Global Wt Industrial WT08 Walkie Talkie Radio User Manual
- June 6, 2024
- Global Wt Industrial
Table of Contents
Global Wt Industrial WT08 Walkie Talkie Radio
INSTALLATION
Functional description
- Battery: This machine uses 4 No. 7 batteries.
- Belt clip: This machine is easy to use with belt clip.
- Call (CALL key): Press this key to send a call signal to other walkie-talkies.
- Display screen (LCD): Multi-purpose display, which can display channels, volume and other usage status.
- Switch on/off ( keys): Long press 3s the power off key to switch on and off.
- Lighting keys (LAMP keys): Long press 3s to make the lamp light up.
- Channel Scan Key (SCAN key): short press this key to perform/stop channel scanning function.
- Function key (MENU key): short press select key for channel and function.
- Monitor key (MON key): Long press 3s that can continuously monitor weak signals.
- Speech key (PTT key): Press to make a call.
- Up and down adjustment key (UP/DOWN key): Use this key up and down to adjust the channel, volume and other usage status.
- 12.Headphone/microphone/chargingjack(SPK/MIC/CHG): connecting with External headphone/microphone/power charger.
Installation Instructions
Installation and disassembly of belt clip:
Insert the belt clip into the belt slot and push it down to the end. If you want to take off the belt clip, first break the mortise and gently push the belt clip upward (Fig. 1).
Battery Installation:
Remove the belt clip, open the button of the battery cover and open the battery cover. Installation of 4 No. 7 batteries, please pay attention to the correct positive and negative poles.
Install battery cover and belt clip.
Note: If you do not use this unit for a long time, please remove the battery (Figure 2).
Hanging Rope Installation
The walkie-talkie rope can be hung through a small hole in the belt clip (Fig. 3).
Operational Instructions
Start-up: Long press keys when there is a short tone, showing display screen appears, it is completed.
-
Shutdown: The long press when there is a short tone, showing display screen disappears.
-
Adjust the volume: Use the adjusting key ( big) ( small) to adjust the volume, the volume is displayed in the lower right corner of the display screen.
-
Receive calls: When the machine is in the boot state and does not speak, and is not used as a caller, the machine is in the receiving state. If the currently set channel receives the signal, the upright corner of the display screen will display the receiving symbols.
-
Speech: If you want to speak, you should press the PTT key continuously. After speaking, you can release the PTT key. The upright corner of the screen will show the speech symbol. Pronounce at normal volume. The best distance from the microphone is 10 centimeters.
Note: If more than one party communicates, they must choose the same channel to communicate with each other. -
Channel Locking Function: Press + MENU key for about 2 seconds, the display screen appears symbols, which means that the channel is locked. At this time, it is impossible to choose better channels. Press + MENU key again for about 2 seconds to unlock the channel.
-
Lighting function: This machine has external lighting function. Press the LAMP key for 3s, the lamp will be on and can be used as a flashlight.
-
Channel Selection: If you need to change the channel, press the MENU key first, then the CH symbol and channel number After pressing the or key to select the channel you need, press PTT or MON key to store the data and return to the normal display state, or press the MENU key to confirm the channel and enter the call ring tone selection. Choose the state.
-
Call Ringtone Selection: This machine can set up five different call ringtones, but also can turn off the ringtone. If you need to set the ringtone, press the MENU key twice, then the display screen will flash CA symbols and ringtone code (1,2,3,4,5,oF), then press the or key to adjust to the required ringtone, after selection, press PTT key to store data and return to the normal display state, or press the MENU key to confirm the selection and return to the normal display state.
-
Channel Scanning: Press the SCAN key, this opportunity automatically stops according to the scanning channel to select a currently effective channel. When this channel is found, this opportunity stays in the channel and plays the received signal. If you want to continue scanning other channels, you can press the key to continue scanning. Press the SCAN key again to stop, press the SCAN key again. PTT keys can be used to speak and out of the scanning state.
-
Call others: This function is used to start or end a call, or to notify other phones of the same channel. When the CALL key is pressed, all phones that have been turned on and in the same channel within a valid distance will receive a call bell.
-
Monitor: Use this function to monitor weak signals. Press the MON key to proceed. If you want to continue, please hold down the MON key for at least 3 seconds. If you want to stop, press the MON key again.
-
Electric power indication: This machine will display in the lower power at the left corner of the display screen according to the battery stock. When the battery symbol flickers, it indicates that the power is insufficient and the battery must be replaced.
-
Earphone/microphone: This machine has an external earphone/microphone interface, which can be used to communicate and speak with earphone/microphone. To use this function, please remove the rubber plug on the headphone hole above the headphone, insert the headphone plug into the headphone and microphone jack and put on the headphone.
-
Charging: This machine has charging battery interface. When charging, please plug the charger plug into the headset/microphone/charging Jack to charge directly.
Note: This machine can not be used when charging with plug.
Specification
- Channel: Channel is optional.
- Distance: up to 5 KM.
Notes: When using headphones, please adjust the volume appropriately. If you feel uncomfortable with your ears, please shut down immediately. Do not use this machine in unsafe environment to avoid explosion or fire. For example, gas stations, undetected power facilities and other unsafe places.
- Simple Maintenance: Please wipe the dust and dirt with soft cloth, and do not use any cleaner or chemical agent to avoid damaging the machine. If the machine is wet, please shut down immediately, remove the battery, dry it with a soft cloth, and place it in a dry and cool place. Do not turn on the machine before it is dry. If there is any problem or local malfunction, please send it to the vendor or the service department of our company for treatment. Do not disassemble and repair it by yourself.
Simple troubleshooting
- Unable to start: Please check if the battery is valid and installed properly for proper replacement and installation.
Poor reception:
- 1. Press the button to turn up the volume. Please confirm whether the reception is bad. If yes, press the MON key to enhance the reception.
- 2. Check whether the battery is sufficient.
Our Global WT Industrial Co., Ltd. radio generators RF electromagnetic energy during transmit mode.This radio is designed for and classified as“Occupational Use Only”,meaning it must be used only during the course of employment by individuals aware of the hazards,and the ways To Minimize Such hazards. This radio is NOT intended for use by the“General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for“Occupational Use Only”. Inaddition, our Global WT Industrial Co., Ltd. radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:
- IEEE Std. 1528:2013 and KDB447498, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
- American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
- American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields-RF and Microwave.
FCC statment
The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, Global WT Industrial Co., Ltd. radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.
Attention
This radio complies with IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environment at operating duty factors of up to 50% and is authorized by the FCC for occupational use only. An appropriate warning label is affixed to all units. In order to comply with RF exposure requirements, a minimum distance of 2.5 cm must be maintained when held-to-face and body-worn operations are restricted to the approved original accessories (belt clip), a minimum distance of 0 cm. Do not use this device when the antenna shows obvious damage. This product is in compliance to FCC RF Exposure requirements and refers to FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm Search for FCC ID: 2AMS2-WT08 to gain further information including SAR Values.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>