OLIGHT Javelot Pro 2 Hunting Kit User Manual
- June 10, 2024
- OLIGHT
Table of Contents
OLIGHT Javelot Pro 2 Hunting Kit User Manual
Thank you for purchasing this Olight product. Please read this manual carefully before use and keep it for future reference!
IN THE BOX
SPECIFICATIONS
All performance measurements in accordance with ANSI/NEMA FL1-2009 standards. Stated data were been measured indoor under 25 degrees celsius, windless laboratory conditions. The data may vary due to environmental and heat dissipation conditions.
Note: The maximum output brightness will decrease as the battery voltage decreases.
USB MAGNETIC CHARGING CABLE — MCC3
PRODUCT OVERVIEW
BEFORE FIRST USE
Please remove the protective film on the lens, and please also unscrew the body to remove the insulating film within the battery compartment, then screw the body back on tightly.
INDICATORS ON BOTH SIDES
NOTE: While turning on, if the battery power is less than 10%, the lowest indicator on the right side will glow red.
CHARGING
- Before the first use please fully charge the product.
- Connect the USB end of the magnetic charging cable to an external USB power source, then attach the other end of the cable to the charging port of the light (best charging efficiency with a USB power source of no less than 10W (5V 2A). The red indicator means charging, while the green indicator means charging completed (battery level＞95%).
- Only charge with standard MCC3. NOT compatible with other MCC.
SROD LONG COIL WIRE MAGNETIC REMOTE SWITCH
Quickly single click the button to turn the flashlight ON/OFF. When you press and hold the button, the flashlight will be in momentary mode; when you release the button, it will turn off.
DANGER
- DO NOT shine the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
- DO NOT cover the light head when the light is on, or place the light head on the ground. The radiation energy of the light may cause damage to the light itself, or even result in burning to flammable objects.
- DO NOT store the flashlight when its surface is under high temperature.
- When the flashlight is working on the turbo mode, the surface temperature can reach 55°C. At that time, DO NOT touch the hot surface of the head.
WARNING
- Keep out of reach of children.
- DO NOT use the turbo mode continuously when the environmental temperature is high in case the flashlight body is too hot to hold.
- DO NOT short-circuit the tail switch cap with the ring surrounding it in any manner, including placing it in your mouth or licking it with your tongue.
NOTICE
- DO NOT short-circuit the tail switch cap with the surrounding ring. A short circuit in this case will result in a weak electric discharge between them and may lead to a complete battery drain if it is in this state for too long.
- While the flashlight works in the highest brightness level (5 minutes at room temperature) to reach the default temperature limit, the output would gradually reduce to no less than 1,000 lumens to prevent overheating unless the battery is low.
- The output would be capped when the ambient temperature is below 0°C/32.00 °F. Please preheat the flashlight to restore it to fully functional.
- The magnetic tail is easy to attract iron debris. Please keep the tail switch cap and the ring surrounding it clean.
Hazard Hot surface
Human behaviour that is intended to be caused after understanding the safety
sign’s meaning. Taking care to avoid coming into contact with a hot surface.
EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the
usage of the product inconsistent with the warnings in the manual .
HOW TO OPERATE
TAIL SWITCH
Constant Low Mode: Quickly half-press the tail switch to produce a low light
output or turn the light off (if already on).
Momentary Low Mode: Half-press and hold the tail switch to enter momentary on mode and release the tail switch to exit the mode.
Constant Turbo Mode: Quickly full-press the tail switch to enter turbo or turn the light off (if already on). To exit turbo mode, full-press the tail switch again.
Momentary Turbo Mode: Full-press and hold down the switch to enter momentary turbo on mode. Release the switch to exit turbo mode.
SIDE SWITCH
Press and hold the side switch to turn the flashlight on or off. It memorizes
the last mode you selected via the side switch.
When turning on, single click the side switch to cycle through the modes. Starting from the present one, the brightness level will switch to the next one from low to high.
When in turbo mode, single click the side switch to access the low mode.
WARRANTY
Within 30 days of purchase: Contact the original seller for repair or
replacement.
Within 5 years of purchase: Contact Olight for repair or replacement.
Battery Pack: 2 years.
USB Magnetic Charging Cable: 1 year.
This warranty does not cover normal wear and tear, modifications, misuse,
disintegrations, negligence, accidents, improper maintenance, or repair by
anyone other than an authorized retailer or Olight itself.
USA Customer Support
cs@olightstore.com
Global Customer Support
customer-service@olightworld.com
Visit www.olightworld.com to see our complete
product line of portable illumination tools.
Dongguan Olight E-Commerce Technology Co., Ltd
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town,
Dongguan City, Guangdong, China.
Made in China
Read More About This Manual & Download PDF:
References
- Olight | Illuminate Your World.
- Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>