VIDALUX CO10 Whirlpool Spa Instruction Manual

VIDALUX CO10 Whirlpool Spa

Inspect bath carefully and report any damage or faults before installation. No claims can be entered in to after installation.

Protect the bath throughout installation process.

Installation must be carried out by suitably qualified tradesman in accordance with the instructions.

The quality of this product is in your hands. Please read all the instructions before starting the installation.

No installation should take place until all items have been deemed cosmetically acceptable. Once installation commences all products then enter into their governing warranty periods and no returns can be accepted, by commencing with the installation you are accepting the goods cosmetic state with all ‘workings’ being covered by warranty. (contact us for more information before installing if required)

VIDALUX CLEAR & BRIGHT WATER SOFTENER

Guaranteed to get rid of limescale

Live in a hard water area?? Limescale in the kettle and on bathroom fixtures?? Suffering from unknown adverse health effects from this polluted drinking water??

If you have a shower and any feature becomes blocked with limescale and stops working THIS IS NOT COVERED BY THE WARRANTY, as in reality it is not the products fault, it’s the poor quality water it has been subjected to

GOOD NEWS – Designed in partnership with one of the UK’s largest and most trusted water softener manufacturers, this sleek, easy fit model is GUARANTEED to work or your money back!! Remove all the limescale in a 1-4 bedroom home and benefit from the following

Better tasting drinking water – Easy to install – Guaranteed to work or your money back No plumbing or chemicals – Cost as little as £2.00 a year to run and the improved condition of the water pipes will reduce your heating bills – Made in the U.K – Trialled and tested Over 10 years | Used by professionals

IMPORTANT NOTICE

Before you proceed with fitting your Vidalux bath please read and understand the following:
By commencing testing and installation of the unit you are agreeing to the Terms and Conditions set out by us: copies of which are available by contacting us by by email or by telephone (details on the cover of this manual).
You are required to ensure the purchased product dimensions allows for ease of passage to the intended installation area.
Regarding weight tolerances of installation area, it is advisable to contact a builder or refer to Building regulations to ensure the product placement area has sufficient joist/floor support.

1. It is important that you ensure that your purchase has been delivered undamaged. You are required to check the contents and report any damage that you feel needs repairing or replacing within 48hrs of receipt of goods. Items reported damaged after this time WILL be chargeable.
2. The product you have purchased is designed for home DIY fitting. You are only required under the Terms and Conditions to get any electrics feeding the shower installed by a qualified specialist. The product requires connection to electricity and this by law requires a Part P qualified electrician. Failure to provide evidence of this will void the relating product warranty
3. We are a supply only company. If you report to us any damage we will send replacements or solutions to remedy the problem described. We endeavor to fully understand the problem first by asking a series of questions and then propose the solution. We may even ask for digital images to be sent via email to assist the process. The warranty is parts only and does NOT include fitting/inconvenience or other related costs.
4. You are required to ensure that you correctly water test any bath tub before fitting and ensure that you/ your fitter fully tests the unit upon completion and attends to any leaks and faults before he leaves.
5. All hoses, such as to the valve assembly, shower outputs and air switches and waste are fitted for transport purposes and need to be properly sealed and tightened before use. During transportation some connections can become dislodged and therefore break any watertight seal, you are required to ensure that your fitter specifically tests for these possible occurrences and seal/fix accordingly.
6. Do not book fittJOH until you have inspected the unit. We cannot be held responsible for delays and costs incurred by having to return to fit parts that need supplying.
7. We cannot be held liable for inconvenience caused due to lack of bathing facilities caused by any delay in receiving your product or whilst awaiting parts.
8. Regarding our sales and technical support: We know our products and their requirements, but we are not qualified plumbers or electricians and accept no liability for claims suggesting the same. You are advised to check the suitability of the product with a professional body. It is the customer responsibility to ensure the product is fit for purpose.
9. A ‘Completion Certificate’ is included at the end of the manual where you should record the details of your installers – you will need this to record your warranty on our website. You MUST register the product warranty within 90 days following delivery.

ATTENTION
ALWAYS FIT EASY TO GET TO ISOLATION TAPS ON BOTH THE HOT AND COLD WATER SUPPLY (NOT SUPPLIED). JUST LIKE A DISHWASHER OR WASHING MACHINE, THIS PRODUCT MUST BE ISOLATED WHEN NOT IN USE.

REMEMBER:
These baths are designed to be free standing and movable from their location should you have the need to replace anything. ALWAYS USE Flexible braided water inlet pipes (not supplied) at least a metre long (not central heating plastic type!)
Always use a flexible waste pipe from your house supply to the bath . NEVER FIX with rigid pipes, NEVER FIX the unit to the wall.

Before you begin

Assembly requires two persons.

Tools needed to assemble this shower cabin:

Electric screwdriver with a selection of heads, regular screwdrivers, pipe grips, spanners, spirit level, sharp knife and rubber mallet. Connection of the electrical supply and plumbing may require additional tools.
Do not fully tighten any screw fixings initially during build as this allows the frame to move a little and aid location of all holes and screws; remember to fully tighten before completion and subsequent use. There is a drill bit supplied with the kit, to allow either widening of holes or drilling new holes which you feel cannot be located during construction.

Water requirements

This shower requires two water supplies (1 x hot and 1 x cold) tested to be between 1 and 3 bar, with a flow rate over 7.5 litres per minute.
NOTE: We recommend water pressures over 2 bar to achieve optimum showering results.

Gravity Fed systems

If you have a Gravity fed system, then fitting a Shower Pump will almost certainly be required. Fitting a Shower pump rated over 1.5 bar is necessary as a minimum. Shower pumps MUST be properly sited, installed and commissioned. Incorrectly installed shower pumps will cause adverse affects to your showering and bathing resulting in pulsing or starting and stopping of the pump. If a pump is installed, a separate Mains Cold supply must be fitted and directed to supply the Steam Generator separately (bypassing the pump).

Isolating Valves

You MUST fit isolation valves to the shower unit on both hot and cold incoming feeds as it enables you to turn off the water supply to the shower when not in use (for example going away on holiday). Additionally isolating valves makes service checks easier than locating the house stop cock.

DUE TO THE NATURE OF THIS PRODUCT WE HIGHLY ADVISE THE PURCHASE AND FITTING OF A WATER SOFTENER
(PLEASE NOTE LIMESCALE BUILD UP MAY CAUSE DAMAGE TO YOUR SHOWER AND WILL NOT BE COVERED UNDER WARRANTY)

Electric Installation

1. Leakage protection switch must be amounted in the bathtub power supply, the power supply circuit must be fixed and well grounded. The section area of wire must not less than 2. 5mm2 and electric circuit must tally with national safety requirements which must be earth connection at earthing mark on the steel frame of bath tub(leakage protection switch will be connected by users)

Parts Name

Water-supply Installation

Piping installation
A. Water supply
Before leaving factory the cylinder tube 1s connected. Users just need to connect the external cold & hot water hose to the responding pipe joint. Pipe joint should be amount at the hidden position behind bathtub.
B. Water drainage
Connect suitable drain by 3/2 joint. Shown in the right fig.

Installation

Schematic diagram of the installation

Schematic diagram of the panel

1. water pump
2. wind pump
3. thermostatic heating
4. lock
5. bottom light
6. ozone sterilization
7. adjusting plus
8. Frequency button
9. FM radio or blue tooth button
10. adjusting minus.
11. Volume button
12. Power ON/ OFF button
    

Operation instruction and direction

1. Power ON/OFF switch
   Push down the switch, the controller is open, its status light is on, and other function can be used only when power is ON.

2. Bottom light ON/ OFF button Push down the button, the light is on; repeat the operation, the light is off.

3. water pump ON/OFF button
   Push down the button, the water pump is on; repeat the operation, the water pump is off.

4. wind pump on/ off button
   Push down the button, the wind pump is on; repeat the operation, the wind pump is off.

5. Ozone sterilization button
   Push down the button, Ozone sterilization is on; Repeat the operation , 03 will be stopped in 15 minutes when 03 is switch.

6. Thermostatic heating
   when the water pump is open, you can push down the button   Then the Heater starts to run normally. when it is pressed on long time, you can press to set the water temperature . The temperature setting range is: 30 to 50 °C. Temperature display window will flash when the temperature is set, And will display current water temperature in few seconds.

7. FM Radio & blue tooth ON/OFF
   Volume adjusting minus and Volume adjusting plus button.
   They can turn the radio step by step when they are pressed on short time. They can search the station when they are pressed on long time, it can select memory channel .

Touch the key again , the blue tooth is on . Open the Blue tooth function of the controller, then search for Blue tooth devices through devices such as mobile phone00: 1 F:81 :88:88:9E, or home music, which will prompt you to enter password, the universal code is: 000000, if the devices such as mobile phone can’t connect to Blue tooth of the controller, please restart your mobile phone and the controller.

Notice: Do not open the water pump When there is not enough water.

Run environment

Notes

1. Please read the instruction carefully before install bath tub, so that you can do it effectively
2. User should pay attention to the high-voltage on products which marked signs, Don’ t touch their locations, ensure Personal safety;
3. Don’t expose the controller to the moist or hot environment to prevent fire or electric shock. Please towel the controller after using it.
4. Please keep water clean, no solid debris left .Otherwise, it will jam the backwater and the pipeline, resulting in damaging equipment or fittings . If jam happened, please turn off the power to clean debris immediately, then restart it.
5. Please do not pull any output lines, beat or throw the equipment at random , Otherwise crusts or inner parts would be broken.
6. Don’t open the cover of the controller for there are dangerous parts in allowed for maintenance. it . Only qualified servicemen are allowed to maintenance.
7. The used power supply must be in line with the specified voltage value shown on the controller, otherwise it is not allowed to be used even burns out the controller burns out the controller.
8. The intervals of continuous power on and off must be over 30s for extending the use life of the controller.
9. Please do not plug or pull the control panel with electricity, otherwise the devices will be damaged or abnormal conditions will appear. At that moment ,turn off the power in seconds, restart it.
10. Please insert fittings(such as: light, speaker, valve ozone sterilization, water pump, wind pump, steam generator, etc.) Into corresponding output ports of equipment correctly, otherwise it world damage and cause danger order to cause danger.
11. When the 03 is on, Other key will be no action except for the power key. you can open other functions after restarting the controller, during the operation, 03 doesn’t run.
12. When water sensor is in the state of water scaritg or doesn’t reach the standard level, It’s prohibited to open water pump, wind pump or Heater.(if the product can detecting water level.)

Solutions of basic problems

1. Q: Why do water pump, wind pump or thermostat heating not run?
   A: Please check whether there is any equipment with water level ,if so, please check whether the water sensor connect water is well ,if not, please stop using it, then you can contact with my company staff.

2. Q: Press lights, ozone, speakers, fan, air-conditioning and other functions, but why don’t they start to run?
   A. check whether the plug-in terminals connect each other well ; if lights and ozone sterilization still fails to run, please turn on the “use and ensure it has blew out, pis contact with my company staff.

3. Q: If speaker is voiceless, why is that?
   A: Please open the FM radio, check whether the volume button on the panel has been Increased. If not, you can contact with my company staff. Reference to the following reasons: Speaker’s terminal connection badly; Internal chips had burned out; the corresponding relay is open; the Speaker is broken.

4. Q: If there is little FM radio program received or sound effect is bad, why is that?
   A. Please check the location of the antenna, release antenna or to remove it to another appropriate location.

Cleaning & Maintaining

1. Cleaning with liquid scour and soft cloth. Caution: acetone, ammonia, carbinol, formyl, formal dehydeetc are forbidden 2.If there are some scratche on the surface, polish them with 2000# sandpaper, then plaster some toothpaste and use soft cloth to keep the whirlpool shining ..
2. If there are some scratche on the surface, polish them with 2000# sandpaper, then plaster some toothpaste and use soft cloth to keep the whirlpool shining ..
3. Exterior furring can be removed by acid scour and soft cloth, you’d better use hot citricacid vinegar to clean.
4. If you find the overflow and drain are blocked by dirties, screw it off and clean.
5. Gold and chrome finished accessories don’t need much wiping.
6. Don’t clean the bathtub with rough tools or detergent with chemicals solvents.
7. When you finish using the bathtub, drain and power off
8. Don’t hammer and carve the bathtub with blunt object or some thing very sharp ..
9. Filling the whirlpool fully with 40°C warm water for whole whirl pool clean, mixed with 2g scour and start the massage power for 5 minutes, switch and drain, then filling cold water fully and start the massage power for about 3 minutes, drain and whirlpool clean finished.

Safety Guide

1. Whirlpool should be installed by professional worker, otherwise we would not be responsible for it.
2. Electrical source parameter should in accordance with national standard, such as including leakage protection switch. Pay attention to the switch, the electric outlet and the electric wire are all waterproof
3. Don’t use too hot water, and obey the rules: cold water first, hot water next. Don’t power on unless the water cover the jets.
4. 220V is the standard udtage for the bathtub. Don’t power on if the voltage is 235V or I90V
5. Make sure power off after using the bathtub.

Trouble Shootings

1. Power is not on and leakage protection switch is off

|

1. Turn on power and leakage protection switch

2. Dirt block the pump vane| 2. Remove dirt
3. Pump switch is not on| 3. Turn on pump switch
4. Water pump damaged| 4. Repair or replace pump
5. Air pipe and switch loose or leakage| 5.Fasten air pipe and check air switch
6. Power plug loose| 6.Plug power plug
Air pump doesn’t work| 1. Power isn’t normal| 1.Check power circuit and plug power plug
2. Air pipe and switch loose or leakage| 2.Fasten air pipe and check air switch
3.Air switch is off or damaged| 3.Check air switch
Massage force can’t be adjusted| 1. Voltage is not normal|

1. Check voltage

2. Adjusting switch is off or damaged| 2. Check adjusting switch or replace it
3. Backwater hole is blocked| 3. Clean backwater hole
Bathtub isn’t horizonal| 1. Supporting leg don’t adjusted well| I. Adjust supporting leg
Water leakage out of pipe| I .Seal ring damaged| I .Replace seal ring
2. Nut isn’t locked| 2. Lock nut
3. Bad sealed between interface| 3. Keep well glued between interface
Apron doesn’t wel1installed| Adjust apron support aimed at apron screw position

FOR TECHNICAL ASSISTANCE PLEASE EMAIL US ON:

sales@vidalux.co.uk
OR CALL US ON:
01524 489939

References

• Vidalux - Steam Showers, Hydro & Whirlpools Baths - UK's biggest & Best

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>