puhui T-937 Lead Free Reflow Oven User Manual

June 4, 2024
puhui

puhui T-937 Lead Free Reflow Oven

puhui T-937 Lead Free Reflow Oven
product

Parameters

Soldering area 306mmX322mm
Dimension 404mmX372mmX280mm
N. Weight 15.5kg
Voltage/Frequency AC220 ~ 230V/ 50~ 60Hz
Power rating 2300W
Cycle time 2~ 16 min
Temp rage Room temp ~ 350 “C

Configuration

Name Q’ty
T-937 lead-free reflow oven 1
Power line 1
fuse 1
CD 1
COM communication line 1

Main parts

Mainbodypuhui T-937 Lead Free Reflow Oven fig 1

  1. Operation panel
  2. Drawer
  3. Switch
  4. Plug base

Operation Panelpuhui T-937 Lead Free Reflow Oven fig
2

  1. Indicator light
  2. Display
  3. Key

Otherspuhui T-937 Lead Free Reflow Oven fig 3

  1. Exhaust
  2. COM

Installation

  1. Please put this reflow oven on the flat tabletop.
  2. Please put this reflow oven in safe environment, not flammable or combustible.
  3. Please leave 20mm around the machine, for heat dissipation.
  4. The machine must be connected with Earth wire.

Software Interface

Main Interfacepuhui T-937 Lead Free Reflow Oven fig
4

  1. Menu bar
  2. Shortcut bar
  3. client drawing area
  4. display setting area
  5. operation tip area
  6. T-t da ta wave
  7. control point
  8. control point line
  9. toolbar

The client drawing areapuhui T-937 Lead Free Reflow Oven fig
5

  1. temp axis
  2. cursor
  3. solder paste character wave
  4. coordinate display
  5. time axis
  6. effected wave
  7. wave graph

Shortcut barpuhui T-937 Lead Free Reflow Oven fig 6

  1. check machine memory wave
  2. run the machine memory wave
  3. solder paste brand
  4. solder paste model
  5. re-set viewport
  6. set cycle time
  7. current oven temp

Display setting areapuhui T-937 Lead Free Reflow Oven fig
7

  1. control points moving direction
  2. partially/completely move the control point
  3. change to set control point cursor
  4. save pic in client drawing area
  5. show topics
  6. wave line width
  7. paste
  8. smooth wave
  9. temp setting range

Manual Instruction

  1. Install RS232 driver
    Please see the CD-“usb driverV3.1”

  2. Install the software
    Open the CD, find the “T-937 回流焊控制系统.exe(T-937 Reflow Soldering Control System.exe)”, double-click, start to install.

  3. Software Operation

  4. Viewport setting
    After open the software, you will see the ”viewport setting”, in order to get good visual effect, please set the time parameter of viewport to ”reflow target time +10S”, set the temp parameter to “target peak temp+20℃, press “confirm”

  5. Operation with PC
    Please use the communication line to connect with computer.
    Open T-937 software, press menu bar-other function-system parameter, open the setting window. Select “USB-SERIAL CH340 (COM**)”, press “confirm” and return to main interface, you will see like this in the shortcut bar, then press F2 on the reflow oven, T-937 reflow oven LCD displayer will show “connected with PC”, also you will see in the software, connect successfully.

  6. Make the wave

  7. Set the solder paste character click “Display setting area -7 paste”, the wave will display in the client drawing area. Click “display setting area – paste user”, it will show the user-defined paste character, or the the paste character from the paste database. Use the paste database from software
    Select the paste model from the shortcut bar, the paste wave will display in client drawing area.
    User define paste data
    Click “others” –“ user defined solder paste”, it will show “user defined paste window”, fill in the paste parameters you use, click “save”. This wave will display in the client draw area.

  8. Set up the wave
    open the wave from machine memory
    Click “menu” – “open recipe”, select the wave you want to use.
    Tips:this machine is with 8 waves inside, if these 8 waves can not match your solder paste, please adjust the wave in order to match with your solder paste, get good reflow effect.
    Set up wave
    Under “place control points state”, the mouse cursor will change to (click the right mouse button to switch “place/check control points state”), then click in the client draw area, place the control point, set up new wave.

  9. Adjust the wave
    Under “check control points state”, double click the client draw area, it will show many control
    also you can use to adjust the wave in different direction, it can change the wave fastly. Tips:the paste character wave show the theoretical wave, in fact, due to the influence of various factors such as heat conduction rate, so please adjust the wave according to the actually reflow effect, in order to get perfect soldering effect.

  10. Preview the wave
    Please click “operation” – “profile preview” to check the wave which the user made if it meets request, if the temps are over the “T Limit” (in the display setting area, No.9) , this software will set these temps to 45℃ automatically.

  11. Set the wave heating time
    Please set the heating time in the shortcut bar –

  12. Save the wave
    Click “menu”-“save recipe”, fill in the wave name, press “save”.

  13. Manager the wave
    Click “database management”–“recipe management” , will display the wave management window.

  14. Send the wave to T-937 reflow oven
    T- 937reflow oven has 8 file areas for saving the waves, if not connect with PC, T-937 reflow oven can perform the wave independently.
    After making the wave in the computer side, click “operation” –“send to device” , select the profile No. to send.

  15. View the waves in machine
    Click the “view” , select the profile No, this wave will display in the client drawing area, then you can adjust the wave here, and save it.

  16. Run the wave in machine
    Click the “run” in the shortcut bar, select the profile No, it will show wave running window, start soldering.

Independent Operation

Panelpuhui T-937 Lead Free Reflow Oven fig 14

InterfaceElectrolux-EMM25D59EB-25L-Ultimate-Taste-300-Freestanding-
Microwave-Oven-fig-12puhui
T-937 Lead Free Reflow Oven fig 16

The main interfacepuhui T-937 Lead Free Reflow Oven fig
17

  1. wave number
  2. operation tips(F1/select next wave ; F3/select last wave; F2:switch last/next 8 mins wave)

puhui T-937 Lead Free Reflow Oven fig 18

  1. Set temp
  2. set time(–:– is untimed model)
  3. operation tips(F1/ up,F2/ down,F3/switch set temp or set time
  4. current temp
  5. current running time

Operation

  1. Enter the software interface
    Press F1, will come to the independent operation interface

  2. Select the wave
    Under the independent operation interface, press F2 to select wave, press F1 and F3 to select the wave you need, then press “return key” to independent operation interface.

  3. Run the wave
    Under the independent operation interface, press F1, it will run the wave you selected.

  4. Thermostatic timer function
    Under the independent operation interface, press F3, start the thermostatic timer function. Thermostatic timer function means the machine can keep thermostatic temp if you set time, once time over, the machine stop heating.
    Press F3 change “set temp”/”set time”, press F1/F2 to adjust the numerical value, the time is–:– is untimed model, means the machine is keeping thermostatic heating, not stop automatically.

  5. Change language
    Under the main interface, press F3 to change the language.

Attention

  1. If not use this machine for long time, please unplug the power line plug.
  2. The machine should be connected to the exhaust passage within the outdoor ventilation or exhaust recovery, prevent solder paste volatiles poisoning.
  3. This machine is with strict protective insulation materials, please don’t open the machine casually.

Warranty

The warranty for mainbody is one year, for parts is three months, provide lifetime technical guide.

Declaration
If there is inconsistency between this user manual and the actual product, the actual product shall govern.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals