Shark IR140 Series ION X40 Cordless Vacuum FAQs
- June 9, 2024
- Shark
Table of Contents
Shark IR140 Series ION X40 Cordless Vacuum FAQs
This article contains the FAQs for the IR140 Series Shark® ION™ X40. This supports the following product SKUs IR140, IR140C, IR142C, IR141, IR142.
FAQs
General questions:
How is a Shark vacuum with DuoClean Technology different than
traditional vacuums?
The Shark IONFlex Cord-Free Ultra-Light vacuum is equipped with DuoClean Technology. Instead of a single brushroll, it has two brushrolls engineered to work in unison, removing large debris and fine dust particles from your floors and carpets.
How do I attach accessories to the vacuum?
There are two ways to clean with the accessories.
Either separate the handheld portion from the rest of the vacuum by pressing the “Wand Release” button or keep the wand connected to the handheld and remove the floor nozzle by stepping on the foot pedal release.
Choose the desired cleaning accessory and slide it onto the end of the handheld vacuum or the end of the wand.
Note that the accessories do not need to be pushed all the way onto the vacuum to be secure. Only the Deep-Cleaning Motorized Pet Tool clicks into place. Also note that the wand can bend for more flexible reach by using the MultiFLEX feature.
How do I turn the vacuum off?
To turn the vacuum off, press the power button.
How do I store my vacuum?
MultiFLEX technology allows you to store this vacuum in a compact, upright position. Hold down the “Press to Unlock” button and gently fold the handheld vacuum forward toward the floor nozzle. Use the handle to carry the vacuum to its storage location.
Another option is to simply lay the vacuum flat on the floor. There are rubber pads on the base of the handheld vacuum that prevent scratching. Wall mounts are also available for purchase
How long does it take to fully charge the battery?
It takes approximately 3.5 hours to reach a full charge.
What is the runtime of the battery on a full charge?
A single power pack runtime is approximately 40 minutes with new battery on ION POWER in handvac mode. You can benefit from hassle-free cleanability by swapping out with a second battery which will give you approximately 80 minutes of cleaning in extended runtime mode.
– The ION Power Pack, like all lithium-ion products, will naturally decrease
in capacity over time from the 100% capacity of a new battery.
– These times are based on 100% capacity.
Mode – Expected Run Time:
- Hand vacuum only in ION POWER mode: approximately 40 minutes
- Hand vacuum only in ION BOOST mode: approx. 12 minutes
- Floor mode in ION POWER: approx. 31 minutes
- Floor mode in ION BOOST: approx. 11minutes
- Carpet mode in ION POWER: approx. 26 minutes
- Carpet mode in ION BOOST: approx. 10 minutes
General questions about using the vacuum:
How do I begin cleaning floors?
The Shark ION F80 Cord-Free/ IONFlex 2X vacuum has two floor settings for cleaning ” a Bare floor, Area Rug Setting and a High Pile Carpet Setting.
It also has two power settings ION Power and ION Boost. Use ION Power for your everyday cleaning and switch to ION Boost if you need a 1-minute boost of increased suction power for small messes and heavy traffic areas.
How do I remove the handheld vacuum to clean “above floors?”
Press the “Wand Release” button at the top of the wand and pull the handheld vacuum off, separating it from the rest of the vacuum. Attach desired accessory and begin cleaning.
How do I remove the handheld vacuum with extension wand to clean “above
floors?”
Step on the “Wand Release” foot pedal on the floor nozzle and pull the wand off. Attach desired accessory to the end of the wand and begin cleaning.
General questions about maintenance:
How do I celan the filters and how often?
The pre-motor filters are located on the top of the handvac. Turn off the power and remove the battery. Place the rest of the vacuum on the floor. Pull out the filter assembly. Gently separate the cylindrical foam filter from the felt. Rinse both filters with water until the water runs clear.
Once completely dry, slide the foam filter back onto the felt filter and reinstall.
The post-motor filter is located under the handle of the vacuum. Press the button to remove the cover and pull out this filter. Rinse with water until the water runs clear.
Once completely dry, reinstall the filter under the handle and press the cover closed until it clicks into place.
DO NOT use soap. Let air dry completely (at least 24 hours) before reinstalling
How do I empty the dust cup and how often?
First, turn the power off and remove the battery. Then, separate the handheld from the rest of the vacuum by pressing the “Wand Release” button. Next, hold the dust cup over the trash and press the “Empty” button. Tap gently to empty contents and pull any debris off of the metal screen. If desired, wipe clean with a dry soft cloth. Close the lid. You will hear it click into place.
For optimal performance, the dust cup should be emptied each time you vacuum and when the dust cup appears full or debris reaches the “MAX FILL” line.
How do you maintain the brushroll and softroller?
First, turn off the power. Then, remove the brushroll garage located on the top of the nozzle by sliding both “Access Brush Roll” buttons toward the back of the nozzle.
Brushroll:
Remove any string, hair, or debris that may be wrapped around the brushroll by running scissors or the lower corner of the garage lid along the guide on the brushroll.
Softroller:
Pull out the soft roller using the “Pull” tab located on the right side of the roller.
Remove any debris from the soft roller housing. Wipe the soft roller with a dry paper towel. If desired, wash the roller with water only and let air dry completely before reinstalling (24 hours).
Reinsert the soft roller by sliding it into the front of the nozzle, starting on the left side, until it clicks into place.
Close the brushroll garage by inserting the tabs on the lid into the slots, then pressing down on both sides of the lid until it clicks into place
How do I charge the battery?
Connect the ION Power Pack Battery Charger to the port on the side of the ION Power Pack Battery, then plug the charger into a wall outlet. The ION Power Pack Battery can be charged whether it is inside or outside the handheld vacuum.
If you have the charging dock:
Connect ION Power Pack Battery Charger to the Charging Dock. Place power pack onto dock, then connect charger to wall outlet.
Product Specifications:
Where is the product made?
The Shark IONFlex Cord-Free Ultra-Light is manufactured by our high-quality vacuum manufacturing partners in China.
What is the vacuum made of?
The Shark ION X40 Cord-Free Ultra-Light is produced with a combination of durable ABS and PP plastics, along with some metal and rubber components.
What is the weight of the vacuum?
8.7 lbs. (no accessories)
What are the dimensions of the vacuum?
13.4″ L X 10.2″ W X 45.9″ H
What is the dirt capacity of the dust cup?
0.3 dry quarts
What is the voltage?
25.2 Volts
What is the Wattage?
300 Watts
What is the Amperage?
11.9 Amps