Surenoo SMC0350C-320480 Series MCU Interface TFT LCD Module User Manual

Surenoo SMC0350C-320480 Series MCU Interface TFT LCD Module

Product Description

The product is a 3.5-inch TFT LCD display module which supports switching between resistance touch screen and capacitive touch screen. It has 480×320 resolution, supports 16BIT RGB 65K color display, and the internal driver IC is NT35310, which uses 16-bit parallel port communication. The module includes LCD display, resistance touch screen or capacitance touch screen and PCB backplane. It can be plugged into the TFT LCD slot of the STM32 series development board or used on the C51 platform.

Product Features

• 3.5-inch color screen, support 16BIT RGB 65K color display, display rich colors
• 320×480 resolution for clear display
• Support 16-bit parallel data bus mode switching, fast transfer speed
• Supports ALIENTEK STM32 Mini, Elite, WarShip, Explorer, and Apollo development boards direct plug-in use
• Support switching between resistance touch screen and capacitive touch screen
• Provides a rich sample program for STM32 and C51 platforms
•  Military-grade process standards, long-term stable work
•  Provide underlying driver technical support
  Name| Description
  ---|---
  Display Color| 16BIT RGB 65K color
  SKU| MRB3512
  Screen Size| 3.5(inch)
  Screen Type| TFT
  Driver IC| NT35310
  Resolution| 480*320 (Pixel)
  Module Interface| 16Bit parallel interface
  Active Area| 48.96×73.44 (mm)
  Touch Screen Type| Resistance touch screen or

Capacitive touch screen

Touch IC| Resistance touch screen:XPT2046

Capacitive touch screen :GT911

Module PCB Size| 56.41×97.60 (mm)
Operating Temperature| -10℃~60℃
Storage Temperature| -20℃~70℃
Operating Voltage| 3.3V / 5V
Power Consumption| TBD
Product Weight(Including packaging)| 57g

Product Parameters

NOTE:

1. The hardware of the module supports switching between resistance touch screen and capacitive touch screen (as shown in the dotted line box in Picture 1 above), as follows:
   A. Use resistance touch screen: solder the components in the dotted line box of RTOUCH, and do not need to weld the components in the dotted line box of CTOUCH;
   B. Use capacitive touch screen: solder the components in the dotted line box of CTOUCH, and do not need to weld the components in the dotted line  box of RTOUCH;

2. This module can be directly inserted into the TFTLCD slot of the punctual atom development board, no manual wiring is required. 3

3. The hardware of this module only supports 16 bit mode

Important Note:

1. The following pin numbers 1~34 are the pin number of Module pin with PCB backplane of our company. If you purchase a bare screen, please refer to the pin definition of the bare screen specification, refer to the wiring according to the signal type instead of directly Wire according to the following module pin numbers. For example: CS is 1 pin on our module. It may be x pin on different size bare screen.
2. About VCC supply voltage: If you buy a module with PCB backplane, VCC/VDD power supply can be connected to 5V or 3.3V (module has integrated ultra low dropout 5V to 3V circuit), if you buy a bare screen LCD, remember to only connect 3.3V.
3. About the backlight voltage: The module with the PCB backplane has integrated triode backlight control circuit, which only needs to input the high level of the BL pin or the PWM wave to illuminate the backlight. If you are buying a bare screen, the LEDAx is connected to 3.0V-3.3V and the LEDKx is grounded.
   Number| Module Pin| Pin Description
   ---|---|---
   1| CS| LCD reset control pin( low level enable)
   2| RS| LCD register / data selection control pin

(high level: register, low level: data)

3| WR| LCD write control pin
4| RD| LCD read control pin
5| RST| LCD reset control pin( low level reset)
6| D0| LCD data bus 16-bit pin
8| D2| **
9| D3| **
10| D4| **
11| D5| **
12| D6| **
13| D7| **
14| D8| **
15| D9| **
16| D10| **
17| D11| **
18| D12| **
19| D13| **
20| D14| **
21| D15| **
22| GND| Module power ground pin
23| BL| LCD backlight control pin(High level light)
24| VDD| Module power positive pin (module has integrated voltage regulator IC, It can be connected to 5V or 3.3V on STM32 and 5V on

C51)

25| VDD| **
26| GND| Module power ground pin
27| GND| **
28| NC| LCD backlight power positive pin (default shared onboard backlight power supply, this pin can not be

connected)

29| MI| Resistance touch screen SPI bus read signal
30| MO| Resistance touch screen SPI bus write signal or capacitance touch screen IIC bus data signal
31| PEN| Capacitive or resistive touch screen interrupt

detection pin (low level when touch occurs)

32| NC| Not defined, no need to use
33| TCS| Resistance touch screen chip selection control signal or capacitive touch screen reset signal (low level reset)
34| TCK| Resistance touch screen SPI bus or capacitive touch screen IIC bus clock signal

Hardware Configuration

The LCD module hardware circuit comprises six parts: an LCD display control circuit, a power control circuit,a Impedance balance adjusting circuit, a capacitive touch screen control circuit , a resistance touch screen control circuit and a backlight control circuit. LCD display control circuit for controlling the pins of the LCD, including control pins and data transfer pins. Power control circuit for stabilizing the supply voltage and selecting the external supply voltage The impedance balance adjusting circuit is used to balance the impedance between MCU pin and LCD pin. resistance touch screen control circuit is used to control touch screen interrupt acquisition, data sampling, AD conversion, data transmission, etc Capacitive touch screen control circuit is used to control touch screen interrupt acquisition, data sampling, AD conversion, data transmission, etc. A backlight control circuit is used to control the brightness of the backlight.

working principle

1. Introduction to NT35310 Controller
   The NT35310 controller supports a maximum resolution of 320*480 and has a 345600-byte GRAM. It also supports 8-bit, 9-bit, 16-bit, 18-bit parallel port data buses. It also supports 3-wire and 4-wire SPI serial ports. Since the supported resolution is relatively large and the amount of data transmitted is large, the parallel port transmission is adopted, and the transmission speed is fast. NT35310 also supports 65K, 262K and color display, display color is very rich, while supporting rotating display and scroll display and video playback, display in a variety of ways.
   The NT35310 controller uses 16bit (RGB565) to control a pixel display, so it can display up to 65K colors per pixel. The pixel address setting is performed in the order of rows and columns, and the incrementing and decreasing direction is determined by the scanning mode. The NT35310 display method is performed by setting the address and then setting the color value.

2. Introduction to parallel port communication
   The parallel port communication write mode timing is as shown below:
   
   
   The timing of the parallel port communication read mode is shown in the figure below:
   
   

CSX is a chip select signal for enabling and disabling parallel port communication, active low DCX is the data or command selection signal, 1-write data or command parameters, 0-write command WRX is a write data control signal RDX is a read data control signal Host-D[17:0] is a parallel port data bit, which has four types: 8-bit, 9-bit, 16-bit, and 18-bit.
When performing a write operation, on the basis of the reset, first set the data or command selection signal, then pull the chip select signal low, then input the content to be written from the host, and then pull the write data control signal low. When pulled high, data is written to the LCD control IC on the rising edge of the write control signal. Finally, the chip select signal is pulled high and a data write operation is completed. When entering the read operation, on the basis of the reset, first pull the chip select signal low, then pull the data or command select signal high, then pull the read data control signal low, and then read the data from the LCD control IC. And then The read data control signal is pulled high, and the data is read out on the rising edge of the read data control signal. Finally, the chip select signal is pulled high, and a data read operation is completed.

Instructions for use

STM32 instructions
Wiring instructions : See the interface description for pin assignments.
Note:

1. This module can be directly inserted into the TFTLCD slot of the punctual atom development board, no manual wiring is required.
2. The following internal plug-in pins of the corresponding MCU refer to the MCU pins directly connected to the TFTLCD slot inside the development board, only for reference.

MiniSTM32 development board TFTLCD socket in-line instructions

Number| Module Pin| Corresponding

TFTLCD socket pin

| Corresponding to STM32F103RCT6

microcontroller internal connection pin

1| CS| CS| PC9
2| RS| RS| PC8
3| WR| WR| PC7
4| RD| RD| PC6
5| RST| RST| PC4
6| D0| D0| PB0
7| D1| D1| PB1
8| D2| D2| PB2
9| D3| D3| PB3
10| D4| D4| PB4
11| D5| D5| PB5
12| D6| D6| PB6
13| D7| D7| PB7
14| D8| D8| PB8
15| D9| D9| PB9
16| D10| D10| PB10
17| D11| D11| PB11
18| D12| D12| PB12
19| D13| D13| PB13
20| D14| D14| PB14
21| D15| D15| PB15
22| GND| GND| GND
23| BL| BL| PC10
24| VDD| 3.3| 3.3V
25| VDD| 3.3| 3.3V
26| GND| GND| GND
27| GND| GND| GND
28| NC| Not used| 5V
29| MI| MISO| PC2
30| MO| MOSI| PC3
31| PEN| PEN| PC1
32| NC| Not used| NC
33| TCS| TCS| PC13
34| TCK| CLK| PC0
Elite STM32 development board TFTLCD socket in-line instructions
Number| Module Pin| Corresponding TFTLCD socket pin| Corresponding to STM32F103ZET6 microcontroller internal connection pin
1| CS| CS| PG12
2| RS| RS| PG0
3| WR| WR| PD5
4| RD| RD| PD4
5| RST| RST| reset pin
6| D0| D0| PD14
7| D1| D1| PD15
8| D2| D2| PD0
9| D3| D3| PD1
10| D4| D4| PE7
11| D5| D5| PE8
12| D6| D6| PE9
13| D7| D7| PE10
14| D8| D8| PE11
15| D9| D9| PE12
16| D10| D10| PE13
17| D11| D11| PE14
18| D12| D12| PE15
19| D13| D13| PD8
20| D14| D14| PD9
21| D15| D15| PD10
22| GND| GND| GND
23| BL| BL| PB0
24| VDD| VDD| 3.3V
25| VDD| VDD| 3.3V
26| GND| GND| GND
27| GND| GND| GND
28| NC| Not used| 5V
29| MI| MISO| PB2
30| MO| MOSI| PF9
31| PEN| PEN| PF10
32| NC| Not used| NC
33| TCS| TCS| PF11
34| TCK| CLK| PB1
WarShip STM32 development board TFTLCD socket in-line instructions
Module Pin| Corresponding TFTLCD socket pin| Corresponding to STM32F103ZET6

microcontroller internal connection pin

V2| V3
CS| CS| PG12
RS| RS| PG0
WR| WR| PD5
RD| RD| PD4
RST| RST| reset pin
D0| D0| PD14
D1| D1| PD15
D2| D2| PD0
D3| D3| PD1
D4| D4| PE7
D5| D5| PE8
D6| D6| PE9
D7| D7| PE10
D8| D8| PE11
D9| D9| PE12
D10| D10| PE13
D11| D11| PE14
D12| D12| PE15
D13| D13| PD8
D14| D14| PD9
D15| D15| PD10
GND| GND| GND
BL| BL| PB0
VDD| VDD| 3.3V
VDD| VDD| 3.3V
GND| GND| GND
GND| GND| GND
NC| Not used| 5V
29| MI| MISO| PF8| PB2
30| MO| MOSI| PF9
31| PEN| PEN| PF10
32| NC| Not used| NC
33| TCS| TCS| PB2| PF11
34| TCK| CLK| PB1
Explorer STM32F4 development board TFTLCD socket in-line instructions
Number| Module Pin| Corresponding

TFTLCD socket pin

| Corresponding to STM32F407ZGT6

microcontroller internal connection pin

1| CS| CS| PG12
2| RS| RS| PF12
3| WR| WR| PD5
4| RD| RD| PD4
5| RST| RST| reset pin
6| D0| D0| PD14
7| D1| D1| PD15
8| D2| D2| PD0
9| D3| D3| PD1
10| D4| D4| PE7
11| D5| D5| PE8
12| D6| D6| PE9
13| D7| D7| PE10
14| D8| D8| PE11
15| D9| D9| PE12
16| D10| D10| PE13
17| D11| D11| PE14
18| D12| D12| PE15
19| D13| D13| PD8
20| D14| D14| PD9
21| D15| D15| PD10
22| GND| GND| GND
23| BL| BL| PB15
24| VDD| VDD| 3.3V
25| VDD| VDD| 3.3V
26| GND| GND| GND
27| GND| GND| GND
28| NC| Not used| 5V
29| MI| MISO| PB2
30| MO| MOSI| PF11
31| PEN| PEN| PB1
32| NC| Not used| NC
33| TCS| TCS| PC13
34| TCK| CLK| PB0
Apollo STM32F4/F7 development board TFTLCD socket in-line instructions

Number

| ****

Module Pin

| Corresponding TFTLCD socket pin| Corresponding to STM32F429IGT6、STM32F767IGT6、STM32H743IIT6

microcontroller internal connection pin

1| CS| CS| PD7
2| RS| RS| PD13
3| WR| WR| PD5
4| RD| RD| PD4
5| RST| RST| reset pin
6| D0| D0| PD14
7| D1| D1| PD15
8| D2| D2| PD0
9| D3| D3| PD1
10| D4| D4| PE7
11| D5| D5| PE8
12| D6| D6| PE9
13| D7| D7| PE10
14| D8| D8| PE11
15| D9| D9| PE12
16| D10| D10| PE13
17| D11| D11| PE14
18| D12| D12| PE15
19| D13| D13| PD8
20| D14| D14| PD9
21| D15| D15| PD10
22| GND| GND| GND
23| BL| BL| PB5
24| VDD| VDD| 3.3V
25| VDD| VDD| 3.3V
26| GND| GND| GND
27| GND| GND| GND
28| NC| Not used| 5V
29| MI| MISO| PG3
30| MO| MOSI| PI3
31| PEN| PEN| PH7
32| NC| Not used| NC
33| TCS| TCS| PI8
34| TCK| CLK| PH6
| | | | |

Operating Steps：
A. Connect the LCD module(As shown in Picture 1) and the STM32 MCU according
to the above wiring instructions, and power on;
B. Select the C51 test program to be tested, as shown below:
(Please refer to the test program documentation for the test program
description.)

Open the selected test program project, compile and download; detailed description of the STM32 test program compilation and download can be found in the following document:
http://www.lcdwiki.com/res/PublicFile/STM32_Keil_Use_Illustration_EN.pdf
D. If the LCD module displays characters and graphics normally, the program runs successfully；
C51 instructions

Wiring instructions: See the interface description for pin assignments.
Note:

1. Since the input and output levels of the GPIO of the STC12C5A60S2 microcontroller are 5V, the capacitive touch IC cannot work normally (only 1.8~3.3V can be accepted). If you want to use the capacitive touch function, you need to connect to the level conversion module;
2. Since the STC89C52RC microcontroller does not have a push-pull output function, the backlight control pin needs to be connected to a 3.3V power supply to be properly lit.
3. Since the STC89C52RC microcontroller’s Flash capacity is too small (less than 25KB), the program with touch function cannot be downloaded, so the touch screen does not need wiring.
    | STC12C5A60S2 microcontroller test program wiring instructions
   ---|---
    | ****

Module Pin

| Corresponding to STC12 development board

wiring pin

 | CS| P13
 | RS| P12
 | WR| P11
 | RD| P10
 | RST| P33
 | D0| P00
 | D1| P01
 | D2| P02
 | D3| P03
 | D4| P04
 | D5| P05
 | D6| P06
 | D7| P07
 | D8| P20
 | D9| P21
 | D10| P22
 | D11| P23
 | D12| P24
 | D13| P25
 | D14| P26
 | D15| P27
 | GND| GND
 | BL| P31
 | VDD| 5V
 | VDD| 5V
 | GND| GND
 | GND| GND
 | NC| No need to connect
 | MI| No need to connect
30| MO| P34
31| PEN| P32
32| NC| No need to connect
33| TCS| P37
34| TCK| P36
1| CS| P13
2| RS| P12
3| WR| P11
4| RD| P10
5| RST| P14
6| D0| P30
7| D1| P31
8| D2| P32
9| D3| P33
10| D4| P34
11| D5| P35
12| D6| P36
13| D7| P37
14| D8| P20
15| D9| P21
16| D10| P22
17| D11| P23
18| D12| P24
19| D13| P25
20| D14| P26
21| D15| P27
22| GND| GND
23| BL| 3.3V
24| VDD| 5V
25| VDD| 5V
26| GND| GND
27| GND| GND
28| NC| No need to connect
29| MI| No need to connect
30| MO| No need to connect
31| PEN| No need to connect
32| NC| No need to connect
33| TCS| No need to connect
34| TCK| No need to connect
| | |

Operating Steps：
A. Connect the LCD module (As shown in Picture 1)and the C51 MCU according tothe above wiring instructions, and power on;
B. Select the C51 test program to be tested, as shown below:
(Test program description please refer to the test program description document in the test package)

C. Open the selected test program project, compile and download; detailed description of the C51 test program compilation and download can be found in the following document:
http://www.lcdwiki.com/res/PublicFile/C51_Keil%26stc- isp_Use_Illustration_EN.pdf
D. If the LCD module displays characters and graphics normally, the program runs successfully；

Software Description

1. Code Architecture
   A. C51 and STM32 code architecture description The code architecture is shown below: Sample code
   
   The Demo API code for the main program runtime is included in the test code; LCD initialization and related bin parallel port write data operations are included in the LCD code; Drawing points, lines, graphics, and Chinese and English character display related operations are included in the GUI code; The main function implements the application to run; Platform code varies by platform; The IIC code is used by the capacitive touch IC GT911, including IIC initialization, data writing and reading, etc; Touch code includes two parts: resistance touch screen code and capacitance touch screen (gt911) code; The key processing related code is included in the key code (the C51 platform does not have a button processing code); The code related to the led configuration operation is included in the led code(the C51 platform does not have a led processing code);

2. GPIO definition description
   A. STM32 test program GPIO definition description The GPIO definition of the LCD screen of the STM32 test program is placed in the lcd.h file, which is defined in two ways: 1) STM32F103RCT6 microcontroller test program uses IO analog mode (it does not support FSMC bus) 2) Other STM32 MCU test programs use FSMC bus mode STM32F103RCT6 MCU IO analog test program LCD screen GPIO definition as shown below:
   
   FSMC test program lcd screen GPIO is defined as shown below (take STM32F103ZET6 microcontroller FSMC test program as an example):
   
   STM32 platform touch screen related code contains two parts :resistance touch screen code and capacitance touch screen code. Resistance touch screen GPIO definition is placed in the rtp.h file as shown below (take the STM32F103ZET6 microcontroller IO analog test program as an example):
   
   The capacitance touch screen related GPIO definition consists of two parts: IIC’s GPIO definition and screen interrupt and reset GPIO definition. The IIC GPIO definition is placed in the ctpiic.h file as shown below (take the STM32F103RCT6 microcontroller FSMC test program as an example):
   
   The interrupt of the touch screen and the reset GPIO definition are placed in GT911.h, as shown in the following figure (take the STM32F103ZET6 microcontroller FSMC test program as an example):
   
   B. C51 test program GPIO definition description C51 test program lcd screen GPIO definition is placed in the lcd.h file, as shown below(Taking the STC12C5A60S2 microcontroller test program as an example):
   
   Parallel pin definition needs to select the whole set of GPIO port groups, such as P0, P2, etc., so that when transferring data, the operation is convenient.Other pins can be defined as any free GPIO. C51platform touch screen related code contains two parts :resistance touch screen code and capacitance touch screen code. Resistance touch screen GPIO definition is placed in the rtp.h file as shown below (Taking the STC12C5A60S2 microcontroller test program as an example):
   The capacitance touch screen related GPIO definition consists of two parts: IIC’s GPIO definition and screen interrupt and reset GPIO definition. The IIC GPIO definition is placed in the gtiic.h file as shown below (take the STC12C5A60S2 microcontroller test program as an example):
   
   The interrupt of the screen and the reset GPIO definition are placed in GT911.h, as shown in the following figure (take the STC12C5A60S2 microcontroller test program as an example):
   The GPIO definition of the touch screen can be modified and can be defined as any other free GPIO.

3. Parallel port communication code implementation
   A. STM32 test program parallel port communication code implementation The STM32 test program parallel port communication code is placed in the LCD.c file, which is implemented in two ways: 1) STM32F103RCT6 microcontroller test program uses IO analog mode (it does not support FSMC bus) 2) Other STM32 MCU test programs use FSMC bus mode The IO simulation test program is implemented as shown below:
   
   The FSMC test program is implemented as shown below:
   
   Both 8- and 16-bit command writes and 8- and 16-bit data writes and reads are implemented.

B. C51 test program parallel port communication code implementation The relevant code is implemented in the LCD.c file as shown below:
Implemented 8-bit and 16-bit commands and 8-bit and 16-bit data write and read.

4. touch screen calibration instructions
   A. STM32 test program touch screen calibration instructions The STM32 touch screen calibration program automatically recognizes whether calibration is required or manually enters calibration by pressing a button. It is included in the touch screen test item. The calibration mark and calibration parameters are saved in the AT24C02 flash. If necessary, read from the flash. The calibration process is as shown below:
   
   B. C51 test program touch screen calibration instructions The C51 touch screen calibration needs to execute the Touch_Adjust test item (only available in the STC12C5A60S2 test program), as shown below:
   
   After the touch calibration is passed, you need to save the calibration parameters displayed on the screen in the touch.c file, as shown below
   

Common software

This set of test examples requires the display of Chinese and English, symbols and pictures, so the modulo software is used. There are two types of modulo software: Image2Lcd and PCtoLCD2002. Here is only the setting of the modulo software for the test program. The PCtoLCD2002 modulo software settings are as follows:
Dot matrix format select Dark code the modulo mode select the progressive mode Take the model to choose the direction (high position first) Output number system selects hexadecimal number Custom format selection C51 format The specific setting method is as follows: http://www.lcdwiki.com/Chinese_and_English_display_modulo_settings Image2Lcd modulo software settings are shown below:

The Image2Lcd software needs to be set to horizontal, left to right, top to bottom, and low position to the front scan mode.

www.surenoo.com

References

• Surenoo Tech: Professional LCD Module Supplier Since 2005

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>