Honglink Wireless Solutions 2021IG830 LTE USB Modem User Guide
- June 4, 2024
- Honglink Wireless Solutions
Table of Contents
- Honglink Wireless Solutions 2021IG830 LTE USB Modem
- Introduction
- Installation
- Status Indicator Descriptions
- Using Software
- Specifications
- Disposal and Recycling Information
- EU Regulatory Compliance
- UK Regulatory Compliance
- FCC
- IC Radiation Exposure Statement
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Honglink Wireless Solutions 2021IG830 LTE USB Modem
Introduction
Supporting various network standards and operating bands, the LTE USB Modem can have access to the internet and transmit data between devices through the mobile communication link when using with a nano-SIM card.
- SIM Card Slot Cover
- SIM Card Slot
- Antenna Ports Cover
- Antenna Ports
- Status Indicator
- USB-C Port
Installation
Installing the SIM Card
As shown in Figure A, open the SIM card slot cover on the LTE USB Modem, instert the nano-SIM card into the slot in the direction in the figure, and close the cover.
To remove the SIM card, open the cover and press the SIM card to release it.
Connecting to a Device
The LTE USB Modem can connect to a computer or other specific devices. Connect
the USB-C port on the LTE USB Modem to the corresponding port on a device
using an appropriate cable according to the type of the port.
Status Indicator Descriptions
The LTE USB Modem will power on automatically when the device it connected to is powered on. The status indicator indicates the current working status. Refer to the table below for details.
| Indicator Status | Description |
|---|---|
| Solid green | Strong 4G signal. |
| Blinks green | Weak 4G signal. |
| Solid Blue | Strong 3G signal. |
| Blinks blue | Weak 3G signal. |
| Solid red | No SIM card detected. Make sure to insert a SIM card in good |
condition
correctly.
Blinks red| SIM card inserted, but no network signal. Check the related service of the
SIM card and the network signal nearby.
Blinks green and
blue alternatively
| Firmware updating.
Using Software
Connect the modem to a computer to configure APN settings, select network connection mode, update firmware, and reset the modem in the dedicated software for the modem.
- Visit the official DJI website (https://www.dji.com ) and download the software in your computer. The software supports Windows 7 or later.
- Connect the USB-C port on the modem to the computer using a USB-C cable. The status indicator lights up indicating connection is established.
- Run the software. Go to each page in the software for corresponding configuration.
Specifications
| Technical Standards | TDD-LTE CAT4/FDD-LTE CAT4/WCDMA HSPA+ |
|---|---|
| Operating Frequency Bands | TDD-LTE: B34/38/39/40/41 (194M) |
FDD-LTE: B1/B2/B3/B4/B5/B7/B8/B12/B13/B18/B19/B20 B25/B26/B28/B66/B71
WCDMA: B1/B2/B4/B5/B6/B8/B19
Max Output Power| TDD-LTE: 25 dBm
FDD-LTE: 25 dBm
WCDMA: 25 dBm
Interface| USB-C port
Nano-SIM card slot TS-5 antenna ports
Antennas| Dual antennas
Dimensions| 52.4×23.0×8.0 mm
Weight| Approx. 14 g
Operating
Voltage/Current
| 5 V, 1 A
Operating Temperature| -10° to 40° C (14° to 104° F)
Storage Temperature| -20° to 70° C (-4° to 158° F)
Disposal and Recycling Information
The crossed-out wheeled bin symbol on your product reminds you that all electrical and electronic equipment must be taken to separate waste collection points at the end of their lifecycle. It is the responsibility of the user to dispose of the equipment using a designated collection point or service for separate recycling of waste electrical and electronic equipment (WEEE) according to local laws. Proper collection and recycling of your equipment helps ensure electrical and electronic equipment waste is recycled in a manner that conserves valuable materials and protects human health and the environment, improper handling, accidental breakage, damage, and/or improper recycling at the end of their lifecycle may be harmful for health and environment.
EU Regulatory Compliance
Compliance with the RE Directive
Honglink Wireless Solutions Co., Ltd. declares that this device IG830E is in
compliance with the essential requirements and other relevant provisions of
the RE Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: https://www.dji.com/euro-
compliance
RF Exposure Information (SAR)
This device is designed not to exceed the emission limits for exposure to
radio waves (radio frequency electromagnetic fields) adopted by ICNIRP
guidelines and RE Directive 2014/53/EU. The radio wave exposure guidelines use
a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR
limit is 2W/kg. Testing for SAR are conducted using standard operating
positions at 0 mm distance with the device transmitting at its highest
certified power level in all tested frequency bands. The highest SAR values
for this device is XXX W/Kg.
Legal information
This device may be operated in all member states of the EU. Observe national
and local regulations where the device is used.
Frequency Bands and Power
The maximum radio-frequency power transmitted in the frequency bands in which
the radio equipment operates: The maximum power for all bands is less than the
highest limit value specified in the related Harmonized Standard.
- UMTS Band 1:
- UMTS Band 8:
- LTE Band 1/3/7/8/20/28/38/40:
UK Regulatory Compliance
Compliance with the Regulations 2017（SI 2017/2016）
Honglink Wireless Solutions Co., Ltd. declares that this device IG830E is in
compliance with the essential requirements and other relevant provisions of
the UK Radio Equipment Regulations 2017(SI2017/2016).
RF Exposure Information (SAR)
This device is designed not to exceed the emission limits for exposure to
radio waves (radio frequency electromagnetic fields) adopted by Council
Recommendation 1999/519/EC, ICNIRP Guidelines, and UK Radio Equipment
Regulations 2017 (SI 2017/1206). The radio wave exposure guidelines use a unit
of measurement known as the Specific Absorption Rate, or SAR. The SAR limit is
2W/kg. Testing for SAR are conducted using standard operating positions at 0
mm distance with the device transmitting at its highest certified power level
in all tested frequency bands. The highest SAR values for this device is XXX
W/Kg.
Frequency Bands and Power
The maximum radio-frequency power transmitted in the frequency bands in which
the radio equipment operates: The maximum power for all bands is less than the
highest limit value specified in the related Harmonized Standard.
- UMTS Band 1:
- UMTS Band 8:
- LTE Band 1/3/7/8/20/28/38/40:
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult an authorized dealer or service representative for help.
Honglink Wireless Solutions Co., Ltd. is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.
RF Exposure Information (SAR)
This device is designed not to exceed the emission limits for exposure to
radio waves (radio frequency electromagnetic fields) adopted by the Federal
Communications Commission (FCC) The radio wave exposure guidelines use a unit
of measurement known as the Specific Absorption Rate, or SAR. The SAR limit is
1.6W/kg. Testing for SAR are conducted using standard operating positions at 5
mm distance with the device transmitting at its highest certified power level
in all tested frequency bands. The highest SAR values under the FCC guidelines
for this device is 1.01 W/kg.
IC Radiation Exposure Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Important Note:
Radiation Exposure Statement:
The exposure standard for wireless transmitter employs a unit of measurement
known as the Specific Absorption Rate, or SAR. The SAR limit set by the IC is
4W/kg. The highest SAR value for the EUT as reported to the IC when
Extremityon the body, as described in this user guide, is 1.01 W/kg.