Shelly Plus Wall Dimmer User Guide

: June 10, 2024
: Shelly

Table of Contents

Shelly Plus Wall Dimmer
Product Information
Product Usage Instructions
Read before use
Product Introduction
Installation Instructions
initial Inclusion
Operating Instructions
Specification
Disposal & Recycling
FCC Notes
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shelly Plus Wall Dimmer

Product Information

The Shelly Plus Wall Dimmer Load is an advanced wall dimmer switch that allows you to control the brightness of your lights with ease. It features a removable faceplate, a slider with a brightness indicator, and a power button with power and Wi-Fi indicators. The switch is designed to be mounted in a wall gang box and requires a live, neutral, and ground wire for proper installation. It operates on a frequency range of 2412-2462 MHz (max. 2495 MHz) and comes with a supplied antenna to maintain compliance with FCC’s RF Exposure guidelines.

Product Usage Instructions

Turn off the power to the circuit that you will be working on.
Remove the existing wall dimmer switch from the gang box.
Connect the live wire from the circuit to the live terminal on the Shelly Plus Wall Dimmer Load.
Connect the neutral wire from the circuit to the neutral terminal on the Shelly Plus Wall Dimmer Load.
Connect the ground wire from the circuit to the ground terminal on the Shelly Plus Wall Dimmer Load.
Insert the Shelly Plus Wall Dimmer Load into the gang box and secure it with screws.
Attach the supplied antenna to the switch.
Attach the faceplate to the switch.
Turn on the power and use the slider to control the brightness of your lights.

Remember to maintain a minimum distance of 20cm between the switch and your body to comply with FCC’s RF Exposure guidelines.
Use only the supplied antenna for optimal performance.

Read before use

This document contains Important technical and safety Information about the device, its safety use and installation

CAUTION! Before beginning the installation please read the accompanying documentation carefully and completely. Failure to follow recommended procedures could lead to malfunction, danger to your life or violation of the law. Alterio Robotics is not responsible for any loss or damage in case of
incorrect installation or operation of this Device.

Product Introduction

Shelly® is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits through a mobile phone, tablet, PC,
or home automation system. Shelly® devices can work standalone on a local Wi- Fi network or be operated through cloud home automation services, MQTT, UDP or other protocols. Shelly® devices can communicate directly with other Wi-Fi devices through HTTP protocol. An API is provided
by Alterio Robotics EOOD. For more information, please visit: https://shelly- apl-docs.shelly.cloud/#shelly-famlly-overvlew. Shelly® devices can
be accessed, controlled and monitored remotely from any place where the User has internet connectivity, as long as the devices are connected to a
Wi-Fi router and the Internet. Shelly® devices have embedded Web Interface accessible at http://192.168.33.1 when connected directly to the device’s
access point, or at the device’s IP address on the local Wi-Fi network. The embedded Web Interface can be used to monitor and control the device, as
well as adjust its settings.

Shelly Cloud is our service that can be accessed using either Android or iOS mobile application, or with any internet browser
at https://homa.shally.cloud/. Shelly Plus® Wall Dimmer (the Device) can switch on/off and vary the brightness of compatible dimmable bulbs. It can be easily wired in the place of a standard light switch.

Installation Instructions

CAUTION! The product is intended for indoor use only.
CAUTION! Protect the product from dirt and moisture! Do not use the product in a damp environment!
CAUTION! Danger of electrocution. The mounting/installation of the Device should be done by a qualified person (electrician).
CAUTION! Do not connect the Device to circuits exceeding the given max load!
CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
CAUTION! Use the Device only with power grid and appliances which comply with all applicable regulations. Short circuit in the power grid or any appliance connected to the Device may damage the Device.

initial Inclusion

Verify that the circuit breaker is turned off and no voltage is present on its output terminals.
Remove the existing light switch wall plate and light switch.
Make sure that a neutral wire is present in the gang box. If neutral is present, disconnect the existing light switch, making note of the line and load wires.
Connect the following wires from the Shelly Plus Wall Dimmer Switch to your circuit:
Green wire connects to the Ground wire.
- White wire connects to the Neutral wire.
- Black wire connects to the incoming Live wire.
- Red wire connects to the load wire.
Fix firmly the Shelly Plus Wall Dimmer to the gang box with the included screws.
Install the new wall plate.
Turn on the circuit breaker.
When the Device is powered on, the power indicator will turn on and the brightness indicator dots will illuminate one by one. The dot corresponding to the brightness level before the Device has been powered off will stay illuminated.
Press the power button. The power indicator will turn white, and the brightness indicators will display a vertical bar of illuminated dots. The Shelly Plus Wall Dimmer is ready to be added to the Shelly app.

Operating Instructions

Switch the lights on or off by pressing the power button.
Swipe your finger up or down the slider to adjust the brightness of the lights. The brightness indicator will display the current status with a vertical bar of illuminated dots. The highest of the dots stays illuminated after the lights are switched off.

In order to reserve boot the Device, press and hold the power button for 5 seconds while powered. For factory reset press and hold the power button for 10 seconds.

If you choose to use the Device with the Shelly Cloud mobile application and Shelly Cloud service, instructions how to connect the Device to the Cloud and control It through the Shelly App can be found in the “App Guide”. Shelly Mobile Application and Shelly Cloud service are not conditions for the Device’s proper functioning. This Device can be used stand-alone or with various other home automation services and applications.

CAUTION! Do not allow children to play with the buttons/switches connected to the Device. Keep the Devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.

Specification

Product Dimensions (HxWxD): 4.72 x 2.75 x 1.5 inch
Item Weight: 13.4 ounces
Material: ABS+PU
Color: White
Voltage: 100-120 VAC
Frequency: 50/60 Hz
Maximum Wattage: 400 W (Incandescent), 150 W (LED and CFL)
Radio protocol: Wi-Fi 802.11 b/g/n
Radio signal power: 1 mW
Frequency Wi-Fi: 2412-2462 MHz; (Max. 2495 MHz)
RF output Wi-Fi: < 15 dB
Operational range (depending on terrain and building structure): up to 165 ft outdoors, up to 100 ft indoors
Bluetooth: v4.2
Bluetooth modulation: GFSK, n/4-DQPSK, 8-DPSK
Frequency Bluetooth: TX/RX: 2402- 2480 MHz (Max. 2483.5MHz)
RF output Bluetooth: < 5 dB
Scripting (mjs): Yes
MQTT:Yes
Webhooks (URL actions): 20 with 5 URLs per hook
Schedules: 20 with 5 calls per schedule
CPU: ESP32
Flash:4MB

Disposal & Recycling

This refers to the waste of electrical and electronic equipment. It is applica- i the US and other countries to collect waste separately.

This symbol on the product or in the accompanying literature indicates that the product should not be disposed of in the daily waste. Shelly® Plus Wall Dimmer must be recycled to avoid possible damage to the environment or human health from uncontrolled waste disposal and to promote the reuse of materials and resources. It is your responsibility to dispose of the device separately from general household waste when it is already unusable.

FCC Notes

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification or change to this equipment. Such modifications or change could void the use(s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against hannful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF exposure statement:
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Chemi vrah Blvd.
Tel.: +359 2 988 7435
E-mail: [email protected]
Web: https://www.shelly.cloud
Changes in the contact data are published at the official website of the Manufacturer.
https://www.shelly.cloud