
In timeshifting mode, the programme is paused and simultaneously recorded to the connected USB storage device. Press Pause/Play button while watching a broadcast to activate timeshifting mode. Press Pause/ Play button again to resume the paused programme from where you stopped. Press the Stop button to stop timeshift recording and return to the live broadcast. Disk Setup wizard will be displayed when the Pause/Play button is pressed. You can either choose Auto or Manual setup mode. In Manual mode, if you prefer, you can format your USB storage device and specify the storage space that will be used for timeshift function. When the setup is complete, the Disk Setup Result will be displayed. Press Exit button.
Timeshift function will not be available for radio broadcasts.

Disk Format
When using a new USB storage device, it is recommended that you first format it using the Format option in the Record>Device Info menu in Live TV mode. Highlight the connected device on the Device Info screen and press OK or Right directional button to see the list of available options. Then highlight Format and press OK to proceed. A confirmation dialogue will be displayed. Highlight Yes and press OK to start formatting.
IMPORTANT: Formatting your USB storage device will erase ALL the data on it and its file system will be converted to FAT32. In most cases operation errors will be fixed after a format but you will lose ALL your data.

Schedule List
You can add reminders or record timers using the Schedule List menu. You can access the Schedule List from the Record menu in Live TV mode. Highlight Schedule List and press OK. Previously set timers will be listed if any available.
Press Record button to add a timer while the Schedule List menu is displayed on the screen. You can define the type of the timer by setting the Schedule Type option as Reminder or Record. When other parameters are set highlight Add and press OK. The timer will be added to the list.
If any available, you can also edit or delete the timers on this list. Highlight the timer of your choice and press OK. Edit and Delete options will appear at the bottom of the screen. Highlight the desired option and press OK. After you edited a timer you can choose either to replace it or add it as a new timer. If you choose the Replace option, the timer will be saved with the new settings. If you choose the Add option, the timer will be added to the list as a new timer. Highlight Replace or Add according to your preference and press OK to proceed. When you choose to delete a timer a confirmation dialogue will be displayed on the screen. Highlight Yes and press OK to delete the selected timer.
A warning message will be displayed if the time intervals of two timers overlap. You can not set more than one timer for the same time interval.
Press EXIT button to close the Schedule List.

CEC
With CEC function of your TV you can operate a connected device with the TV remote control. This function uses HDMI CEC (Consumer Electronics Control) to communicate with the connected devices. Devices must support HDMI CEC and must be connected with an HDMI connection.
In order to make use of the CEC functionality the related option in the menu should be switched on.
To check, switch on or off the CEC function, do the following:

Enter the Settings>Device Preferences>Inputs menu on the Home Screen or TV options>Set-tings>Device Preferences>Inputs menu in Live TV mode.
Scroll down to Consumer Electronic Control (CEC) section. Check if the HDMI control option is switched on.
Highlight the HDMI control option and press OK to switch on or off.

Make sure that all CEC settings are properly set up on the connected CEC device. The CEC functionality has different names on different brands. CEC function
might not work with all devices. If you connect a device with HDMI CEC support to your TV, the related HDMI input source will be renamed with the connected device’s name.
To operate the connected CEC device, select the related HDMI input source from the Inputs menu on the Home Screen. Or press the Source button ifthe TV is in Live TV mode and select the related HDMI input source from the list. To terminate this operation and control the TV via the remote again, press the Source button, which will still be functional, on the remote and switch to another source.
The TV remote is automatically able to control the device once the connected HDMI source has been selected. However not all buttons will be forwarded to the device. Only devices that support CEC Remote Control function will respond to the TV remote control. The TV supports also ARC(Audio Return Channel) feature. This feature is an audio link meant to replace other cables between the TV and the audio system (AN receiver or speaker system). Connect the audio system to the HDMI2 input on the TV to enable ARC feature.
In order to activate ARC feature the Speakers option should be set as External Audio System. You can access this option from the TV options or TV options>-
Settings> Device Preferences>Sound menu in Live TV mode or from Settings>Device Preferences>Sound menu on the Home Screen. When ARC is active, TV will mute its other audio outputs automatically. So you will hear audio from connected audio device only. The volume control buttons of the remote will be directed to connected audio device and you will be able to control the volume of the connected device with your TV remote.
Note: ARC is supported only via the HDMI2 input.

Google Cast

With the built-in Google Cast technology you can cast the content from your mobile device straight to your TV. If your mobile device has Google Cast feature, you can mirror your device’s screen to your TV wirelessly. Select Cast screen option on your android device. Available devices will be detected and listed. Select your TV from the list and tap on it to start casting. You can get the network name of your TV from the Settings>Device Preferences>About menu on the Home screen. Device name will be one of the shown articles. You can also change the name of your TV. Highlight Device name and press OK. Then highlight Change and press OK again. You can either select one of the predefined names or enter acustom name. To cast your device’s screen to the TV screen…

On your android device, go to ‘Settings’ from the notification panel or home screen
Tap on ‘Device Connectivity’
Tapon the ‘Easy projection’ and enable ‘Wireless projection’. Available devices will be listed
Select the TV you would like to cast to

Slide down the notification panel
Tap on ‘Wireless projection’
Select the TV you would like to cast to If the mobile app is Cast-enabled, such as YouTube, Dailymotion, Netflix, you can cast your app to your TV. On the mobile app, look for the Google Cast icon and tap on it. Available devices will be detected and listed. Select your TV from the list and tap onit to start casting.

To cast an app to the TV screen…

On your smartphone or tablet, open an app that supports Google Cast
Tap the Google Cast icon
Select the TV you would like to cast to
The app you selected should start playing on TV

Notes:
Google Cast works on Android and iOS. Make sure that your mobile device is connected to the same network as your TV. The menu options and namings for Google Cast function on your Android device can differ from brand to brand and can change with time. Refer to your device’s manual for latest information on Google Cast function.

HBBTV System

HbbTV (Hybrid Broadcast Broadband TV) is a standard that seamlessly combines TV services delivered via broadcast with services delivered via broadband and also enables access to Internet only services for consumers using connected TVs and set-top boxes. Services delivered through HbbTV include traditional broadcast TV channels, catch-up services, video-on-demand, electronic programme guide, in- teractive advertising, personalisation, voting, games, social networking and other multimedia applications. HbbTV applications are available on channels where they are signalled by the broadcaster.
The HbbTV applications are generally launched with the press of a coloured button on the remote. Generally a small red button icon will appear on the screen in
order to notify the user that there is an HbbTV application on that channel. Press the button indicated on the screen to launch the application.
HbbTV applications use the buttons on the remote control to interact with the user. When an HbbTV application is launched, the control of some buttons are owned by the application. For example, numeric channel selection may not work on a teletext application where the numbers indicate teletext pages. HbbTV requires AV streaming capability for the platform. There are numerous applications providing VOD (video on demand) and catch-up TV services. The OK (play&pause), Stop, Fast forward, and Rewind buttons on the remote control can be used to interact with the AV content.
Note: You can enable or disable this feature from the TV Options>Advanced Options>HBBTV Settings menu in Live TV mode.

Quick Standby Search

If earlier an automatic search is performed, your TV will search for new or missing digital channels at 05:00 am every morning while in quick standby mode.
And if the Auto Channel Update option in the Set- tings> Channel menu is enabled the TV will wake up within 5 minutes after it is switched into quick standby
mode and search for channels. Standby LED will blink during this process. Once the standby LED stops blinking the search process is completed. Any new found channels will be added to the channel list. If the channel list is updated, you will be informed on the changes at the next power on.

Software Update

Your TV is capable of finding and updating the firmware automatically via Intemet.
To experience the best use of your TV and benefit from the latest improvements make sure your system is always up to date.

Software update via internet
On the Home Screen enter the Settings>Device Preferences>About menu in order to update your Android system version. Move the focus to the System update option and press OK. You will be informed about the system status and the time at which the device was last checked for an update will be displayed. The Check for update option will be highlighted, press OK if you want to check for an available update.
Note: Do not unplug the power cord during the reboot process. If the TV fails to come on after the upgrade, unplug, wait for two minutes then plug it back in.

Troubleshooting & Tips

TV does not switch on

Make sure the power cord is plugged in securely to power outlet.
Disconnect the power cable from the power outlet. Wait for one minute then reconnect it.
Press the Standby/On button on the TV.

TV does not respond to the remote control

The TV requires some time to start up. During this time, the TV does not respond to the remote control or TV controls. This is normal behaviour.
Check if the remote control is working by means of a mobile phone camera. Put the phone in camera mode and point the remote control to the camera lens. If you press any key on the remote control and you notice the infra red LED flicker through the camera, the remote control is working. The TV needs to be checked.
If you do not notice the flickering, the batteries may be exhausted. Replace the batteries. If the remote is still not working, the remote control might be broken and needs to be checked.
This method of checking the remote control is not possible with remote controls which are wirelessly paired with the TV.

No Channels

Make sure that all cables are properly connected and that the correct network is selected.
Make sure that the correct channel list is selected.
Make sure that you have entered the correct channel frequency if you have done manual tuning.

No picture / distorted picture

Make sure that the antenna is properly connected to the TV.
Make sure that the antenna cable is not damaged.
Make sure that the correct device is selected as the input source.
Make sure that the external device or source is properly connected.
Make sure that the picture settings are set correctly.
Loud speakers, unearthed audio devices, neon lights, high buildings and other large objects can influence reception quality. If possible, try to improve the reception quality by changing the antenna direction or moving devices away from the TV.
Change to a different picture format, if the picture does not fit the screen
Make sure that your PC uses the supported resolution and refresh rate.

No sound / poor sound

Make sure that the sound settings are correctly set.
Make sure that all cables are properly connected.
Make sure that the volume is not muted or set to zero, increase the volume to check.
Make sure that the TV audio output is connected to the audio input on the external sound system.
Sound may be coming from only one speaker. Check the balance settings from Sound menu.

Input sources – can not be selected

Make sure that the device is connected to the TV.
Make sure that all cables are properly connected.
Make sure that you select the right input source which is dedicated to the connected device.
Make sure that the right input source is not hidden from the Inputs menu.

VGA Input Typical Display Modes

The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions.

Index	Resolution	Frequency
1	640×480	60Hz
2	640×480	72Hz
3	640×480	75Hz
4	800×600	56Hz
5	800×600	60Hz
6	800×600	72Hz
7	800×600	75Hz
8	1024×768	60Hz
9	1024×768	70Hz
10	1024×768	75Hz
11	1152×864	75Hz
12	1280×768	60Hz
13	1280×768	75Hz
14	1280×960	60Hz
15	1280×960	75Hz
16	1280×1024	60Hz
17	1280×1024	75Hz
18	1360×768	60Hz
19	1366×768	60Hz
20	1400×1050	59Hz
21	1400×1050	60Hz
22	1400×1050	75Hz
23	1440×900	60Hz
24	1440×900	75Hz
25	1600×1200	60Hz
26	1680×1050	59Hz
27	1680×1050	60Hz

AV and HDMI Signal Compatibility

Source	Supported Signals
Composite I Back AV	PAL

SECAM
NTSC4.43
NTSC3.58
Component / YPbPr| 4801. 480p| 60Hz
5761. 576p| 50Hz
720p| 50Hz.60Hz
1080i| 50Hz.60Hz
HDMI| 4801| 60Hz
480p| 60Hz
5761. 576p| 50Hz
720p| 50Hz.60Hz
10801| 50Hz.60Hz
1080p| 24Hz. 25Hz. 30Hz. 50Hz. 60Hz

In some cases a signal on the TV may not be displayed properly. The problem may be an inconsistency with standards from the source equipment (DVD, Set-top
box, etc. ). If you do experience such a problem please contact your dealer and also the manufacturer of the source equipment.

Supported File Formats for USB Mode

Video

Video Codec	Resolution	Bit Rate	Profile	Container
VP9	1920×1080@60fps	40Mbps	Profile0.2	MKV (.mkv) WebM (.webm)
HEVC/H.265	1920×1080©60fps	50Mbps	Main(MainlO
Profile. High Tier @Level 4.1	MP4 (mp4..mov). 3GPP (.3gpp, .3gp),

stream (.ts..trp, .tp). MPEG transport MKV (.mkv), WebM (.webm), FLV (.fN).
AVI (.avi). 11265 (.265)
MPEG1I2| 1920×10806.60fps| 80Mbps| MP@HL| MPEG program stream (.DAT, .VOB,
.MPG, .MPEG), MPEG transport stream
(.ts, .trp, .tp), MP4 (.mp4, .mov), 3GPP
(.3gpp, .3gp), AVI (.avi), MKV (.mkv),
WebM (.webm), ASF (.asf), WMV
(.wmv), OGM (.ogm)
MPEG4| 1920×10804/60fps| 40Mbps| •Simple Profile
•Advanced Simple
Profile@Level 5
•GMC is not
supported| MP4 (.mp4..mov). 3GPP (.3gpp, .3gp)• AVI (.avi). MKV (.mkv). WebM (.webm). ASF WMV (.wmv).FLV (.fN). OGM (.asf).
(.ogm), MPEG transport stream (is. .trp. .tp).MPEG program stream (.DAT..V0B. .MPG..MPEG)
Sorenson 11.263| 1920×1080@e0fps| 40Mbps| | FLV (.flv)
AVI (.avi)
11.| 1920×1080@e0fps| 40Mbps| | FLV (.fly), MP4 (.mp4, .mov). 3GPP (.3gpp..3gp).AVI (.avi).ASF (as1). WMV (.wmv)
11.| 1920X1080©30fps| 62.5Mbps| main and high profile up to level 4.1| FLV (.fly)• MP4 (.mp4, .mov). 3GPP (.3gpp..3gp), MPEG transport stream (.ts, Irp..tp).ASF (.asf), WMV (.wmv), AVI (.avi). MKV (.mkv). WebM (.webm), OGM (.ogm). MPEG program stream (.DAT..V0B..MPG..MPEG).11264 (.264)
AVS| 1920×1080@60fps| 40Mbps| Jizhun profile © Level 6.0| MPEG transport stream (.ts..trp..tp). AVS (.ays)
AVS+| 1920×1080@e0fps| 50Mbps| Broadcasting profile©Level 6.0.1.08.60| MPEG transport stream (.ts..trp, .tp). AVS (.ays)
WMV3| 1920×1080@60fps| 40Mbps| | ASF (.asf), AVI (.avi), MKV (.mkv), WebM (.webm), WMV (.wmv), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov), OGM (.ogm)
VC1| 1920×1080@60fps| 40Mbps| @Level 3| MPEG transport stream (.ts, .trp, .tp), ASF (.asf), WMV (.wmv), AVI (.avi), MKV (.mkv), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov), VC1 (.vc1)
Motion JPEG| 640×480@30fps| 10Mbps| | AVI (.avi), 3GPP (.3gpp, .3gp), MP4
(.mp4, .mov), MKV (.mkv), WebM
VP8| 1920×1080@60fps| 20Mbps| | 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov), AVI (.avi), OGM (.ogm)
RV30/RV40| 1920×1080@60fps| 40Mbps| | RM (.rm, .rmvb), MKV (.mkv), WebM (.webm)

Audio

Audio Codec| Sample rate| Channel| Bit Rate| Container| Note
---|---|---|---|---|---
MPEG1/2
Layer1| 16KHz ~ 48KHz| Up to 2| 32Kbps~ 448Kbps| MP3 (.mp3), AVI (.avi), ASF (.asf), WMV (.wmv), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp),MP4 (.mp4, .mov, m4a),
MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, WAV (.wav), OGM (.ogm)|
MPEG1/2
Layer2| 16KHz ~ 48KHz| Up to 2| 8Kbps ~
384Kbps| MP3 (.mp3), AVI (.avi), ASF (.asf), WMV (.wmv), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, (.wav), OGM (.ogm)|
MPEG1/2/2.5
Layer3| 8KHz ~ 48KHz| Up to 2| 8Kbps ~
320Kbps| MP3 (.mp3), AVI (.avi), ASF (.asf), WMV (.wmv), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB,
(.wav), OGM (.ogm)|
AC3(DD)| 32KHz, 44.1KHz,
48KHz| Up to 5.1| 32Kbps ~
640Kbps| AC3 (.ac3), AVI (.avi), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), WMV (.wmv), ASF (.asf), OGM (.ogm)|
EAC3(DDP)| 32KHz, 44.1KHz,
48KHz| Up to 5.1| 32Kbps ~
6Mbps| EAC3 (.ec3), AVI (.avi), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), WMV (.wmv), ASF (.asf), OGM (.ogm)|
AAC-LC, HEAAC| 8KHz ~ 48KHz| Up to 5.1| AAC-LC: 12kbps~ 576kbps
V1 6kbps ~ 288kbps V2: 3kbps ~ 144kbps| AAC (.aac), AVI (.avi), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), FLV (.wav), WMV (.wmv), ASF (.asf), OGM (.ogm)|
WMA| 8KHz ~ 48KHz| Up to 2| 128bps ~
320Kbps| ASF (.asf), WMV (.wma, .wmv), AVI (.avi), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov)| WMA 7,
WMA 8,
WMA 9
Standard
WMA 10 Pro M0| 8KHz ~ 48KHz| Up to 2| < 192kbps| ASF (.asf), WMV (.wma, .wmv), AVI (.avi), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov)|
WMA 10 Pro M1| 8KHz ~ 48KHz| Up to 5.1| < 384kbps| ASF (.asf), WMV (.wma, .wmv), AVI (.avi), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov)|
WMA 10 Pro M2| 8KHz ~ 96KHz| Up to 5.1| < 768kbps| ASF (.asf), WMV (.wma, .wmv), AVI (.avi), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov)|
VORBIS| Up to 48KHz| Up to 2| | MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), Ogg (.ogg), WMV (.wmv), ASF (.asf), AVI (.avi)| Supports stereo
decoding only
DTS| Up to 48KHz| Up to 5.1| < 1.5Mbps
(Pure DTS core)| MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), WAV (.wav), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), AVI (.avi), OGM (.ogm), DTS (.dts)|
DTS LBR| 12KHz, 22KHz, 24KHz, 44.1KHz, 48KHz| Up to 5.1| Up to 2Mbps| MP4 (.mp4, .mov), 3GPP (.3gpp, .3gp), MPEG transport stream (.ts, .trp, .tp)|
DTS XLL| Up to 96KHz| Up to 6| | MPEG transport stream (.ts, .trp, .tp, .mts, .m2ts), MP4 (.mp4, .mov), 3GPP (.3gpp, .3gp)|
LPCM| 8KHz ~ 48KHz| Mono, Stereo,
5.1| 64Kbps ~ 1.5Mbps| WAV (.wav), AVI (.avi), MKV (.mkv, .mka), WebM (.webm), 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a), MPEG transport stream (.ts, .trp, .tp), MPEG program stream (.DAT, .VOB, .MPG, .MPEG), WMV (.ogm)|
IMA-ADPCM
MS-ADPCM| 8KHz ~ 48KHz| Up to 2| 2Kbps~
384Kbps| WAV (.wav), AVI (.avi), MKV (.mkv, .mka), WebM (.webm), OGM (.ogm)|
G711 A/mu-law| 8KHz| 1| 64Kbps| WAV (.wav), AVI (.avi), MKV (.mkv,|
LBR (cook)| 8KHz 11.025KHz, 22.05KHz, 44.1KHz| Up to 5.1| 6Kbps ~ 128Kbps| RM (.rm, .rmvb, .ra)|
FLAC| 8KHz~96KHz| Up to 7.1| < 1.6Mbps| MKV (.mkv, .mka), WebM (.webm),|
OPUS| 8KHz ~ 48KHz| Up to 6| 6Kbps ~ 510Kbps| MKV (.mkv, .mka) WebM (.webm)|
AMR-NB| 8KHz| 1| 4.75 ~ 12.2Kbps| 3GPP (.3gpp, .3gp) MP4 (.mp4, .mov, m4a)|
AMR-WB| 16KHz| 1| 6.6 ~ 23.85Kbps| 3GPP (.3gpp, .3gp), MP4 (.mp4, .mov, m4a)|

Picture

Image	Photo	Resolution (width x height)
JPEG	Base-line	15360×8640
Progressive	1024×768
PNG		9600×6400
BMP		9600×6400
GIF		6400×4800
WebP		3840×2160
HEIF		4000×3000

Subtitle
Internal

File Extension	Container	Subtitle Codec
ts, trp, tp	TS	DVB Subtitle Teletext CC(EIA608)

PGS
mp4| MP4| Vobsub PGS TX3G
mkv| MKV| ASS SSA SRT VobSub PGS

External

File Extension	Subtitle Parser	Remark
.srt	SubRip
.ssa/ .ass	SubStation Alpha
Advanced SubStation Alpha
.smi	SAMI
.sub	MicroDVD SubIdx (VobSub)
.txt	TMPlayer

Supported DVI Resolutions

When connecting devices to your TV’s connectors by using DVI converter cable(DVI to HDMI cable – not supplied), you can refer to the following resolution information.

| 56Hz| 60Hz| 66Hz| 70Hz| 72Hz| 75Hz
---|---|---|---|---|---|---
640×480| | x| | | | x
800×600| x| x| | | | x
1024×768| | x| | x| | x
1280×768| | x| | | | x
1280×960| | x| | | |
1360×768| | x| | | |
1366×768| | x| | | |
1280×1024| | x| | x| | x
1400×1050| | x| | | |
1600×900| | x| | | |

Specification

TV Broadcasting	PAL BG/I/OK SECAM BG/DK
Receiving Channels	VHF (BAND I/III) – UHF (BAND U) – HYPERBAND
Digital Reception	Fully integrated digital terrestrial-cable-satellite

TV(DVB-T-C-S) (DVB-T2. DVB-S2 compliant)
Number of Preset Channels| 12200
Channel Indicator| On Screen Display
RF Aerial Input| 75 Ohm (unbalanced)
Operating Voltage| 220-240V AC. 50Hz
Audio| German+Nicam Stereo
Audio Output Power (WRMS.) (10% THD)| 2 x 6
Power Consumption (W)| 65W
Networked Standby Power Consumption (W)| < 2
TV Dimensions DxLxH (with foot) (mm)| 176 x 732 x 481
TV Dimensions DxLxH (without foot) (mm)| 51/78 x 732 x 435
Display| 32″
Operation temperature and operation humidity| 0°C up to 40°C. 85% humidity max

Wireless LAN Transmitter Specifications

Frequency Ranges	Max Output Power
2400 – 2483,5 MHz (CH1-CH13)	< 100 mW
5150 – 5250 MHz (CH36 – CH48)	< 200 mW
5250 – 5350 MHz (CH52 – CH64)	< 200 mW
5470 – 5725 MHz (CH100 – CH140)	< 200 mW

Country Restrictions
This device is intended for home and office use in all EU countries (and other countries following the relevant EU directive) without any limitation except for the countries mentioned below.

Country	Restriction
Bulgaria	General authorization required for outdoor use and public service
Italy	If used outside of own premises, general authorization is required
Greece	In-door use only for 5470 MHz to 5725 MHz band
Luxembourg	General authorization required for network and service supply(not

for spectrum)
Norway| Radio transmission is prohibited for the geographical area within a radius of 20 km from the centre of Ny-Alesund
Russian Federation| In-door use only
Israel| 5 G Hz band only for 5180 MHz-5320 MHz range

The requirements for any country may change at any time. It’s recommended that user checks with local authorities for the current status of their national regulations for 5 GHz wireless LAN’s.

Licences

The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Manufactured under licence from Dolby Laboratories.
Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

Google, Android, Android TV, Chromecast, Google Play and YouTube are trademarks of Google LLC. This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate licence(s) from
Microsoft.
Content owners use Microsoft PlayReady™ content access technology to protect their intellectual property, including copyrighted content. This device uses PlayReady technology to access PlayReady-protected content and/or WMDRN- protected content. If the device fails to properly enforce restrictions on content usage, content owners may require Microsoft to revoke the device’s ability to consume PlayReady-protected content. Revocation should not affect unprotected content or content protected by other content access technologies. Content owners may require you to upgrade PlayReady to access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade.
The “Cl Plus” Logo is a trademark of Cl Plus LLP. This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a licence from Microsoft or an authorised Microsoft subsidiary.

Disposal Information

[European Union]
These symbols indicate that the electrical and electronic equipment and the battery with this symbol should not be disposed of as general household waste at its end-of-life. Instead, the products should be handed over to the applicable collection points for the recycling of electrical and electronic equipment as well as batteries for proper treatment, recovery and recycling in accordance with your national legislation and the Directive 2012/19/EU and 2013/56/EU.
By disposing of these products correctly, you will help to conserve natural resources and will help to prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of these products.
For more information about collection points and recycling of these products, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
[Business users]
If you wish to dispose of this product, please contact your supplier and check the terms and conditions of the purchase contract.
[Other Countries outside the European Union]
These symbols are only valid in the European Union. Contact your local authority to learn about disposal and recycling.
The product and packaging should be taken to your local collection point for recycling.
Some collection points accept products free of charge.
Note: The sign Pb below the symbol for batteries indicates that this battery contains lead.

1. Products
2. Battery

Hereby, VESTEL Elektronik Sanayi ve Ticaret A.Ş.,declares that the radio equipment type TFT IDTV is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: doc.vosshub.com

Vestel Elektronik Sanayi ve Ticaret A.Ş. Organize
Sanayi Bölgesi 45030 Manisa – Türkiye

Documents / Resources

| DAEWOO 32DM54HA Colour Television with Remote Control [pdf] Instruction Manual
32DM54HA, 32DM54HA Colour Television with Remote Control, Colour Television with Remote Control, Television with Remote Control
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format) >>

Download This Manual (PDF format)

Download this manual >>