ELITEPROJECTOR Sport MGFU-S MosicGO Outdoor Ultra Short Throw UST Projector User Guide

ELITEPROJECTOR Sport MGFU-S MosicGO Outdoor Ultra Short Throw UST

Projector

Product Information

The Sport MGFU-S Lite MGFU-L projector from EliteProjector is a versatile device that can be used for movies, music, and presentations. It features ventilation ports on the sides and bottom to prevent overheating, and it is available in two models: Sport MGFU-S Lite and MGFU-L. The projector should not be used in confined spaces or on cluttered surfaces as this can restrict airflow and cause damage to the device.

Eye Safety Warnings
The projector emits a powerful light beam that can cause retinal damage if stared into directly or indirectly. It is recommended to use a laser pointer or pointer stick instead of standing in the projector’s light beam to a point on the screen. Students and other viewers should also be advised to stay out of the direct light beam. Window blinds should be used, and interior light sources should be turned down to reduce the washout glare of ambient light.

Important Safety Instructions

It is important to not block the ventilation ports located on the sides and bottom of the projector to prevent overheating. The projector should not be used if it has been physically damaged or abused, such as being dropped or exposed to rain or moisture. The unit should only be repaired by authorized service personnel, and opening or removing covers may expose dangerous voltages or other hazards. It is recommended to follow all warnings and cautions in the manual and on the projector to ensure safe usage.

1. The ventilation ports prevent overheating. Never block these ports located on the sides and bottom of the projector. (See page 12) Direct obstruction, confined spaces or placing on a cluttered surface restricts airflow and ruins the projector.

2. To reduce risk of fire or electric shock, do not expose the projector to any liquids, rain, snow or airborne moisture.

3. Do not use the projector in direct sunlight.

4. Do not use the projector in areas susceptible to excessive dust and dirt.

5. Turn off the product before cleaning.

6. Disconnect the power cord if the product is not being used for a long period.

7. Ensure that the ambient room temperature is within 0- 40°C (32-104°F).

8. Ensure that relative humidity is 5 – 35°C (41- 95°F), 80% (Max.), and non-condensing.

9. Do not drop, throw or try to bend your product.

10. Clean only with a dry cloth.

11. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to):

    • The unit has been dropped.
    • The charger or plug has been damaged.
    • Liquid has been spilled on the projector.
    • Projector has been exposed to rain or moisture.
    • Something has fallen into the projector or something is loose inside. Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact your
      local reseller or service center before you send the unit for repair.

12. Follow all warnings and cautions in this manual and on the projector.

13. The unit should only be repaired by appropriate service personnel.

14. Projector lamps generate a lot of heat. This causes much of the projector’s surface area to heat up. If the projector seems to be excessively hot, turn it off so that it can cool down and then call customer service.

CAUTION
RISK OF BATTERY EXPLOSION IF INCORRECT TYPE IS USED. MAKE SURE TO PROPERLY DISCARD USED BATTERIES ACCORDING TO LOCAL REGULATIONS.

COPYRIGHT/TRADEMARK

© Copyright 2019. All rights reserved.
The manufacturer reserves the right to make technical changes. The manufacturer assumes no liability for damages incurred directly or indirectly from errors, omissions, or discrepancies between the device and this documentation. Other brands or logos are trademarks or registered trademarks of their respective companies.

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this projector conforms to the following directives and norms:

• EMC Directive 2014/30/EU
• ErP Directive 2009/125/EC
• EMC:
  • EN 301489-1
  • EN 301489-17
  • EN 55032
  • EN 55024
• Low Voltage Directive: 2014/35/EU
• Safety: EN 62368, EN62133+Annex.M

TRADEMARKS
Apple, Macintosh, iPod, iPod nano, and iPhone are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated.

NOTE:
This product is covered electrical and electronic equipment under the European Union’s Waste from Electrical and Electronic Equipment (“WEEE”) Directive (2002/96/EC). The WEEE Directive requires that covered equipment be collected and managed separately from typical household waste in all EU member states. Please follow the guidance of your local environmental authority or ask the shop where you purchased the product for collection or recycling options.

FCC STATEMENT WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved may void authority to operate the equipment.

FCC CAUTION
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

AGENCY APPROVALS
FCC, CE, and LVD

Other specific Country Approvals may apply. Please see product certification label.

Input ratings: AC 100 – 240V, 6.3A, 50 – 60Hz

Product offerings and specifications may be altered at any time without notice.

Product Usage Instructions

1. Connect the power cord to the projector and plug it into an electrical outlet.
2. Connect the video or audio source to the projector using the appropriate cable.
3. Adjust the focus and keystone correction as needed to get a clear image on the screen.
4. Use the menu buttons on the projector or the remote control to adjust settings such as brightness, contrast, and color.
5. Start playing your movie, music, or presentation.
6. When finished, turn off the projector and unplug it from the electrical outlet.

It is important to not block the ventilation ports on the sides and bottom of the projector to prevent overheating. Do not attempt to service the unit yourself, and only use attachments/accessories recommended by the manufacturer. If the projector seems excessively hot, turn it off and let it cool down before using it again.

PRODUCT OVERVIEW

1. Kensington Lock Slot
2. Ventilation Port
3. USB Type C POWER OUT
4. USB
5. 12V Trigger (To Screen)
6. DC IN 19V
7. Power On/Off Switch
8. USB Type C Display Port (DP)/USB Type C PONER OUT
9. HDMI 2
10. HDMI 1
11. Earphone Jack
12. Touch Keypad
13. Focus Ring
14. Ventilation Port
15. Tripod Mount Hole
16. Wireless Speaker Indicator
17. Projector Indicator
18. Wireless Speaker On /Off Button
19. Projector On /Off Button
20. Battery / Power Status Indicator (Battery indicator only for MGFU-S model)
    Note:
    Follow the steps to open I/O cover.

Touch Keypad

1. Up (adjust keystone up)
2. Down (adjust keystone down)
3. Right
4. Left
5. OK/Enter
6. Menu
7. Mute
8. Input Source Selection
9. Home

Remote Control

1. Wireless Speaker On/Off, Audio Source Selection(Note)
2. Projector On/Off, Brightness Adjustment (Note)
3. Up
4. Down
5. Right
6. Left
7. OK/Enter
8. Adjust Keystone Up
9. Adjust Keystone Down
10. Menu
11. Home
12. Video Source Search
13. Audio Source Search
14. HDMI1
15. HDMI2
16. DP
17. Mute
18. Volume Down
19. Volume Up
20. Wireless Audio Input
21. Projector Audio Input
    • No Function

Note:

• When the projector is off, short press the PJ button on the remote control to turn on the projector.
• When the projector is ON, short pressing the PJ button on the remote control will cycle through the following brightness modes: MAX, ECO, and MIN.
• When the projector is on, long press the PJ button on the remote control over 1 second after prompt message and then short press the PJ button again to turn off the projector.
• When Wireless Speaker is off, short press the BT button on the remote control to turn on Wireless Speaker.
• When Wireless Speaker is on, long press the BT button on the remote control for over 1 second to turn it off Wireless Speaker.
• When both of projector and wireless speaker are ON, short pressing the BT button will cycle through the source of the speaker between the projector and wireless audio source.

PRODUCT ACCESSORIES LIST

1. 1-A AC Adapt r
   1-B Power Cord

2. HDMI Cable x1

3. USB Type C Cable
   (Note: only apply for Sport MGFU-S model)

4. 4-A Remote Control
   4-B Battery (AAAx2)

5. User’s Guide (with Warranty Card)

6. Tripod

7. Carrying bag

POWER ON/OFF

1. Connect the power cord to the DC input jack.

2. I nsert the plug into a power outlet.

3. MosicGO ® has an internal battery pack. Please fully charge the battery before using the projector.
   (*Note: Only the Sport MGFU-S model has a battery pack)

4. Press the Power On/Off Switch. The OK icon on the touch keypad will illuminate.

BT SPEAKER/PROJECTOR ON/OFF

1. Press the PJ button to turn the projector on and the status LED indicator will light up. To turn off the projector, press and hold the PJ button for over 1 second. After seeing the prompt message, short-press the PJ button again to confirm. The MosicGO® logo will show briefly before the device powers off. The status LED indicator light will be flashing as the projector powers down. When the projector is ON, short pressing the PJ button on the remote control will cycle through the following brightness modes: MAX, ECO, and MIN.
2. Press the Wireless Speaker button to activate this feature. Its blue LED lamp will flash when the Wireless Speaker is in pairing mode. Check “MosicGO®” on your device to connect to MosicGO® Wireless Speaker. When the device is connected successfully, the blue LED lamp will light persistently.To turn off the Wireless Speaker, press down and hold the BT button for over 1 second.When both the projector and Wireless Speaker are ON, short pressing the Wireless Speaker button on the remote control will switch the audio source between the projector and Wireless Speaker.

Note:
An audible tone sounds when the Wireless Speaker powers on/off, or when the projector connects/disconnects to a device.

Note:

• Press the 18 Wireless Speaker 19 button/PJ button to turn off the Wireless Speaker/projector before pressing the 7 power off switch.
• Avoid pressing the 7 power off switch directly when the projector/Wireless Speaker still on

BATTERY STATUS INDICATOR

LEDs indicate battery and charging status as the following table.

In battery mode, MosicGO® will be forced to power off if battery capacity is under 10% Suggest charging the battery immediately if the LED indicator is Red.

Note:
There is no battery in the Lite MGFU-L version. Power LED is green solid when the DC adapter is inserted.)

BATTERY FOR POWER SOURCE

• USB Type C power Delivery:
  Type C support PD function. Please refer specification section for details.
  Note:
  When projecting video connect, USB type C ports automatically switch to a lower (5V1A) power rail.

• USB Type A:
  Provide 5V/1A max power.

CONNECT INPUT SOURCE: HDMI or USB Type C Display Port

ADJUST PROJECTION IMAGE TILT

• The projector is equipped with four elevator feet for adjusting the projected image tilt.
• To adjust the tilt:
  Turn the elevator feet to adjust the projected image position to the desired tilt.

ADJUST THE PROJECTION IMAGE SIZE

A| B| C| D| E| ****

Note

---|---|---|---|---|---
Projector Front Edge Distance to Screen| Screen lower edge

to projector table

| Projector Screen diagonal| Projector Screen width| Projector Screen height
inch| inch| inch| inch| inch
3.82| 9.41| 60| 52.3| 29.4|
6.42| 10.75| 70| 61.0| 34.3|
9.17| 11.89| 80| 69.7| 39.2|
11.97| 13.35| 90| 78.4| 44.1| ****

*Note

14.53| 14.37| 100| 87.2| 49.0
21.38| 17.56| 125| 108.9| 61.3

Note:
The MosicGO® (Lite MGFU-L & Sport MGFU-S) portable UST (ultra-short throw) projectors are specifically designed for creating 60-80” imagery in a 16:9 aspect ratio.
Throwing larger (90”-125”) images will have corner distortion and is more recommended for videos than in still shot / training presentations .

Note:
The tolerance is around 5% .

EARPHONE

Earphone, 3.5mm Jack Pin assignment

• HPL: Left Channel Audio Signal
• HPR: Right Channel Audio Signal
• GND: Signal Ground

12V TRIGGER

12V Trigger Port, 3.5mm Jack Pin assignment

• 12V: 12V trigger signal for screen rolling up/down
• GND: Signal Ground

Note:
The Earphone output is not designed as a line out (AUX out) to connect to an amplifier/stereo or powered speaker. If you want to connect this type of device, we recommend purchasing a Ground Loop Noise Isolator to help eliminate the humming noise emitting from the devices.

Warning : Don’t plug in earphones to the 12V trigger port, which can cause damage to the earphone.

MCOOUNT THE PR OJ ECTOR

Screw a standard tripod into the screw hole on the projector.

1. Loosen 4 screws to remove the metal plate from MosicGO®.
2. Fasten screws (m4) to ceiling mount kits.

Note:
Tripod should support loading above 3Kg, and mounting screw spec is 1/4 ”

Note2

Note:
Please keep air vents open for heat ventilation. Otherwise, the projector will be turned off if it’s overheating.

OSD

• Contrast: adjust color contrast.
• Sharpness: adjust picture sharpness.
• Pattern Test: present a pattern picture to verify the focus and color situation of the display. Press “OK” will return to the current video port.
• Picture Test: circularly present red, green, blue, and white screens to verify picture color. Press “OK” will return to the current video port.
  Note:

1. Contrast and Sharpness can be configured only when the video signal is ready.
2. Reset to the default setting by selecting ‘Menu’->’Other’->’Reset

• Auto Power Off: Configure the time before power off if there is no signal to the projector.
• H / V Position: Adjust the display position
  Note:

1. H Position and V Position can be configured only when the video signal is ready.
2. Reset to the default setting by selecting ‘Menu’->’Other’->’ Reset’

Configure color properties.

Note:

1. All COLOR Menu can be configured only when the video signal is ready.
2. Some features might not be supported in the current model.
3. Reset to the default setting by selecting ‘Menu’->’Other’->’ Reset’

• Set other configurations.

• Aspect Ratio: configure the ratio of the display area.

• Projector Installation: according to your projector installation, configure the orientation of the display.

• Ultra vivid: enable/disable supporting vivid color.
  Note:

  1. Aspect Ratio and Ultra Vivid can be configured only when the video signal is ready
  2. Some features might not be supported in the current model.
  3. Reset to the default setting by selecting ‘Menu’->’Other’->’ Reset’

• 12V Trigger: Enable/disable the output of 12V Trigger Out.

• Keystone: adjust the rectangle shape of the display.

• Language: configure language

• Transparency: configure the transparency of OSD(on-screen display).

• S.P.M: enable/disable Smart Projector Mode. If enable, MosicGO® will automatically adjust brightness according to the current battery and power situation.

• Buzzer: enable/disable the “beep” alert sound.

• Rest: reset to default setting.
  Note:

  1. Brightness cyclic MAX/ECO/MIN will be disabled when S.P.M is ON.
  2. If Keystone is enabled, the projector will automatically adjust the image display within 2-3 seconds. Press the up/down key to adjust slightly also.
  3. Reset to the default setting by selecting ‘Menu’->’Other’->’ Reset’

• Present current video signal information.

SPECIFICATIONS

edge
Projection

Size

| 1.52-2.54 m ( ” – 100″)
Focus| Manual
Throw Ratio| 0. (80″@0.5m)
Keystone| Vertical keystone
Projection Modes| Front Table, Rear Table, Front Ceiling, Rear Ceiling
Standard Input| Up to       (1920 x 1080)
SDTV/EDTV/ HDTV| 480i, 480p, 576i, 576p, 720p, 1080p
Horizontal Frequency| 30.5 – 91.1kHz
Vertical Frequency| 50 – 85Hz
Operating Temperature| 0 – 40°C
Dimensions (WxHxD)| (back) / 127(front)mm
AC adapter| 100 – 240V, 50 – 60Hz
Power Input| 19V DC, 6.3A
Power Consumption| Less than 120W
Lamp| RGB LED
Lamp Life| 25,000 Hours
Speakers| 8W x 2 music power
Battery Capacity| 37200mAH (135 Watt-Hours)
Battery Life

(for MGFU-S model)

| Up to 3 hours play time in Eco mode.
Eco Mode: Lowest brightness and low volume.

Input/Output Ports

| Alt-DP (USB type C connector) x 1
HDMI 1.4 x 2
USB type A poewr charging port (5V1A) x 2
USB type C PD power source port x 2 (Note)
Earphone out
12V Trigger Out (0.1A output max.)
Wireless Speaker audio in x 1
Waterproof| IPX2
Security| Kensington Slot

Note:

• Power Delivery (PD):
  • maximum 5V/3A,9V/3A,15V/3A,20V/4.35A for port USB type-C port
  • maximum 5V/3A,9V/3A,15V/2A,20V/1.5A for port 3 USB type-C port

TROUBLESHOOTING

If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local retailer or service center.

No image appears on the screen

• Ensure the power cord is correctly and securely connected.
• Ensure the cable is fine.
• Make sure the projector is switched on.

The image is out of focus

• Make sure the projection distance is in the valid range (refer to page 10).
• Projecting test pattern (‘Menu’-> “Picture”, press ‘OK-> “Pattern Test press “OK)
• Adjust the focus ring, and make the line pattern on four corners and center clear. Exit “Pattern’by pressing “OK’again.

Image is too small or too large

• Move the projector closer to or further from the screen.

No sound

• During music playback, press the remote control.

During music playback, press/the remote control.
Use a hairdryer in a low heat setting to clear away dust, water, or other particles. To Prevent Damaging the Surface Coating, DO NOT Touch, Wipe or Clean the Lens. If the projection surface is heavily soiled, contact the manufacturer for further assistance.

Frequently asked questions

• https://www.eliteprojector.com/faqs.html.

Note:
When the projector’s temperature is too high, the projector automatically shuts down due to the built-in temperature protection. This is not a malfunction. Let the projector cool down before switching it on again.

Note:
MGFU-S/MGFU-L is splash resistant and was tested under controlled laboratory conditions with a rating of IPX2 under IEC standard 60529. Splash resistance is not permanent condition and resistance might decrease as a result of normal wear. Do not attempt to charge a wet MGFU-S/MGFU-L; Liquid damage is not covered under warranty. “To Prevent Damaging the Surface Coating, DO NOT Touch, Wipe or Clean the Lens.* Consult the manufacturer for special cleaning instructions.

Supported HDMI input video signal:

Supported HDMI input video signal:| Vertical Frequency (Hz)
---|---
Resolution| Horizontal Frequency (kHz)| 70.09
640 x 350| 31.468| 70.08
720 x 400| 31.469| 59.94
640 x 480| 31.469| 60.31
800 x 600| 37.879| 60.00
1024 x 768| 48.363| 60.053
1152 x 864| 54.348| 60.015
1360 x 768| 47.712| 60.020
1280 x 1024| 63.981| 60
1920 x 1080|  |
67.5

• If an invalid signal is an input into the projector, it will not be displayed properly on the screen or a message such as ‘not support’ will be displayed.
• To provide the best picture quality, 1920 x 1080 (1080p) resolution is recommended.

TROUBLESHOOTING

3 continuous beep sound
You may hear 3 continuous beep sounds accompanying the following icon on the screen

• Low battery: the projector is turned off immediately. Please plug in the power adapter to charge the battery. You can turn on the projector during charging.
• Battery fails: if the power adapter is plugged. You can turn on and use the projector. If you pull out the power adapter, the projector may be turned off without any warning. If the problem still occurs, please check with your vendor.
• Overheat: the projector is turned off immediately. Suggest letting the projector be off for a while before it is turned on again.
• Fan error: the projector is turned off immediately. If the problem still occurs, please check with your vendor.

Note:
The projector may be overheat and turned off immediately. Suggest letting the projector be off for a while before it is turned on again.

Dimension

QUICK SETUP FOR MODEL: OMS58H2

Actual Height and Distance May Vary

Warranty

13 Months Warranty Card

Elite Screens Visual & Sound Co., Ltd.

for more updated user manual:

Electronic file link
www.eliteprojector.com/MGFU/manual.

www.eliteprojector.com.
Printed in Taiwan
FBZZ-MG1Z002-06.

References

• EliteProjector® - MosicGO Outdoor Ultra Short Throw Projector - EliteProjector® MosicGO® Outdoor Ultra-Short Throw Projector
• Downloads - EliteProjector® - MosicGO Outdoor Ultra Short Throw Projector
• FAQs - EliteProjector® - MosicGO Outdoor Ultra Short Throw Projector

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>