ALDI GLM44A Electric Lawn Mower User Manual

ALDI GLM44A Electric Lawn Mower

Product Information

• Model: GLM44A
• Electric lawn mower
• Produced in China for ALDI Stores Ltd.
• 3-year warranty
• Includes handle grip, pull relief, quick-release lever, collecting bag, connecting piece, carry handle, cutting height lever, motor unit, connection cable, handle mount, discharge flap, fill level indicator, cable clamps, safety switch with power cable, safety bar, and collecting bag handle
• Maximum sound power level: LWA 96
• Protection class II
• IPX4 water-resistant

Product Usage Instructions

1. Read and store the operating manual for future reference.
2. Before use, ensure that the device is properly connected to a properly installed socket.
3. Keep other persons and animals out of the working range while using the device.
4. Do not move the device over the power cable.
5. Always keep the discharge flap closed to avoid injury from cuttings or stones.
6. Do not reach or step underneath the device while it is in operation.
7. Disconnect the device from the mains before carrying out maintenance and cleaning work.
8. Adjust the cutting height lever to the desired height before use.
9. To start the device, turn it on using the ON switch and hold down the safety bar.
10. To stop the device, release the safety bar and turn it off using the OFF switch.
11. After use, disconnect the device from the mains and allow it to cool down before storing.
12. Clean the device thoroughly after each use and store it in a dry, safe place.

Scope of delivery/device components

1. Handle grip (top)
2. Pull relief (for the power cable)
3. Quick-release lever (handle joint)
4. Bottom part of handle
5. Collecting bag
6. Connecting piece (2x)
7. Carry handle
8. Cutting height lever
9. Motor unit
10. Connection cable
11. Handle mount
12. Quick-release lever (handle mount)
13. Discharge flap
14. Fill level indicator
15. Cable clamps (2x)
16. Safety switch with power cable
17. Safety bar
18. Collecting bag handle

General information

Reading and storing the operating manual
This operating manual is part of the electric lawn mower (hereinafter also called “device”). It contains important information on how to set up and use the product.  Before using the device, read the operating manual carefully, in particular the safety instructions. Failure to follow this operating manual may lead to severe injuries or product damage. This user manual is based on the standards and regulations that are valid within the European Union. Outside the EU, please also note the country-specific directives and laws. Keep this operating manual for future reference. If you pass this device on to a third party, you must also supply this operating manual.

Proper use
The device is exclusively designed for mowing private lawns. The lawn must be dry and level. Wildflower meadows, uncultivated meadows and strongly overgrown lawns with high weeds (such as thistles) are not considered lawns. This device is intended for private use only and is not suitable for commercial use. Use the device only as described in this operating manual. Any other use is improper and may lead to product damage or even personal injury. This device is not a toy. The manufacturer or retailer assume no liability for damage caused by improper or incorrect use.

Explanation of symbols

The following symbols and signal words are used in this user manual, on the device or the packaging.

• This symbol provides you with useful additional information on handling and use.
• Declaration of conformity (see chapter “Declaration of conformity”): Products marked with this symbol meet all the applicable Community regulations of the European Economic Area.
• This symbol indicates that the device complies with the protection class II.
• General warning sign.
• Caution! Discharge of cuttings or stones. Always keep the discharge flap closed.
• Warning! Rotating blade! Do not reach or step underneath the device.
• Warning! Electric voltage.
• Read the operating manual.
• Keep other persons and animals out of the working range!
• Disconnect the device from the mains before carrying out maintenance and cleaning work.
• Keep the power cable away from the rotating blade! Do not move the device over the power cable.
• Cutting width of the device.
• The symbol shows the maximum sound power level LWA.
• The device is protected from all sides against water splashes.

Safety

The following signal words are used in this operating manual.

WARNING! This signal symbol/word denotes a hazard with an average risk level that could lead to death or severe injury if it is not avoided.
CAUTION! This signal symbol/word denotes a hazard with a low risk level that could lead to mild or moderate injury if it is not avoided.
NOTE! This signal word provides a warning about potential material damage.

Safety notes

WARNING! Risk of electric shock!
Improper handling of the device, faulty electric installation or excessively high mains voltage may result in an electric shock.

• Only connect the device to a properly installed socket. The mains voltage must match the value indicated on the rating plate.
• In the case of a fault, immediately disconnect the device from the power cable and/or mains.
• Do not connect the device if the device, power cable or a mains plug shows visible signs of damage.
• Damaged power cords and devices must only be repaired by the manufacturer, their customer service or a qualified professional.
• Do not open the housing under any circumstances and never insert any object in the housing.
• Always disconnect the device from the mains before cleaning or servicing it.
• Never touch the mains plug with damp hands.
• Do not immerse the device, power cable or mains plug in water or other liquids.
• Do not bend the power cable and do not pass it over sharp edges.
• Never move the device over the power cable.

Notes on the power cable

• Use only authorised power cables of type H05VV-F or H05RNF.
• They must be approved for outdoor use.
• The length shall not exceed 50 m.
• The power cable wire cross section must be at least 1.5 mm².
• Always completely unroll cable drums before use.
• Check the cable for damage.

WARNING! Danger for children and persons with impaired physical, sensory or mental capacities (e.g. partially disabled persons, older persons with reduced physical and mental capacities) or lack of experience and knowledge. Improper handling of the device can lead to severe injuries or damage to the device.

• This lawn mower may be used by persons with impaired physical, sensory or mental capacities or those lacking experience and knowledge if they are supervised or have been instructed in how to safely use the lawn mower and have understood the risks associated with operating it. Children must not play with the lawn mower. Cleaning and user maintenance must not be performed by children.
• Never allow children or other persons, who are not familiar with the user manual, to use the lawn mower. Local provisions can define the minimum age of the user.
• Do not leave the lawn mower unattended while in operation.

CAUTION!
Risk of injury!
Improper handling of the device can cause injuries.

• The blade is sharp; take care when touching the blade.
• Do not reach underneath the device or into the discharge chute.
• Do not operate the device when other persons or animals are around.
• Do not operate the device if you are impaired (e.g. under the influence of drugs, alcohol, medication or if you are tired).
• Wear solid shoes, long trousers and hearing protection.
• Watch out for the power cable as you might trip over it and lose control of the device.
• Avoid working on wet grass as you might slip and lose control of the device.
• Do not work on areas with an inclination above 20 % as you might slip and lose control of the device.
• Always keep the discharge flap closed and keep away from the discharge chute when working without a collecting bag.
• Wait until the blade stands still before removing any blockage or clogging and carrying out any other work on the device.

Before first use

Check the device and scope of delivery

WARNING! Danger of suffocation!
Children may become tangled up in the packaging film when playing with it and suffocate.

• Do not let children play with the packaging film.

NOTE! Risk of damage!
If opening the packaging with a sharp knife or other pointed objects, careless handling can damage the device.

• Therefore, be very careful when opening.

1. With both hands, lift the device out of the packaging.
2. Check that the delivery is complete (see chapter “Scope of delivery/device components”).
3. Inspect the device and individual parts for damage. Do not operate a damaged device; instead, contact the manufacturer via the service center listed on the warranty card.

Mounting the handle
The handle is awkwardly shaped. Have a second person help you attach the handle.
Mounting the bottom part of the handle on the lawn mower

1. Slide the pull relief 2 onto the bottom part of the handle 4.

2. Slide the connecting pieces 6 onto the bottom part of the handle 4 . The locking washers of the connecting pieces must point inwards.

3. Place the bottom part of the handle on the handle mount 11. Check whether the serrations of the locking washer engage correctly in the handle mount. The holes of the handle mount, the connecting pieces and the bottom part of the handle must point towards each other.
   4. Twist the quick-release levers 12 into the handle mount 11. Do not use excessive force; it is sufficient to twist in the quick-release lever until you feel a resistance.

4. Flick the quick-release lever 12. If it is too tight, turn the quick-release lever one turn backwards. The bottom part of the handle is connected to the lawn mower and does not wobble.

Mounting the handle grip on the bottom part of the handle

1. Position the pull relief 2 on the crossbar of the handle bottom part 4 .
2. Place the handle grip 1 onto the bottom part of the handle 4 . The connection cable must not lay between the handle parts and should run beneath the handle instead.
3. Align the holes of the handle parts with each other and push the screws 3a from the inside through the handle.
4. Put the washers 3b onto the screw and turn the quick-release levers 3 approximately 5 to 7 turns.
5. Align the handle grip 1 straight on the bottom part of the handle 4 and keep it in position.
6. Align the screw heads. The screw heads are bent and latch into the handle bar.
7. Flick the quick-release levers 3 . If it is too tight, turn the quick-release lever one turn backwards.
8. Check whether the handle grip 1 is aligned and connected to the bottom part of the handle 4 without wobbling.
9. Attach the connection cable 10 with two cable clamps 15 onto the handle frame. The connection cable must run beneath the crossbar of the bottom part of the handle. The handle parts are mounted and solidly connected.

Preparing the collecting bag
The collecting bag is partially assembled on delivery.

1. Insert the collecting bag handle 18 into the recesses on the top of the collecting bag 5.
2. Pull the plastic rims of the collecting bag 5 from the inside over the steel frame.
3. Check whether the plastic rims are properly in place on all sides.
4. Completely lift the discharge flap 13 (see Fig. E right).
5. Hang the collecting bag 5 onto the hooks above the discharge chute again.
6. Check whether the collecting bag is properly fitted 5.
7. Move the discharge flap 13 carefully until the collecting bag 5 is covered again.

Operation

Rules of operation
The following rules must be observed at all times when working on and with the lawn mower.

• Do not adjust the device or rectify faults when it stands still. Make sure that the device cannot start up.
• Only lift the device on the grip and handle. Never reach underneath the device to lift it.
• Let the blade run to a stop before touching the device or the collecting bag again.
• Never reach beneath the discharge flap or into the discharge chute.
• Stop the motor immediately if you notice unusual mowing sounds or vibrations. Check and rectify cause of the fault before resuming mowing.
• Never put a damaged device into operation. Any damage to the blade and the device must be repaired by the manufacturer’s customer service or qualified personnel.
• Mow diagonally to inclinations.

Note the following when mowing and mulching
The following instructions help you use the device effectively and safely. Improper handling of the device can cause damage to it.

• The device can be operated with or without collecting bag. You should only operate the device without the collecting bag (mulching) when trimming the lawn just a little shorter (max. 2 cm).
• Mow slowly and try not to use the entire cutting width to cut the grass evenly at high rotation speed. A high cutting load reduces the blade’s rotation speed.
• Remove any branches, pegs, stones, strings and mounds (molehills) before mowing to safeguard the device.
• Always mow in the direction facing away from the power supply and the power cable.
• Always push the device forward; pulling the device might damage the power cable.

Adjusting the handle position
The handle can be adjusted to a comfortable working height. Adjust the handle to your individual working height before working with the device.

1. Undo the two quick-release levers 12 on the handle mount.
2. Set the handle to the desired height.
3. Check whether the serrations of the locking washer engage correctly in the handle mount 11.
4. Flick the quick-release levers 3.

Adjusting the cutting height
You can set the cutting height between approximately 20 and 70 mm. The cutting height lever 8 can be engaged in 7 positions.

1. Hold the device by the carry handle 7.
2. Pull the cutting height lever 8 out of its arrester.
3. Slide the cutting height lever 8 to the desired level. The device lifts or lowers.
4. Engage the cutting height lever 8 properly again.

Preparing for operation
Only use an extension cable if the included cable is insufficient for mowing the entire lawn. Avoid using more than one extension cable.

1. Check the device, the collecting bag and the blade before connecting the power supply.
2. Set the desired cutting height before connecting the power supply.
3. Check the handle position and correct it if necessary to work comfortably.
4. Lay out the power cable all along the perimeter of your lawn.
5. Secure the power cable on the pull relief 2 (see Fig. H ).
6. Plug the power cable plug into a properly installed socket.

Turning the motor on and off
Caution! Blade keeps moving The motor is activated by means of a safety switch. When you let go of the safety bar, the motor stops. Only turn on the motor on the grass.

1. Place the device on the grass.
2. Press and hold the button of the safety switch 16 .
3. Pull the safety bar 17 towards the handle. The motor starts.
4. Let go of the safety switch button and keep the safety bar pressed to the handle as long as you operate the motor.
   Letting go of the safety bar stops the motor. The blade keeps running. Wait until the blade has stopped before handling the device.

Emptying the collecting bag
The collecting bag has a fill level indicator 14 . The fill level indicator rises when the motor is running and the collecting bag is empty. Once the collecting bag is full, the fill level indicator rests again on the collecting bag. Empty the collecting bag.
If cuttings remain on the ground, empty the collecting bag as well.

1. Stop the motor and wait until the blade stands still.
2. Lift the discharge flap 13 until the collecting bag 5 is exposed.
3. Lift the collecting bag 5 off the lawn mower. Slightly lift the collecting bag to release it.
4. Move the discharge flap 13 properly until the discharge chute is covered again. Do not simply let go; the discharge flap may get damaged due to the spring action.
5. Empty the collecting bag 5 completely. Clear cuttings of the fabric as best as possible so that the expelled air can escape properly.
6. Completely lift the discharge flap 13.
7. Hang collecting bag 5 onto the hooks above the discharge chute again.
8. Check whether the collecting bag is properly fitted 5.
9. Move the discharge flap 13 carefully until the collecting bag 5 is covered again.

Cleaning

WARNING! Risk of electric shock!
Moisture in the device may cause a short circuit or electric shock.

• Before cleaning, disconnect the power cable from the socket.
• Make sure that no water or other liquid gets inside the housing.
• Never clean the device with running water (e.g. a garden hose).

NOTE! Improper cleaning can damage the device.

• Do not use any harsh cleaning products, brushes with metal or nylon bristles, or sharp or metallic cleaning materials such as knives, hard scrapers or similar. They may damage the surfaces.
• Remove wet cuttings immediately. Residues of wet cuttings on and in the device may harden and cause mould.

Cleaning and inspection after each use
Regular cleaning and inspection is necessary to keep the device in perfect state.

1. Stop the motor and wait until the blade stands still.
2. Disconnect the device by unplugging the power cable and remove the power cable from the pull relief 2.
3. Thoroughly empty the collecting bag 5 (see “Emptying the collecting bag”) without reattaching it to the device.
4. Remove cuttings from the device and the collecting bag 5 with a hand brush.
5. Tip the device on its side and remove cuttings from the discharge chute and blade compartment with a hand brush or a brush.
6. Check the blade for damaged spots and wear. Do not operate the device with a damaged or worn blade! If necessary, have the blade sharpened or exchanged in a specialist workshop (for the blade type, see “Technical specifications”).
7. Set the device upright again.
8. Check all connections (handle, collecting bag) for tight fit.

Maintenance

Apart from the measures described in the section “Cleaning and inspection after each use”, the device is principally maintenance-free. You do not have to lubricate or readjust any parts.
In addition, check the following once a year:

• Free wheel movement.
• Function and free movement of the cutting height adjuster 8.
• Function and free movement of the discharge flap 13.
• Damage to the device, such as broken housing parts or worn collecting bag 5.

If you detect any defects, contact customer service or a specialist workshop. Do not operate the device with a detected defect.

Storage

NOTE! Improper storage of the device can result in damage.

• Let the device dry before storing it. Residual moisture and cuttings remaining in the device can lead to mould formation.

Optionally, the handle can be folded in to save space during storage or transport.

Folding in the handle

1. Release the quick-release levers 12 on the handle mount 11.
2. Take the serrations of the locking washer out of the handle mount 11 by lifting it slightly and then set down the handle on the device.
3. Release the quick-release levers 3 in the centre of the handle.
4. Carefully fold the handle. Watch out for the connection cable. It must not be pinched between the handle parts.

Storage conditions

• Thoroughly clean the device (see “Cleaning”).
• Store the device in a clean, dry, frost-protected place out of the reach of children.
• Store the device in a location away from sunlight and other heat sources.
• Always store device parts and accessories together with the device.
• Store the device and accessories at a temperature between +5 °C and +20 °C.

Transport instructions

• Always transport the device with the handle folded in (see “Folding in the handle”).
• Only lift the device by the carry handle 7.
• Exclusively transport the device in normal position; prevent tilting while transporting.
• When transporting the device in vehicles, the device must be secured in accordance with the applicable regulations (load securing).

Troubleshooting

Technical data

• Model GLM44A
• Rated voltage/frequency: 230–240 V~/50 Hz
• Rated power: 1800 W
• Protection class: II
• IP rating: IPX4
• Max. rpm: 3500 min-1
• Weight (Net): 16.5 kg
• Dimensions (H x L x W) 1160 × 1180 × 475 mm
• Cutting width: 440 mm
• Mowing length setting: 20–70 mm
• Guaranteed sound power level LwA: 96 dB(A)
• Sound power level LwA: 93.04 dB(A)
• Uncertainty KwA 1.2 dB(A)
• Sound pressure level LpA: 83.0 dB(A)
• Uncertainty KpA: 3 dB(A)
• Vibration emission value: 2.887 m/s² (K = 1.5 m/s²)
• Blade type: SMV 1253482000
• Item number: 814142

The noise and vibration values were determined in accordance with EN 60335-2-77:2010.
The vibration emission values during actual use of the device may deviate from the declared values. This is independent of the way the device is used. Users must take all safety precautions to protect themselves. They must consider all influences of the actual application conditions (especially all parts of the work cycle such as running times, idling times and times at which the machine is shut off). The vibration values may deviate from the stated total output depending on the actual use of the device.
Suitable measures include regular maintenance and servicing of the device, keeping your hands warm, taking regular breaks and properly planning the work sequences!

Declaration of conformity

Disposal

Disposing of packaging
Dispose of packaging according to type. Sort the paperboard and cardboard as waste paper and the film as recyclable material.

Dispose of old electrical device
This symbol indicates that this product may not be disposed of together with domestic waste in compliance with the (2012/19/EU) Regulation about waste electrical and electronic devices (WEEE). This product must be handed in at a collection point intended for the purpose. This can occur, for example, by handing it in at an authorised collecting point for the recycling of waste electrical and electronic equipment. Owing to potentially hazardous substances that are frequently contained in waste electronic equipment, incorrect handling of waste equipment may hurt the environment and on the health of human beings. By disposing of this product correctly, you are also contributing towards an efficient use of natural resources. Information on collecting points for waste equipment can be obtained from your local authority, an authorised institution for the disposal of waste electrical and electronic equipment or the waste collection services.

Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly. In the event of product failure within its intended use over the course of the first 3 years after date of purchase, we will remedy the problem as quickly as possible once it has been brought to our attention. In the unlikely event of such an occurrence, or if you require any information about the product, please contact us via our helpline support services, details of which are to be found both in this manual and on the product itself.

ALDI STORES (IRELAND) LTD.
PO BOX 726, NAAS, CO. KILDARE
Visit us at www.aldi.com

AFTER-SALES SUPPORT
+44(0) 1904727501
+353(0) 19022605
support@coreservice.co.uk

References

• Welcome to ALDI

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>