anntlent AN-CPAL50-01 Cell Phone Signal Booster User Manual
- June 10, 2024
- anntlent
Table of Contents
AN-CPAL50-01 Cell Phone Signal Booster
User Manual
Introduction
With the popularity of mobile communications, people want to make a call
anytime, anywhere, so the coverage requirement of communication network is
higher and higher, but the reality is not so, sometimes mobile phone signal is
not very good, you want to make a smooth call, even in some places cell phone
cannot dial out. in this cases, cell phone signal booster can solve this
problem in a certain extent.
Features
- AGC(Automatic Gain Control): When the downlink output signal is too strong or self- oscillated, the uplink and downlink can automatically reduce the gain and reduce the interference signal
- Self- Oscillation elimination: The system detects self- Oscillation, first reduces the link gain, then detects the loop, and finds that the self- oscillation is eliminated, the system returns to normal working state, otherwise, the power is turned off to prevent interference signal.
- Inactivity Mode: When no user calls, the device is in standby mode, the uplink power amplifier is switched off, and the static power is decreased by 30%, so as to achieve the purpose of energy saving.
SAFETY WARNINGS
WARNING:
This equipment should be installed and operated with minimum distance 20cm
(8 inches)between the radiator & your body.
FCC Cautions:
-
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
— Reorient or relocate the receiving antenna.
-
— Increase the separation between the equipment and receiver.
-
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
— Consult the dealer or an experienced radio/TV technician for help
-
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instruction for
satisfying RF exposure compliance. -
This transmitter must not be co-located or operating in conjunction with any other Antenna or transmitter.
SAFTY WARNING:
- End users must follow the specific operating instruction for satisfying RF exposure compliance.
- Do not remove the covers during working.
- Do not try to repair or replace any components inside of the equipment. Alteration or abuse of the equipment or other components will void this product’s warranty, and could be dangerous to the user.
PACKAGE CONTENTS
-
Packages include the following:
① 1 Pcs AN-CPAL 50-01 Booster with FME Male connectors.
② DC Car Charge.
③Screws Mounting Kits.
④User manual (this document). -
Booster interface description:
LED light: The corresponding LED on the right is used to indicate the following different working conditions of the booster.
LED Indicator | Booster working conditions |
---|---|
LED LIGHT | Continuous GREEN @normal; |
Twinkly GREEN @input signals may be not enough;
Continuous YELLOW @ stronger input signals, AGC is working;
Twinkly YELLOW@ self–oscillation happen ,AGC is working.
Continuous RED@ power supply is shut down;
Twinkly RED@ self–oscillation happen but power supply is NOT shut down.
②Power supply jack: The booster uses a power input range of DC 5-12V.
③INDOOR and OUTDOOR port: The two ports are used to connect outdoor and
indoor antennas.
- Antennas and Cables:
In order to use the Booster, you still need the corresponding indoor antenna 1pcs, outdoor antenna 1pcs, outdoor cable 1pcs and indoor cable 1pcs.
Antennas and cables kitting information are as follows
Name| Model| Gain/Loss|
---|---|---|---
Indoor Antenna| Patch Antenna| PIT -PA -800-2500| 3dbi @698 -7137 MHz
3dbi @824-894 MHz
3.5dbi @1850-1990 MHz
3.5dbi @1710-2155 MHz|
Indoor Panel Antenna| PTE-PN-800-2500| 7dbi @ 98-787 MHz
7dbi @824 -894 MHz
8.5dbi @1850-1990 MHz
8.5dbi @1710-2155 MHz|
Outdoor Antenna| Magnet Antenna| PTE-MA-800-2500| 3dbi @698-787 MHz
3dbi @824-894 MHz
3.5dbi @1850-1990 MHz
3.5dbi @1710 -2155 MHz|
Omni Tube Antenna| PTE-GF-700-2500| 3dbi @698-787MHz
3dbi @824-894MHz
5dbi @1710-1755 MHz
5dbi @1850-1990MHz
5dbi @2110 -2155MHz|
Indoor Cable| 20 feet 3D -FB
Coaxial cable with N male connector| PTE-3D-FB-5 NB| 2.19 db @698 -787MHz
2.29 db @824-894MHz
2.42 db @1710 -1755 MHz
2.55 db @1850-1990MHz
2.86 db @2110-2155MHz|
Outdoor Cable| 40feet 3D -FB
Coaxial cable with N male connector| PTE-3D-FB-10 NB| 5.21 db @698 -787 MHz
5.49 db @824-894 MHz
5.89 db @1710-1755 MHz
6.25 db @1850-1990 MHz
6.86 db @2110-2155 MHz|
Notes: The above model antennas are suitable for AN-L 50 VA-01 booster.
Warning: Unauthorized antennas,cables and/or coupling devices are
prohibited by FCC rules. Please contact FCC for details:1-888-CALL-FCC
The antenna, cables, and other accessories of the booster kits shall not be
modified without the approval of the ANNTLENT company, otherwise it shall be
deemed invalid.
INSTALLATION INSTRUCTIONS
-
Installation of Outdoor Antenna
The outside antenna comes with a strong magnet, simply put it on the roof of your vehicle. Run the cable of the outside antenna from the nearest door to the booster
and connect the connectors by hand, please do not use any tools, otherwise it will be over installed to break the connectors.
Note: Place the antenna at least 6 inches away from any windows including sunroofs, and 12 inches away from any antennas on the vehicle. -
Installation of Indoor Antenna
The inside patch antenna should be stuck on the back of the front seat and face the space you need to use your phone.
Note: Please don’t mount it on any metal surface. The vertical installation is better than the horizontal way. The inside antenna and outside antenna should be at least 6 ft (2m) apart, if possible.
Notes:
Booster transmitting in 1710-1755 MHz should be install/operate in one of two ways:
(i) the antenna for the device must be installed to comply with the 10 meter above ground maximum antenna height limitation OR
(ii) the antenna for the device has a 10 meter above ground maximum antenna height limitation when the device is used with a handset that covers the 1710-1755 MHz band and that owners could be subject to potential FCC enforcement action for noncompliance. -
Connect the Power Cord:
Connect the DC power cord into the vehicle’s DC power source, verify that all of the connections to the booster are tight and secure, plugging the power cord to the booster, the green LED light will glow, indicating that the booster is ready to use.
WARNING: The booster is rated for DC 5~12V input voltage. DO NOT use the booster with a high-voltage power supply. This could damage the booster or cause personal injury. -
Mounting the booster (optional):
Select a location to install the booster that is away from excessive heat, direct sunlight or moisture and that has proper ventilation. Recommended installation locations are: ![anntlent AN CPAL50 01 Cell Phone Signal Booster
- proper ventilation](https://manuals.plus/wp-content/uploads/2023/04 /anntlent-AN-CPAL50-01-Cell-Phone-Signal-Booster-proper-ventilation.png)
TROUBLESHOOTING AND SUPPORT
Problem | Resolution |
---|---|
LED is not light | 1. Find an alternate DC Car Charge and try again. |
2. Check the power outlet, the power adapter plug maybe is poor connected.
3. If the problem is still not solved, please contact our company support at
support@ANNTLENT.com
Booster has no effect| 1. Check whether the direction of the booster is wrong
connected.
2. Make a call to your mobile phone operator to determine if the frequency
band is correct.
3. Check whether the indoor and outdoor antenna is installed correctly
4. At the location where the outdoor is installed, if your mobile phone is
able to receive a stable 2 bars cell phone signal, If not, find a location
where the mobile phone can receive a better signal to install the outdoor
antenna.
Booster has effect ,but the effect is not ideal| Check if your outdoor signal
is very weak. If you can only receive one or two bars cell phone signal in the
outdoor.
If so, contact our customer service and ask to replace the booster or antenna
with a higher gain alternative.
Mobile phone can receive full signal, but can not normally make a call| It
Usually means that the booster is self-oscillated, please make the distance
between the indoor and outdoor antenna as far as possible, it is better to use
a wall or metal to Separate the indoor antenna and the out door antenna.
During using your Booster, if the Booster interferes with your radio or other
electronic device, move the Booster further away from those devices, you might
be able to solve it yourself.
If necessary, please contact your local dealer or send e-mail to our support
team by the following methods:
E-mail: support@ANNTLENT-tech.com
If you want to know about ANNTLENT Company and products for more information,
please visit at: www.ANNTLENT.com
Consumer booster warning label:
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider
and have your provider’s consent. Most wireless providers consent to the use
of signal boosters. Some providers may not consent to the use of this device
on their network. If you are unsure, contact your provider.
You MUST operate this device with approved antennas and cables as
specified by the manufacturer. Antennas MUST be installed at least 20 cm
(8 inches) from any person. You MUST cease operating this device
immediately if requested by the FCC or a licensed wireless service provider.
You MUST cease operating this device immediately if requested by the USED
or a licensed wireless service provider.
WARNING. E911 location information may not be provided or may be
inaccurate for calls served by using this device. This device may be operated
ONLY in a fixed location for in-building use.
BEFORE USE , you MUST meet all requirements set out in CPC-2-1-05
A subscriber must have the consent of a wireless provider to operate a
Consumer Signal Booster. Subscribers may obtain provider consent in a variety
of ways. For example, AT&T, Sprint, T–Mobile, and Verizon Wireless have
voluntarily committed to allow their subscribers to use properly certificated
Consumer Signal Boosters (i.e., boosters that meet the new rules) on their
networks. Also, a signal booster manufacturer could seek authorization for use
of a particular booster model on behalf of all subscribers of individual
providers. Alternatively, a provider may specify a testing protocol that if
satisfied would result in licensee consent to specific booster models. A
subscriber may also seek a licensee’s express consent to operate a signal
booster, e.g., by phone call or e-mail
The following selected information about wireless providers’ Consumer Booster
registration mechanisms supplements the requirements and information, and the
FCC Signal Boosters website (http://wireless.fcc.gov/signal-boosters/).
Sprint Nextel will allow consumers to register their signal boosters by
calling their toll-free number. They have already trained their calling center
and have designated an engineer to handle inquiries. They may eventually allow
consumers to register on their website but they want to gauge how the process
works via phone first.
-
T-Mobile online registration link: (www.T-Mobile.com/BoosterRegistration);
(https://saqat.t-mobile.com/sites/SignalBooster#). -
Verizon’s online registration link:
(http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html). -
AT&T will allow online registration and will inform OET Lab with the web link when it is ready.
-
U.S.Cellular:
(http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp).
WARRANTY
Warranty information applicable to your Booster
- Warranty Period: 2 year.
- Type of Warranty Service: Customer Replaceable Unit and Customer Carry-In or Mail-In Service.
- ANNTLENT Company is not responsible for Shipping Cost.
For Warranty service consult the telephone list at www.ANNTLENT-
tech.com/contact us.
What this Warranty Covers
ANNTLENT warrants that each Machine 1) is free from defects in materials and
workmanship and 2) conforms to ANNTLENT’s Official Published Specifications
which are available on request.
The warranty period for the Machine starts on the original date of
installation. The date on your invoice or sales receipt is the date of
installation unless ANNTLENT or your reseller informs you.
This warranty does not cover the following:
Failure resulting from misuse, accident, modification, unsuitable physical or
operating environment, or improper maintenance by you;
The warranty is voided by removal or alteration of identification labels on
the Machine or its parts.
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certification/registration number only signifies
that the Industry
Canada technical specifications were met. This product meets the applicable
Industry Canada technical specifications.
This product meet all requirements set out in CPC-2-1-05, URL:
http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html
Copyright Information
© 2020 Copyright ANNTLENT Technology (Shenzhen) Co., Ltd.
The information contained in this document is subject to change without
notice.
Edition 5, 6/2020
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>