SAFETY HOIST EH-250 Electric Material Hoist Instruction Manual

August 10, 2024
SAFETY HOIST

EH-250 Electric Material Hoist

“`html

Product Information

Specifications:

  • Model: EH-250 Electric Material Hoist
  • Version: 0124
  • Type: Platform Material Hoist

Product Usage Instructions

General Recommendations and Advice:

  1. Never operate the hoist in wet weather conditions.

  2. Do not use the hoist to transport a person from one elevation
    to another.

  3. Avoid using the hoist track as a ladder to prevent injury.

  4. Check the condition of the electric hoist before connecting the
    pendant and power cords.

  5. Inspect winch drum and cable assembly for damage or
    misalignment. Use the pendant to correct any crossovers in the
    cable.

  6. Ensure the pendant and power cables are in good condition with
    no cuts or tears.

  7. Test the brake system with a load of about 70 to 100 lbs before
    lifting heavier loads.

General Safety Instructions:

The safety instructions and warnings in this manual must be read
carefully before assembling or operating the hoist to prevent
injury or damage.

A. Unpacking Your Hoist:

Inspect for any damage during transit. Do not use if any part is
damaged. Return damaged parts for replacement.

B. Safety Labels:

Observe and follow all safety labels attached to the hoist
parts.

C. Proper Parts:

Use only approved attachments and accessories for safety. Using
substitute parts will void the warranty.

D. Safety Check:

Check all assembled parts for tightness and fit before use.
Recheck for bolt tightness before each use and every 4 hours of
operation.

FAQ (Frequently Asked Questions)

Q: Can the hoist be operated in wet weather conditions?

A: No, the hoist should never be operated in wet weather
conditions for safety reasons.

Q: What weight should be used to test the brake system?

A: Use one bundle of shingles (or about 70 to 100 lbs.) to test
the brake system before lifting heavier loads.

Q: What should I do if I find damaged parts when

unpacking?

A: Do not assemble or use the hoist if any part is damaged.
Return the damaged part for replacement.

“`

Operator’s Manual
EH-250 Electric Material Hoist
info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com
Version 0124

Operator’s Manual

EH-250 Platform Material Hoist

TABLE OF CONTENTS

GENERAL RECOMMENDATIONS & ADVICE ………………………………………………………………………………… 1 GENERAL SAFETY INSTRUCTIONS ………………………………………………………………………………………… 2-3 SAFE OPERATION …………………………………………………………………………………………………………………….. 3 LIST OF COMPONENTS …………………………………………………………………………………………………………….. 5 HOIST HEIGHT CHART ……………………………………………………………………………………………………………… 6 HOW TO ASSEMBLE YOUR HOIST……………………………………………………………………………………………7-9 HOW TO OPERATE YOUR HOIST…………………………………………………………………………………………. 10-11 PARTS LIST……………………………………………………………………………………………………………………….. 12-16 MOTOR RECOMMENDATIONS…………………………………………………………………………………………………. 17 SAFETY HOIST COMPANY – LIMITED WARRANTY…………………………………………………………………….. 18

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com

Operator’s Manual

EH-250 Platform Material Hoist

GENERAL RECOMMENDATIONS AND ADVICE

EVERY TIME A SAFETY HOIST IS SET UP FOR OPERATION YOU MUST:

1. NEVER OPERATE HOIST IN WET WEATHER CONDITIONS!!!

2. THIS HOIST SHOULD NEVER BE USED TO TRANSPORT A PERSON FROM ONE ELEVATION TO ANOTHER!!

3. REMEMBER THAT THE HOIST TRACK IS NOT A LADDER! IF USED AS A LADDER, INJURY MAY OCCUR.
4. Check condition of the electric hoist before connecting the pendant and the power cords.
5. Inspect winch drum and cable assembly for obvious damage or misalignment. Inspect winch drum to make sure that cable is wound smoothly with no crossovers. If there are any, use the pendant to run the hoist in reverse and pull off enough cable to eliminate the crossovers. Then, with a leather glove, carefully use the pendant to wind the cable back onto the drum to prevent cable kinking.
6. Inspect the pendant and power cables to make sure they are in good condition with no cuts or tears. Make sure no oil, mud, etc., has gotten onto the connector assemblies, which will cause the hoist to malfunction.
7. Test the brake system. Put one bundle of shingles (or about 70 to 100 lbs.) on the platform. Only lift it two or three feet, and stop it, to make sure the brake system is working properly, and then lower the load. Once you are certain the brake system will hold, raise the load you are trying to lift up a few feet. Stop raising the load and wait a minute to make sure the load does not slip. This will verify that the brake system is working properly for the full load weight.

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 1

Operator’s Manual

EH-250 Platform Material Hoist

GENERAL SAFETY INSTRUCTIONS
The safety instructions and warnings in this section and throughout this manual must be read carefully before assembling or operating the hoist. These safety instructions and warnings are not substitutes for routine accident prevention measures, which must also be implemented to eliminate potential risks and hazards. Failure to obey these safety warnings may result in injury
to you or others, or damage to the hoist or other property.
A. UNPACKING YOUR HOIST
– When unpacking, carefully inspect for any damage that may have occurred during transit. DO NOT ASSEMBLE OR USE THE HOIST IF ANY PART OR PARTS ARE DAMAGED!! Return the damaged part or parts to place of purchase for replacement. Compare received parts to list of components on page 5. If they are not all there, you should contact who you bought the hoist from, or call 610-941-4333.
B. SAFETY LABELS
– Observe all safety labels and instructions attached to the various parts of the hoist.
C. PROPER PARTS
– For your safety, use only attachments and accessories approved by the manufacturer for use with the hoist. Using substitute parts will void the warranty.
D. SAFETY CHECK
– Check assembled parts (splice plates, bolts, pulleys, hoist cable, etc.) for proper tightness and fit before using the hoist, and during frequent periods of use, be certain the equipment is in safe working condition. Before each use, recheck for bolt tightness, and also recheck every 4 hours of operation.
E. TRANSPORTING
– To avoid damage, handle hoist component parts with care when transporting. Secure hoist to truck bed with cord rope or bungee cord. Damaged parts MAY make hoist not SAFE to operate. NOTE: Transporting uncovered hoist’s in the rain may cause damage to the electric motor. Cover electrical components with a plastic sheet and inspect prior to use. See page 7 – How To Assemble Your Hoist.
F. BRACING YOUR HOIST
– Never place or operate the hoist on a slippery surface and make certain the base section is properly leveled and secured at the base to prevent slippage or unexpected movement. Make sure the hoist is braced against a building or solid surface at the correct angle as described herein.

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 2

Operator’s Manual

EH-250 Platform Material Hoist

GENERAL SAFETY INSTRUCTIONS Continued
The safety instructions and warnings in this section and throughout this manual must be read carefully before assembling or operating the hoist. These safety instructions and warnings are not substitutes for routine accident prevention measures, which must also be implemented to eliminate potential risks and hazards. Failure to obey these safety warnings may result in injury
to you or others, or damage to the hoist or other property.
G. HOUSEKEEPING
– Clear the area around the base of the hoist to avoid slipping, tripping, or falling against the hoist. Place the cords in a way that they will NOT be a tripping hazard.
H. SECURING YOUR HOIST
– Secure track to the roof with a rope. Tie the rope to a rung or the peak and then secure other end of rope to the building. Do not tie to the rail because the rope will interfere with the travel of the carriage.

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 3

Operator’s Manual

EH-250 Platform Material Hoist

SAFE OPERATION

HAZARD! – DO NOT PLACE OR USE THIS MATERIAL HOIST IN AN AREA WHERE IT COULD COME IN CONTACT WITH OVERHEAD WIRES OR ELECTRICAL WIRING CIRCUITS OR ANY OTHER HAZARDOUS OBSTRUCTION.

NEVER OPERATE HOIST IN
WET WEATHER CONDITIONS!!!
A. PROPER INSTRUCTIONS
– DO NOT ALLOW ANYONE TO OPERATE THE HOIST WHO HAS NOT BEEN PROPERLY AND THOROUGHLY TRAINED IN ITS OPERATION AND USE. BEFORE OPERATING, THE INSTRUCTIONAL YOUTUBE VIDEO ON PAGE 11 SHOULD BE VIEWED, OR YOU CAN FIND THE INSTRUCTIONAL VIDEO ON OUR WEBSITE — www.safetyhoistcompany.com
B. WARNING:
– USE THE HOIST FOR LIFTING MATERIALS ONLY. THE HOIST SHOULD NEVER BE USED TO TRANSPORT A PERSON FROM ONE ELEVATION TO ANOTHER!!!!
C. MAXIMUM CAPACITY
– THE MAXIMUM CAPACITY OF THE HOIST IS 250 POUNDS. DO NOT OVERLOAD!!
D. WARNING
– Keep hands, feet, other body parts and clothing away from the track and moving or rotating parts of the hoist when operating the hoist.
E. MOLTEN SUBSTANCES
– Do NOT use the hoist to lift buckets of hot asphalt or any other hot or liquid substance, unless contents are in a closed and sealed container.
F. SUPERVISION
– ALWAYS unplug the electric hoist from the power supply when you leave the vicinity of the hoist.
G. CLEANING YOUR POWER UNIT
– If you need to clean your power unit, NEVER use water. Use a damp cloth and wipe unit clean.

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 4

Operator’s Manual

EH-250 Platform Material Hoist

LIST OF COMPONENTS

1. ONE (1) – Power Unit (hoist bolted on base) (includes a storage compartment) 2. ONE (1) – Power cord with screw connection 3. ONE (1) – Pendant with screw connection 4. ONE (1) – Carriage with 1/2″ bolt, washers and lock nut (bolt assembled on carriage) & flap 5. ONE (1) – Peak assembly 6. ONE (1) – 4 ft. track section with splice plates attached 7. ONE (1) – 8 ft. base track section with feet attached 8. TWO (2) – 8 ft. track sections with splice plates attached 9. TWO (2) – Carriage stops and hardware 10. ONE (1) – Hardware bag and operating manual
Hardware bag includes: – FOUR (4) – 3/8″ X 4/4″ Carriage bolts and keep nuts – FOUR (4) – 3 8/16″ X 1″ Button head and lock nut

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 5

Operator’s Manual

EH-250 Platform Material Hoist

HOIST HEIGHT CHART

HEIGHT “A” TO BEARING POINT MAXIMUM HORIZONTAL DISTANCE “B” HOIST LENGTH “C”

10 FT.

2 FT. 6 IN.

12 FT.

14 FT.

3 FT. 6 IN.

16 FT.

18 FT.

4 FT. 6 IN.

20 FT.

22 FT.

5 FT. 6 IN.

24 FT.

26 FT.

6 FT. 6 IN.

28 FT.

30 FT.

7 FT. 6 IN.

32 FT.

34 FT.

8 FT. 6 IN.

36 FT.

38 FT.

9 FT. 6 IN.

40 FT.

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 6

Operator’s Manual
HOW TO ASSEMBLE YOUR HOIST
1. Unpack ALL parts of the hoist and lay them flat on the ground.
– See page 5 for a list of included parts and materials. If any parts are missing, call
610-941-4333.
2. Lay the base track section on the ground with the rung short-side facing down.
– NOTE: That the rungs are not centered on the rail. SEE FIGURE 1.
3. Attach carriage stops at this time by inserting into the 2nd rung from the bottom & fastening with the hardware on the backside.
– NOTE: There are right and left handed carriage stops.
4. Track sections are attached using the splice plates on the OUTSIDE of the track section.
– Attach them with 3/8″ x 3/4″ carriage bolts and lock nuts that are attached to the splice plates. SEE FIGURE 3.
5. Slide the carriage onto the track section from the TOP of the track (side opposite of feet).
– Do this with the flat surface of the carriage facing away from the base section. SEE FIGURE 4.A and FIGURE 4.B.

EH-250 Platform Material Hoist
FIGURE 2
FIGURE 3
A. BB. .

FIGURE 4.A and FIGURE 4.B FIGURE 1 info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com
7

Operator’s Manual

EH-250 Platform Material Hoist

HOW TO ASSEMBLE YOUR HOIST Continued

6. Slide the carriage along the track to the base section so that the bumpers rest on the carriage stops. Make sure the carriage slides smoothly on the track.
– If not, remove the carriage and reinstall, making sure carriage wheels roll on track flanges.
7. Slide the peak assembly (VH-B) onto the end of the track.
– Secure it with two (2) 3/8″ x 3/4″ carriage bolts and lock nuts that are supplied in the hardware bag. The square holes are off-set, the side with the yellow sticker should be facing up. SEE FIGURE 5.
8. Turn the hoist track w/ the carriage assembly attached on its side.
9. Remove power cord and pendant cord from the base storage compartment and attach them to the power unit with quick connect fittings.
– Attach strain relief hooks on cords to eyelits on hoist. SEE FIGURE 6.
10. Plug the power unit into a 110v 15-amp GFCI electrical supply.
Ground-Fault Circuit Interrupter
11. Unwind enough cable from the electric winch to go through pulley at the peak and back down the other side of the track to the carriage by pressing the down button on the pendant.
– SEE FIGURE 7.

FIGURE 5 Eyelits
Quick Connect Fittings FIGURE 6

FIGURE 7

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 8

Operator’s Manual

EH-250 Platform Material Hoist

HOW TO ASSEMBLE YOUR HOIST Continued

12. Attach the thimble on the cable to the back of the carriage using the 1/2-13 x 1.5 bolt washer thimble washer nut that is attached to the carriage.

– SEE FIGURE 8.

13. You are now ready to lift the hoist into place.

– WARNING: When setting up your hoist please take note of all overhead obstructions and/or electrical wires. Select a location that is free of traffic and
pedestrians.

FIGURE 8

14. Lay the assembled hoist alongside the wall where the hoist is to be used.

15. Place hoist against the building at the correct angle.

– See chart on page 6 to determine the correct angle of incline.

16. Attach lifting handle to the power pack w/ hardware included in hardware bag and wheel over to track section.

– SEE FIGURE 9.
17. Attach power pack to the 4th rung up from the bottom of the track and pin it to the 3rd rung up from the bottom of the track.

FIGURE 9

– SEE FIGURE 10.

18. Using the pendant, press the UP button to take the slack out of the cable.

19. You are now ready to operate the hoist.

pin

4th rung 3rd rung

FIGURE 10
info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 9

Operator’s Manual

EH-250 Platform Material Hoist

HOW TO OPERATE YOUR HOIST
THE OPERATOR OF THE HOIST MUST WEAR ALL THE NECESSARY PROTECTIVE GEAR WHICH SHOULD INCLUDE FOOT, HAND, EYE AND HEAD PROTECTION. KEEP HANDS AWAY FROM ALL MOVING PARTS AT ALL TIMES. SEE PAGE 2 FOR GENERAL SAFETY INSTRUCTIONS.

1. The operator should run a TRIAL RUN at this time by pressing the UP button on the pendant to raise the carriage. To bring carriage back down, press the DOWN button.
– Test should be done while the carriage assembly is loaded with 70 to 100 lbs. and should be run in accordance with these instructions to check for proper operation.
SEE FIGURE 11 & 12.
2. During the TRIAL RUN, be sure to inspect the winch drum assembly.
– Cable on winch drum must be smooth and in neat coils with no cable crossing. It should also be tight on the winch drum. If cable has crossovers or is loose, using the pendant, run the winch in reverse and pull off enough cable to fix crossovers or tighten loose cable. Rewind cable on winch drum neatly and tightly, with coils laying side by side.
3. Run one last TRIAL w/ a full load. Make sure the cable is tight and is properly attached to the carriage, press the UP button on the pendant.
– Do this 2 or 3 times.
4. If at any time the brake does NOT hold the carriage in place, call 610-941-4333.
5. DO NOT EXCEED THE HOIST WEIGHT LIMIT! THE WEIGHT CAPACITY OF THIS HOIST IS 250 LBS!!!

FIGURE 11 FIGURE 12

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 10

Operator’s Manual

EH-250 Platform Material Hoist

HOW TO OPERATE YOUR HOIST Continued

6. Press the UP (U) button on the pendant to start the winch and launch carriage into its upwards travel.
– The button must be pressed the entire time it takes to reach the unload position at the peak. When the carriage unloading flap rotates into the unload position, release the UP button to stop the winch. SEE FIGURE 13.
7. To bring carriage back down, simply press the DOWN (D) button on the pendant continuously until the carriage reaches the bottom.
8. If you choose to use the hoist to lower material to the ground, load material onto the carriage & hold the DOWN (D) button continuously until the carriage reaches the bottom.
– Make sure material is secure before descent.

FIGURE 13

9. After job is complete, disconnect the pendant and the power cords and store them in the storage compartment provided on the power unit.
– This is also a convenient place to store your
manual. SEE FIGURE 14.

FIGURE 14
We recommend that you view the instructional videos on our YouTube page for your Safety HoistTM model.

@Safety Hoist Company

Scan the QR Code to go directly to our YouTube channel!

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 11

Operator’s Manual

EH-250 Platform Material Hoist

BASE ASSEMBLY – NG-D-E100

ITEM NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

PART NUMBER NG-D-E101 HD-D403
.625 CAP NUT NG-D-E106
ELECTRIC HOIST NG-D-E121 NG-D-E102 NG-D-E125
.375-16 X 6.0 LG HHCS .375-16 X 1.0 LG BHCS
.375-16 LN 0.5-13 1.0 LG HHCS
0.5-13 LN .375-16 X .75 LG HHCS
EH-D136 LABEL-WARNING
.375 FW POP RIVET 0.125 X 0.187 LG

DESCRIPTION BASE WELDMENT
WHEEL .625 CAP NUT BRACKET, HOIST ELECTRIC HOIST BRACKET, HOIST SUPPORT
HANDLE ANCHOR PIN LANYARD 3/8-16 X 6.0 LG HHCS 3/8-16 X 1.0 LG BHCS
3/8-16 LOCKNUT 1/2-13 X 1.0 LG HHCS
1/2-13 LOCKNUT 3/8-16 X .75 LG HHCS
SERIAL NO. PLATE WARNING LABEL 3/8 FLAT WASHER POP RIVET 0.125 X 0.3125 LG

QTY. 1 2 2 2 1 1 1 1 1 4 8 4 4 3 1 1 1 4

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 12

Operator’s Manual

EH-250 Platform Material Hoist

CARRIAGE ASSEMBLY COMPLETE – VH-C

ITEM NO 1 2 3 4 5 6 7 8 9 10 11 12

PART NUMBER MH8
VH-C032 CH C CARRIAGE ANGLE
MH11 .375-16 X .75 LG HHCS
MH6A-RH MH6A-LH .375-16 LN
MH35 .3125-18 LN LABEL WARNING POP RIVET 0.125 X 0.187 LG

DESCRIPTION

QTY

CARRIAGE WELDMENT

1

FLAP ASSEMBLY

1

ANGLE, WHEEL SUPPORT

2

CARRIAGE WHEEL ASSY

4

3/8-16 X .75 LG HHCS

4

PLYWOOD CARRIER, RH

1

PLYWOOD CARRIER, LH

1

3/8-16 LOCKNUT

2

CARRIAGE BUMPER

2

5/16-18 LN

2

WARNING LABEL

1

POP RIVET 0.125 X 0.3125 LG

2

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 13

Operator’s Manual

EH-250 Platform Material Hoist

CARRIAGE FLAP ASSEMBLY – VH-C032

ITEM NO

PART NUMBER

DESCRIPTION

QTY

1

VH-C032-WELD

VH-C FLAP WELDMENT

1

2

.25-20 X 2.0 LG HHCS

1/4-20 X 2.0 LG HHCS

4

3

.25-20 NUT

1/4-20 NUT

12

4

SKATE

CARRIAGE SKATE WHEEL

4

5

.25-20 LN

1/4-20 LOCKNUT

4

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 14

Operator’s Manual

EH-250 Platform Material Hoist

PEAK ASSEMBLY – VH-B

ITEM NO

PART NUMBER

DESCRIPTION

QTY

1

VH-B010-WELD

VH PEAK WELDMENT

1

2

HD-B012

PULLEY

1

3

0.5-13 X 2.0 LG HHCS 1/2-13 X 2.0 LG HHCS

1

4

0.5-13 LN

1/2-13 LOCKNUT

1

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 15

Operator’s Manual

EH-250 Platform Material Hoist

EH-250 CAPACITY MATERIAL HOIST & ACCESSORIES
PART # DESCRIPTION

EH-250 MH8GH MH9SB CH-RAMP SB-ASSY
CH-A002

Material hoist, 28′ complete Gravel hopper Support brace Unloading ramp Flat Panel/Solar Panel Cradle
8′ Track section w/ splice plates (17.25″ x 3.0″ x 96″)

EH-250 MATERIAL HOIST AVAILABLE PARTS LIST

PART #

DESCRIPTION

EH-A001 CH-A002 CH-A003 CH-A007 VH-B VH-C
VH-C032-ASSY CH-C11PK CH-C35PK NG-D-E-100-PK HD-D403-PK NG-D-E-121-PK NG-D-E106-PK HD-D434-PK E-HOIST MH9SB CH-RAMP SB-ASSY

8 ft. Base track section 8′ Track section w/ splice plates (17.25″ x 3.0″ x 96″) 4′ Track section w/ splice plates (17.25″ x 3.0″ x 48″ long) Splice plates (2) w/ nuts & bolts Peak assembly Carriage assembly complete
Carriage flap w/ skate wheels Carriage wheel nut/bolt set (2 per pack) Carriage bumpers (2 per pack) Power weldment Wheels Top bracket Anchor Handle Motor Support brace Unloading ramp Flat Panel/Solar Panel Cradle

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 16

Operator’s Manual

EH-250 Platform Material Hoist

MOTOR RECOMMENDATIONS

SEE SEPARATE OPERATION MANUAL – ELECTRIC WIRE ROPE HOIST –
ACCOMPANYING THIS MANUAL.

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 17

Operator’s Manual

EH-250 Platform Material Hoist

SAFETY HOIST COMPANY – LIMITED WARRANTY

REPLACES ALL DATED OR UNDATED LIMITED WARRANTIES DATED BEFORE JUNE 25, 2017.
Safety Hoist Company will, at its option, repair or replace any part or parts of the Safety Hoist material hoist that are defective in material or workmanship, with the exclusion of the motor/engine, which maintain a separate warranty provided by the manufacturer of the motor/engine. The terms of the warranty of the motor/engine are provided on the previous page.
The limited warranty on all parts except the motor/engine is in effect for 1 year from the date of purchase.
Safety Hoist Company reserves the right to inspect the equipment for misuse, abuse, or failure to maintain the equipment properly.
Safety Hoist Company will make reasonable efforts to repair or replace defective equipment in a timely manner, but assumes no liability or expenses incurred for the time lost as a result of the repair or replacement.
The defective unit or parts should be returned to the dealer where the unit was purchased, or contact Safety Hoist Company at 610-941-4333.
There is no other express warranty implied. Warranties including those of merchantability and fitness for a particular purpose are limited to one year from purpose or to the extent permitted by law. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. This is the exclusive remedy and liability for incidental and consequential damages under any and all warranties are excluded to the extent permitted by law. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Safety Hoist Company shall be relieved of its performance of the duties under this warranty if any damage has been caused to the product as a result of misuse, abuse, failure to maintain the equipment or Act of God.

info@safetyhoistcompany.com · 610-941-4333 · www.safetyhoistcompany.com 18

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals