SEALEY 4040AB 4Tonne Trolley Jack with Rocket Lift Instruction Manual

: June 10, 2024
: SEALEY

Table of Contents

SEALEY 4040AB 4Tonne Trolley Jack with Rocket Lift
Product Information
Specifications
Product Usage Instructions
SAFETY
ASSEMBLY
OPERATION
MAINTENANCE
ENVIRONMENT PROTECTION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SEALEY 4040AB 4Tonne Trolley Jack with Rocket Lift

Product Information

The Sealey 4 Tonne Trolley Jack with Rocket Lift (Model No. 4040AB, R.V2, G, Y, O.V3. Series) is manufactured to a high standard and designed to provide years of trouble-free performance when used according to the instructions provided.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE

INTRODUCTION
Single-piece hydraulic unit with heavy base design and large jacking saddle. Universal joint release mechanism allows safer, more controlled lowering of the jack. Rocket Lift feature brings lifting arm into contact with jacking point with minimal pumps. Polyurethane wheels for smoother manoeuvrability and helps prevent damage to workshop floor. Magnetic wheel nut retention tray. Protective jack handle sleeve helps prevent accidental damage to car bodywork when pumping the handle. Range available in five different colours. 2 Year Guarantee – 2nd year subject to T&Cs and registration on website (www.sealey.co.uk).

Specifications

Model Nos: …………….. 4040AB,G,O,R.V2, Y.V3.SERIES
Capacity: 4 tonne
Minimum Saddle Height: 100mm
Maximum Saddle Height: 533mm
Maximum Chassis Height: 162mm
Length: 751mm
Optional rubber jack pad (not supplied) ………………JP17

Optional rubber jack pad (JP17) is not supplied with the product.

Product Usage Instructions

Before using the jack, ensure that it is in sound condition and good working order. Take immediate action to repair or replace damaged parts using genuine parts only. The use of improper parts can be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well-lit working area that is clean and tidy, and free from unrelated materials.
Ensure that the ground surface is level, solid and preferably concrete. Avoid using tarmacadam as the jack may sink in. Chock the wheels of the vehicle.
The vehicle’s handbrake should be engaged, engine switched off, and transmission in gear (or PARK if automatic).
Ensure that there is a minimum distance of 0.5m between the vehicle and static objects such as doors, walls, etc., allowing for vehicle tilting.
Ensure that there are no passengers in the vehicle and all non-essential persons keep a safe distance while the jack is in use.
Place the jack only at those lifting points recommended by the vehicle manufacturer (see vehicle handbook).
Check that the lifting point is stable and centered on the jack saddle.
Ensure that the jack wheels are free to move, and there are no obstructions.
Use the jack for lifting only, NOT for supporting the lifted load. Use suitable axle stands under the vehicle before proceeding with any task.
Use a qualified person to lubricate and maintain the jack. Ensure that only hydraulic jack oil is used in the jack.
Do not operate the jack if damaged, or allow untrained persons to operate the jack, or exceed the rated capacity of the jack.
Do not allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.
Do not jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
Do not work under the vehicle until appropriately rated axle stands have been correctly positioned. Do not adjust the safety overload valve.
When not in use, store the jack fully lowered in a safe, dry, childproof area.

By following these instructions carefully, you can ensure safe and correct usage of your Sealey Trolley Jack with Rocket Lift and enjoy years of trouble- free performance. For further information, please refer to the user manual provided.

SAFETY

Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use genuine parts only. The use of improper parts may be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit working area.
Keep working area clean and tidy and free from unrelated materials.
Use jack on level and solid ground, preferably concrete.
Avoid tarmacadam as jack may sink in. Chock wheels of vehicle.
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
Ensure there are no passengers in the vehicle.
Place jack under only those lifting points recommended by vehicle manufacturer (see vehicle handbook).
Check that the lifting point is stable and centred on the jack saddle.
Ensure the jack wheels are free to move and that there are no obstructions.
DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
Use suitable axle stands under the vehicle before proceeding with any task.
Use a qualified person to lubricate and maintain the jack.
Ensure that only hydraulic jack oil is used in the jack.
DO NOT operate the jack if damaged.
DO NOT allow untrained persons to operate the jack.
DO NOT exceed the rated capacity of the jack.
DO NOT allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.
DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
DO NOT work under the vehicle until appropriately rated axle stands have been correctly positioned.
DO NOT use the jack for purposes other than that for which it is intended.
DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.
DO NOT adjust the safety overload valve.
When not in use store jack, fully lowered, in a safe, dry, childproof area.

ASSEMBLY

Insert the upper handle into the lower handle, until the push button locates in the lower handle hole (fig.1).
Undo the handle socket screw fig.2 (B) until it no longer protrudes into the handle socket.
Insert the pump handle into the handle socket, engaging the square drive of the release valve.
Ensure that the handle is correctly inserted into the socket, then tighten the handle socket screw (B).

HYDRAULIC SYSTEM PURGING

Open the release valve by turning it one full turn counter-clockwise.
Pump the handle a minimum eight full strokes.
Close the release valve by turning it clockwise.

OPERATION

WARNING! Before use ensure you have read, understood and applied Section 1 safety precautions.
IMPORTANT: Before use, the operator is to visually inspect the jack for cracked welds, damaged or missing parts or hydraulic leaks.

RAISING A VEHICLE
We recommend that efforts of raising the load shall be reduced by the use of assistance during this operation.
Ensure that the jack and the vehicle are on a hard, level surface.
Always ensure that the vehicle handbrake is engaged and that the vehicle wheels are chocked.
Consult the vehicle manual to determine the location of jacking points.
Position the jack under a suitable lifting point.
Turn the slow release valve clockwise, to the closed position (fig.3). DO NOT over-tighten.
Raise the vehicle to the desired height by pumping the handle up and down.
Place axle stands beneath the locations recommended by the vehicle manufacturer.
Turn the release valve slowly counter-clockwise to lower the vehicle on to the axle stands.
LOWERING A VEHICLE
Turn the release valve clockwise to the closed position.
Pump the handle to raise the vehicle off the axle stands.
Remove the axle stands from beneath the vehicle.
Turn the release valve slowly counter-clockwise to lower the vehicle to the ground.
NOTE: When not in use, ALWAYS leave the saddle and ram fully retracted. Also be aware jack is now fitted with a slow release mechanism for controlled lowering.

MAINTENANCE

IMPORTANT: Only fully qualified personnel should attempt maintenance or repair.

MONTHLY MAINTENANCE
Lubrication is critical to jacks. Any restriction due to dirt or rust can cause either slow or extremely rapid jack movement, causing damage to the internal components.
Lubricate the ram, all of the pivot points, the linkages and the saddle and pump mechanism with light oil.
Grease the wheel bearings and axles.
Keep all jack surfaces and warning labels clean.
Check and maintain the ram oil level (Section 7.3).
THREE MONTHLY MAINTENANCE
At three monthly intervals, check the ram for any signs of rust or corrosion. Clean the ram as required and wipe with an oiled cloth.
CHECKING THE OIL LEVEL
Fully retract the ram by turning the release valve counterclockwise.
With the jack in the level position, remove the oil filler plug (fig.4).
The oil should be level with the bottom of the oil filler hole. If it is not, top up with clean hydraulic jack oil.
Replace the oil filler plug and check the jack operation.
Purge air from the hydraulic unit as required. Refer to Section 5.
NOTE: Always store the jack in the fully lowered position. This will protect critical areas from excessive corrosion. Owing to their size and weight, hydraulic products should ideally be repaired by local service agents. We have service/repair agents in most parts of the UK. Before returning your product please call our technical helpline on 01284 757505 for advice and troubleshooting guidance. If the jack is under guarantee please contact your stockist.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 24 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk