HOIST RS-1203 Aviron Portland FItnes Instructions
- June 10, 2024
- HOIST
Table of Contents
- HOIST RS-1203 Aviron Portland FItnes
- Product Information
- Product Usage Instructions
- INSTRUCTIONS
- FRAME ASSEMBLY
- PRE-ASSEMBLY
- DECAL PLACEMENT
- DECAL REFERENCE
- ABBREVIATIONS
- BOLT SIZING CHART
- WASHER SIZING CHART
- MAINTENANCE SCHEDULE
- HOIST FITNESS SYSTEMS
- WEIGHT TRAINING TIPS
- WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HOIST RS-1203 Aviron Portland FItnes
Product Information
The RS-1203-A is a seated mid-row exercise machine designed to provide effective exercise motion for users. The machine comes with a ROC-IT weight cage that can be installed on either the left or right side of the machine to accommodate the user. The machine should be bolted to the exercise floor to prevent tipping, failure to do so may result in serious injury or death. The machine is designed with various parts and hardware that should be tightened properly during assembly to ensure correct operation.
Product Usage Instructions
- Before beginning assembly, read the instructions thoroughly and ensure that all parts have been included in your shipment.
- Use the various lists in the manual to identify all parts and their corresponding part numbers.
- Use only HOIST replacement parts when servicing the machine to avoid voiding the warranty and possible personal injury.
- Assemble the weight cage first by hand-tightening all hardware and ensuring the use of weight stack #2.
- Attach the cables and pulleys at the same time as frame assembly.
- Wrench-tighten all hardware after the frame assembly is complete.
- Loosen jam nut for fine tuning and adjust cable tension by threading bolt in/out before re-tightening jam nut.
- Bolt the machine to the exercise floor to prevent tipping and ensure correct operation during use.
- If you experience any problems during assembly or use, first recheck the instructions to locate any possible errors made during assembly. If you’re unable to correct the problem, call your authorized HOIST dealer for assistance. Have your serial number and manual available when calling for support.
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that all
parts have been included in your shipment. When ordering, use part number and
description from the lists. Use only HOIST replacement parts when servicing.
Failure to do so will void your warranty and could result in personal injury.
HOIST equipment is designed to provide the smoothest, most effective exercise
motion possible. After assembly, you should check all functions to ensure
correct operation. If you experience problems, first recheck the assembly
instructions to locate any possible errors made during assembly. If you are
unable to correct the problem, call your authorized HOIST dealer. Be sure to
have your serial number and this manual when calling. When all parts have been
accounted for, continue on.
TOOLS REQUIRED
Ratchet Wrench
1/2″, 9/16″ and 3/4″ Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
FRAME ASSEMBLY
ASSEMBLE WEIGHT CAGE FIRST
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY HAND TIGHTENED HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT HANDLE ASSEMBLY STEPS FOR OPPOSITE SIDES.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT FOOT REST ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT FOOT REST ASSEMBLY FOR OPPOSITE SIDE.
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
NOTE:
- WRENCH TIGHTEN HARDWARE.
STOP
WHEN FINISHED WITH THIS STEP PLEASE SEE ROC-IT WEIGHT
CAGE MANUAL FOR FINAL ASSEMBLY.
IMPORTANT
NOW THAT THE RS-1203-A IS COMPLETELY ASSEMBLED TAKE TIME TO ASSURE THAT YOUR UNIT IS ASSEMBLED SQUARE AND PERPENDICULAR. IF NOT IT WILL BE NECESSARY TO LOOSEN SOME FRAME HARDWARE TO RE-ALIGN THE FRAME AND RETIGHTEN BOLTS.
PRE-ASSEMBLY
DECAL PLACEMENT
NOTE:
- SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY.
DECAL REFERENCE
PART LIST CONTINUED
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO.| PART NUMBER| DESCRIPTION| QTY.
1| 026-01X3979| REAR LINK ASSEMBLY| 1
2| 026-01PL2124| FOOTPLATE, MOLDED| 2
3| 026-01X3793| PULL ARM ASSEMBLY| 1
4| 026-01X6561| BASE FRAME ASSEMBLY| 1
5| 026-01X3796| FRONT LINK ASSEMBLY| 1
6| 026-01X6559| USER SUPPORT FRAME ASSEMBLY| 1
7| 026-01X2469| GRIP ASSEMBLY| 2
8| 026-01X2581| CROSS MEMBER ASSEMBLY| 1
9| 026-01X2588| HAND GRIP| 2
10| 026-01X2604| CROSS BAR ASSEMBLY| 1
11| 026-01X2605| HANDLE BAR ASSEMBLY| 1
12| 026-01X6560| MID LINK ASSEMBLY| 1
13| 010-01C0409| CABLE ASSEMBLY ROC-IT 1203-A – 145 1/16″ LG.| 1
14| 018-0001003| CABLE PULLEY: Ø4.50″| 2
15| 019-0001001| PLUG BUMPER| 5
16| 022-01PD2056| SEAT PAD ASSEMBLY| 1
17| 026-01F0256| BACKING PLATE| 1
18| 026-01M1097| BEARING TRIM CAP| 2
19| 026-01M1103| THREADED CABLE ANCHOR Ø1.00″ O.D X 2.50″ LG.| 1
20| 026-01M2360| SHAFT – 25mm X 4.71″ LG.| 3
22| 026-01M2902| SHAFT – 1.181 X 4.7100 LG.| 2
23| 026-01M1041| SHAFT: .75″ O.D. X 5.8500″ LG.| 2
24| 026-01P2650| CABLE SHIELD| 1
25| 026-01P2653| ‘H’ PLATE| 1
26| 026-01PL2122| OVAL-SHAPED RUBBER FOOT| 2
27| 011-0701020| 3/8″-16UNC X 1.00″ BHCS (Ni)| 6
28| 011-0701049| 1/2″-13UNC X 1.50″ BHCS (Ni)| 2
29| 011-0701004| 5/16″-18UNC X 1.25″ BHCS (Ni)| 4
30| 011-0116145| 3/8″-16UNC X 1.75″ LOW HEAD SHCS (Ni)| 1
31| 011-0116148| 3/8″-16UNC X 2.50″ LOW HEAD SHCS (Ni)| 2
32| 011-0116116| 1/2″-13UNC X 3.25″ LOW HEAD SHCS (Ni)| 4
33| 011-0116119| 1/2″-13UNC X 4.00″ LOW HEAD SHCS (Ni)| 2
34| 011-0116127| 1/2″-13UNC X 6.00″ LOW HEAD SHCS (Ni)| 1
35| 012-0504005| 3/8″-16 UNC THIN NYLOCK NUT (Ni)| 7
PART LIST CONTINUED
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO.| PART NUMBER| DESCRIPTION| QTY.
36| 012-0504002| 1/2″-13 UNC THIN NYLOCK NUT (Ni)| 13
37| 013-1002006| 1/2″ X 27mm SAE FLAT WASHER (Ni)| 24
38| 013-1002010| 5/16″ SAE FLAT WASHER (Ni)| 4
39| 013-1002007| 3/8″ X 22mm FLAT WASHER (Ni)| 18
40| 014-0024004| 3/4″ I.D. THRUST WASHER| 4
41| 013-1006003| 3/8″ SPLIT LOCK WASHER (Ni)| 2
42| 014-0005001| BEARING: (SMALL) Ø1.37″ O.D. X Ø.75″ I.D. X .39″ LG| 2
43| 014-0012014| BEARING: FLANGELESS – 25mm I.D.| 6
44| 014-0012013| BEARING: BALL BEARING Ø2.44″ O.D. X Ø1.18″ I.D.| 4
45| 014-0012002| THRUST BEARING 3/4″ I.D.| 2
46| 014-0014002| 3/8-16 FLUSH MOUNT INSERT| 4
47| 021-0013305| PLACARD RS-1203 MID ROW| 1
48| 021-0003853| ROC-IT QR DECAL MID ROW| 1
49| 021-0003114| DECAL PINCH POINT 1.63″ X 3.25″ (HORIZONTAL)| 2
50| 021-0003093| DECAL MOVING PARTS 1.20″ X 2.38″ (HOR)| 1
51| 021-0003420| DECAL ROC-IT MID ROW HAND MOVEMENT| 1
53| ROC-IT WEIGHT CAGE – A2| ROC-IT WEIGHT CAGE| 1
54| 013-0903008| .755″ I.D. WAVE WASHER| 2
55| 026-01PL2351| PLASTIC SCUFF GUARD W/ RIVETS| 1
56| 026-01M1137| CABLE ANCHOR SHAFT Ø.38″O.D. X 3.0625″ LG.| 1
57| 026-01F0267| FLANGE| 1
58| 014-0101020| BUSHING: OILITE FLANGED Ø.63″ O.D. X Ø.38″ I.D. X .50″ LG.| 2
59| SERIAL # DECAL| DECAL HOIST SERIAL # 1.63″ X 2.63″| 1
60| 026-01PL2200| PINETREE PLUG| 1
61| 014-0012018| SNAP RING – 25mm EXTERNAL| 6
62| 014-0012019| SNAP RING – 30mm EXTERNAL| 4
63| 018-0002017| PULLEY 6.00″ OD| 1
64| 011-0401005| 3/8″-16UNC X 1.00″ BHCS (SS)| 4
65| 011-0716019| M16-2.00 x 150 LOW HEAD SHCS (Ni)| 1
66| 012-0504006| 5/16″-18UNC THIN NYLOCK NUT (Ni)| 2
67| 012-0504009| M16-2.0 THIN NYLOCK NUT (Ni)| 2
68| 013-1002013| M16-2.0 FLAT WASHER (Ni)| 4
69| 013-0402011| 3/8″ SPLIT LOCK WASHER (SS)| 4
70| 013-1010003| 5/16″ INTERNAL LOCK WASHER (Ni)| 4
PART LIST
NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED
ITEM NO.| PART NUMBER| DESCRIPTION| QTY.
72| 013-0402010| 3/8″ X 22mm FLAT WASHER (SS)| 4
73| 011-0716020| M16-2.00 x 160 LOW HEAD SHCS (Ni)| 1
75| 021-0003934| RS WEIGHT STACK DECAL #2| 1
76| 014-0005003| BEARING: 2 ROW BB – 25mm I.D.| 6
77| 026-01M0238| FLATHEAD CAP Ø2.00″ ALUM.| 6
78| 026-01M2987| PIVOT SHAFT| 3
79| 011-0702020| 3/8″-16UNC X 1.00″ FHCS (Ni) W/NYLON PATCH| 6
80| 011-0116126| 1/2″-13UNC X 5.75″ LOW HEAD SHCS (Ni)| 2
ABBREVIATIONS
BZ = Black Zinc
Ni = Nickel Plated
SS = Stainless Steel
WZ = White Zinc
HHB = Hex Head Bolt
FHCS = Flat Head Cap Screw
BHCS = Button Head Cap Screw
SHCS = Socket Head Cap Screw
Low Head SHCS = Low Head Socket Head Cap Screw
SHSS = Socket Head Shoulder Screw
BOLT SIZING CHART
WASHER SIZING CHART
MAINTENANCE SCHEDULE
Your equipment comes with a commercial maintenance decal.
For personal, in home use, please follow the home maintenance schedule listed
above.
Never use ammonia, acid-based, or petroleum-based solvents on any portion of
the machine as it may damage the finish.
HOIST FITNESS SYSTEMS
GENERAL MAINTENANCE INFORMATION
Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack Pins:
- Check all pieces for signs of visible wear or damage.
- Check springs in snap hooks and pull-pins for proper tension and alignment.
- If the spring sticks or has lost its rigidity, replace it immediately.
Upholstery:
- To ensure prolonged upholstery life and proper hygiene, all upholstered pads should be wiped down with a damp cloth after every workout.
- Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying. Avoid using any abrasive cleaners or cleaners not intended for use on vinyl.
- Replace ripped or warn upholstery immediately.
- Keep sharp or pointed objects clear of all upholstery.
Decals:
*Inspect and familiarize yourself with any safety warnings or other user information posted on each decal.
Nuts and Bolts:
- Inspect all nuts and bolts for any loosening and tighten if needed.
- Go through a re-tightening sequence periodically to ensure that all hardware is tensioned proper.
Anti-Skid Surfaces:
*These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery.
Belts and Cables:
- Hoist uses only high quality belt, and mil-spec cables.
- Visually inspect the belts and cables for fraying, cracking, peeling or discoloration.
- While the machine is not in use, carefully run your fingers along the belt or cable to feel for thinning or bulging areas.
- Replace belts and cables immediately at the first signs of damage or wear. Do not use equipment until belts or cables have been replaced.
Belt and Cable Tension:
- Referring to the Owners Manual, when belts or cables are used check all bolts attachments to be sure they are properly attached.
- Check slack in cables and re-adjust cable tension if needed.
Seat Sleeves, Guide Rods:
- Wipe down adjusting tubes with a dust free rag before applying lubricant.
- Lubricate seat sleeves and Guide Rods with a Silicon or Teflon based lubricant spray.
Linear Bearings:
Referring to the Owners Manual carefully disassemble the bearing from its
housing and place a finger full of light grease (lithium, super lube, etc.)
into the inside of the bearing. Using your finger, press the grease into the
ball-bearings and their tracks. repeat until the ball-bearing tracks are full
of grease. Insert the shaft back into the bearing and wipe off excess grease.
WEIGHT TRAINING TIPS
Use this manual to guide you through the basic exercises you can perform on
your RS-1203-A HOIST® Fitness System. To gain maximum results and avoid
possible injury, consult a fitness professional to develop your complete
exercise program.
Always consult your physician before starting any exercise program.
To be successful in your exercise program, it is important to develop an
understanding of the basic principles of strength training. Now that you have
your RS-1203-A HOIST® Fitness System, it is only natural that you want to get
started immediately. First, determine a set of realistic goals and objectives
for yourself. By deciding on an exercise plan that is right for you prior to
starting, you will contribute significantly to your success.
Warm up properly before engaging in weight resistance training. Stretching,
yoga, jogging, calisthenics or other cardiovascular exercise can help prepare
your body for the heavier workload of lifting weights.
Learn how to perform the exercise correctly before using heavy weight. Correct
form is important to avoid injury and to ensure that you work the proper
muscle groups.
Know your limitations. If you are new to weight training or are embarking on
an exercise regimen after a long layoff, start slowly and build foundational
strength over a longer period of time.
Pay attention to your breathing. Exhale when you exert is a general rule of
thumb. Never hold your breath.
WEIGHT TRAINING EXERCISE LOG
S = Sets R = Repetition per set W = Weight used
WARRANTY
HOIST FITNESS SYSTEMS LIMITED LIFETIME WARRANTY
Hoist Fitness Systems warrants this product to the original purchaser to be
free from defects in workmanship and/or materials under normal use or service.
If at any time a component part is defective, Hoist Fitness Systems shall
repair or replace it (at Hoist Fitness Systems option) within a reasonable
period of time. This warranty does not cover costs of removal, transportation
or reinstallation. This warranty shall not apply if the defect was caused by
misuse, neglect or normal wear and tear.
WARRANTY CLAIMS. All claims require: Model number, Serial number, Date of
installation, and any information supporting the existence of the alleged
defect.
To complete Warranty Registration visit:
www.HOISTFITNESS.com
and click on the Warranty Registration link
Starting from the original date of purchase, normal wear and tear shall be
considered as the following:
COMMERCIAL USE: All malfunctions of upholstery, grips, and coatings that
occur up to one year; all malfunctions of belts, or cables up to one year; all
malfunctions of pulleys, bearings, or bushings that occur up to three years.
The frame and body components are warranted for ten years, with structural
moving parts warranted for five years.
LIGHT COMMERCIAL USE: All malfunctions of upholstery, grips, and coatings
that occur up to one year; all malfunctions of belts, or cables up to one
year; all malfunctions of pulleys, bearings, or bushings that occur up to
three years. The frame and body components are warranted for ten years, with
structural moving parts warranted for five years.
HOME USE: All malfunctions of grips, paint, and chrome that occur up to
ten years; all malfunctions of electronic components, belts, cables, or
upholstery that occur up to ten years; all malfunctions of pulleys, bearings,
or bushings that occur up to ten years. The frame and all welded components
are warranted for the life of the product.
PLEASE NOTE THAT NOT ALL HOIST PRODUCTS ARE MADE FOR COMMERCIAL USE.
Refer to the instructions page of your owners manual or consult with you
fitness product dealer to establish if a product is made for commercial use or
not. Using a non-commercial product in a commercial setting can result in
serious injury or death! Hoist Fitness Systems sole responsibility shall be to
repair or replace the component within the terms stated above. Hoist Fitness
Systems shall not be liable for any loss or damage of any kind including any
incidental or consequential damages resulting, directly or indirectly from any
warranty expressed or implied or any other failure of this product.
LIGHT COMMERCIAL USE: Our Light Commercial warranty applies to facilities
that DO NOT charge monthly membership dues and where the equipment would be
used by no more than 50 people per day. Examples of Light Commercial
facilities include hotels, apartment complexes, personal training studios,
fire stations, police stations, etc., that meet the criteria stated above.
WHAT IS NOT COVERED BY THIS WARRANTY: Hoist’s sole obligation under this
warranty is limited to either repair or replacement of parts, subject to the
additions below. This warranty neither assumes nor authorizes any person to
assume obligations other than expressly covered by this warranty.
NO CONSEQUENTIAL DAMAGES: Hoist is not responsible for economic loss;
profit loss; or special, indirect, or consequential damages.
WARRANTY IS NOT TRANSFERABLE: This warranty is not assignable and applies
only in favor of the original purchaser/user to whom delivered. Any such
assignment or transfer shall void the warranties herein made and shall void
all warranties, expressed, implied or statutory, except the one (1) and five
(5) year warranties described above. These warranties are exclusive and in
lieu of all other warranties, including implied warranty and merchantability
or fitness for a particular purpose. There are no warranties which extend
beyond the description on the face hereof.
TRANSPORTATION COSTS: Hoist will accept parts covered under this warranty
freight collect, provided that shipment has received prior approval. Hoist is
not responsible for any other transportation costs, but will ship freight
collect parts either repaired or replaced under these warranties.
Hoist Fitness Systems
11900 Community Rd.
Poway, CA. 92064
(800)548-5438
PLEASE KEEP THIS FOR YOUR RECORDS
Customer Service
Fax 858-578-9558
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>