KASK HP Plus AS Helmet User Manual
- June 9, 2024
- KASK
Table of Contents
- KASK HP Plus AS Helmet
- Product Information
- Product Usage Instructions
- DATE OF MANUFACTURE
- EXPLANATORY MARKING DIAGRAM
- SAFETY HELMET FOR INDUSTRIAL USE
- INSTRUCTIONS
- ADJUSTMENTS
- PRODUCT OBSOLESCENCE:
- GUARANTEE
- ADDITIONAL REQUIREMENTS ACCORDING TO EN standards
- DECLARATION OF CONFORMITY
- HP PLUS NOMENCLATURE
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KASK HP Plus AS Helmet
Product Information
This device meets the additional requirements according to EN Standards and
complies with the EU Declaration of Conformity. To obtain a copy of the
declaration, visit the website www.kask.com.
The device is labeled as HP Plus Nomenclature with the following numbers:
819771032564.
Product Usage Instructions
- Ensure that the device is compatible with the intended use and meets all applicable safety requirements.
- Refer to the user manual for instructions on how to set up and use the device.
- When setting up, carefully follow all instructions and precautions to prevent injury or damage to the device.
- Before using the device, ensure that it is in good condition and free from damage.
- Use the device only for its intended purpose and within its specified limits.
- Do not modify or attempt to repair the device unless authorized to do so by the manufacturer.
- Keep the device away from children and pets.
- When not in use, store the device in a cool, dry place away from direct sunlight.
- If you experience any problems with the device, refer to the troubleshooting section of the user manual or contact the manufacturer for assistance.
By following these usage instructions, you can safely and effectively use the device for its intended purpose.
DATE OF MANUFACTURE
EXPLANATORY MARKING DIAGRAM
SAFETY HELMET FOR INDUSTRIAL USE
For adequate protection, this helmet has to fit or to be adjusted to the size
of the user’s head. The helmet is made to absorb the energy of a blow by
partial destruction or damage, and even though such damage may not be readily
apparent, any helmet subjected to severe impact should be replaced. The
attention of the user is also drawn to the damage of moditying or removing any
of the original
component parts of the helmet, other than as recommended by the helmet
manutacturer. Helmets should not be adapted for the purpose of fitting
attachments in any way not recommended by the helmet manufacturer. Do not
apply paint, solvents, adhesives or self-adhesive labels, except in accordance
with instructions from the helmet manufacturer. For cleaning, maintenance or
disinfection, use only substances no adverse effect on the helmet and are not
known to be likely to have any adverse eftect upon that h. the wearer, when
applied in accordance with the manufacturer’s instructions and information.
-
DANGER! Intended use of this helmet involves activities that are extremely dangerous. FAILURE TO HEED AND FOLLOW THESE INSTRUCTIONS AND ANY OF THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR EVEN ATH.
-
WARNING: Carefully read and understand these instructions. Use this helmet exclusively for the activities for which it is certified (see Labeling) and in strict accordance with AS/NZS 1801
-
WARNING: Improper use of this helmet can cause serious or fatal injury. If the instructions are not followed correctly, the level of protection offered by the helmet can be significantly reduced. Inspect the helmet before each use far any signs of visible damage. DO NOT USE HELMET IF THERE IS ANY SUSPICION OF ITS CONDITION OR AFTER A MAJOR IMPACT.
-
WARNING: It is mandatory that the user becomes knowledgeable about all teatures of the helmet, its capabilities and limitations, and gets specitic instructions andlor training from a competent and responsible person in the proper use of the helmet.
-
WARNING: USERS OF THE HELMET ARE FULLY RESPONSIBLE FOR THEIR ACTIONS AND ASSUME ALL RISKS
FOR THEIR DECISIONS. KASK S.p.A., its atiliates, subsidiaries, importers, distributors and dealers will accept no responsibility in the event of an accident leading to injury or even death and shall not be liable for any injury, death, loSs, or damage resulting from improper use of this helmet. -
WARNING: SPECIFIC TRAINING IS ESSENTIAL BEFORE USE. Read this notice carefully and keep all instructions and intormation on the proper use and application ot the product(s). Many types of misuse exist and it is impossible to enumerate or even imagine all ot them. Contact KASK it you have any doubt or ditticulty understanding these instructions. Activities at height are dangerous and may lead to severe injury or even death. Gaining adequate training in appropriate techniques and methods of protection is your own responsibility. YOu personally assume all risKs and responsibilities tor all damage, injury or death which may occur during or following incorrect use of our products in any manner whatsoever. It you are not able, or not in a position to
assume this responsibility or to take this risk, do not use this equipment. -
USE: This product must only be used by competent and responsible persons; or those placed under the direct and visual supervision of a competent a responsible person. Personal protective equipment (PPE) IS to be used only on or with energy-absorbing systems (tor example dynamic ropes, energy absorbers etc.). Check that this product is compatible with the other components of your equipment, see the instructions specific to the products. 1o prolong the life of this product, take care when transporting and using it. Avoid impacts or contact with abrasive sutaceS or. sharp edoes.
-
NOTE: You are responsible for your own actions and decisions. Betore using this helmet, you must:
read and understand all instructions tor use;
get specific training in its proper use
become acquainted with its capabilities and limitations;
understand and accept the risks involved.
Failure to heed any of these warnings may result in severe injury or death. The manutacturer and/or distributor will accept no responsibility in the event of accidents leading to injury or even death due to improper use to the helmet. This helmet is constructed to absorb impact by partially distributing the shock or by damaging its
essential components. Activities at height present a risk or serious head injury. Wearing helmet can significantly reduce this risk, but cannot entirely eliminate it. His helmet should be used exclusively for the activities tor which it is certified (see labeling). Ihis helmet has been approved tor industrial head protection. -
WARNING: This helmet cannot always protect the user trom injury. >pecitically, keep in mind that no helmet can protect the head from the shock generated by violent impact. Following Violent impact, even if no damage is Visible, tne helmet should be replaced, In that itS capacity to absorb Turtner impact could be impaired.
-
WARNING: Your helmet can be damaged from improper care: do not Sit on it, pack it too tightly, drop it, allow to contact sharp or pointed objects, etc. Do not expose your helmet to high temperatures, tor example by leaving it inside a vehicle in direct sunlight.
INSTRUCTIONS
- As a protective measure, this helmet must be worn at all times during work activity. For adequate protection, it is important that the helmet be sized correctly and fit the head properly to ofter optimum comtort and satety, Ihe helmet should be adjusted to fit the user, ex., the straps should be positioned so that they do not cover the ears, the buckle should be kept away trom the jawbone, and the straps and buckle should both be adusted so that they are comfortable and secure, Atter properly buckling and adjusting the strap, always check that the helmet is not excessively tight; nor should it move freely back and forth. Verify that the helmet is well seated and centered on the head (see Fig. 1). The better a helmet is adjusted (minimal movement front to back or side-to-side), the better protection it can provide.
HP PLUS NOMENCLATURE: 1. Shell; 2. Headband (not removable); 3. Size adjustment system; 4. Chinstrap; 6. Lateral retractor, 6. Buckle; /. Lamp clip;8. Side slot for hearing protection adapter, 9. Side slot to insert visor adapter; 10. Marking Label.
ADJUSTMENTS
- Wear the helmet and adapt the size by turning the rear wheel (clockwise to tighten the size and counter-clockwise to enlarge it) or simply (only for models equipped) by drawing the two quick-closing elements to obtain the desired tension (Fig. 2).
- Position the size adjustment system in the nuchal area as shown (Fig. 3), tilting it and adjusting it in height. For versions equipped with a chin strap, tasten it by inserting one buckle strap into the other until it clicks into place (Fig. 4a). Pull the chin strap to check that the buckle is locked (Fig. 5). Adjust the length of the chin-strap to ftirmly secure the helmet on your head. Ihe rubber ring must be positioned on end of the tape to prevent it dangling. Adjust the lateral retractor of the chin strap by sliding it along the straps until you tind the desired position below the ear (ig. 6). Jo remove the helmet from the head, open the chin-strap by Simuitaneously pressing the buttons on each side of the buckle (hig.46). Use of the rear sliders (only for versions provided): it is possible to use the rear adjuster to prevent the lateral retractor trom being in uncomfortable positions, such as interterence with the ear or during the use of hearing protectors.
- SPARE PARTS: Changes, replacements and/or removals of one or any of the original components of the helmet are prohibited unless authorized by the manutacturer.
- Only use original KASK spare parts. The helmet should not be moditied to accommodate other accessories other than those described below. If necessary, contact your retailer or the manutacturer directly.
SPARE PARTS:
Changes, replacements and/or removals of one or any of the original components
of the helmet are prohibited unless authorized by the manutacturer. Only use
original KASK spare parts. Ihe helmet should not be moditied to accommodate
other accessories other than those described below. If necessary, contact your
retailer or the manutacturer directly.
ACCESSORIES:
Check with your retailer or manutacturer the actual availability of the
accessories. Follow the user manual supplied with them. Only use accessories
approved by the manutacturer
CLEANING:
Clean the helmet (and accessories) using only water, mild soap and a soft,
clean cloth, and let it air dry at room temperature. The internal padding can
be removed and washed by hand in cold water or in the washing machine (max.
30C/ 86° F). Never use chemical cleaning products or solvents.
WARNING:
Certain chemical products, especially solvents, can damage your helmet.
Protect your helmet trom exposure to chemicals.
STORAGE:
When not in use, it is preterable to store the helmet at a temperature between
5″C and 35″C (41°F to 95 F), protected trom direct sunlight and away trom
sources of hear. KASK recommends to store the helmet n its original packaging.
MODIFICATIONS AND REPAIRS:
Do not apply adhesives. solvents. stickers. or paint that does not comply with
the manutacturers specifications. Do not modity the helmet in any way without
authorization from KASK. An unauthorized modification can reduce the products
effectiveness and invalidate its certification. Repairs made outside ot KASK
tacilities are prohibited.
TRANSPORT:
Given the type oft device (helmet), no particular instructions are necessary
for its transport. During transport do not pack the helmet too tightly.
CHECK:
Before using the helmet check its integrity in all ts parts. Following a
violent impact even if the damage is not visible replace the helmet, as it may
have exhausted its ability to absorb turther shocks and provide the expected
protection.
REVISION:
In addition to the normal visual check before each use, a competent person
must pertorm a thorough examination at least annually. Ihe registration of the
controls must be made on a control sheet downloadable trom the manufacturer’s
website www.kask-satety.com. Do not remove labels or markings and check their
legibility. If you tind cuts, abrasions or any other damage, before reusing
the helmet contact the manutacturer to have it examines.
LIFE:
The life span of the helmet depends on the occurrence of various degenerative
factors, including sudden changes in temperature, exposure to sunlight,
intense use. The helmet must be checked periodically, and in any case before
each use, to ascertain the presence of damage such as cracks, detachments,
deformations, peeling which are elements that reveal the deterioration ot the
helmet. The helmets which have shuttered significant impacts must be replaced
even if they do not show evident signs of damage. Ihe maximum shelt life of
this product is 10 years from the date of manufacture. After this period, the
helmet must be discarded because the protection decreases due to the aging.
Ihe production date is shown inside the helmet.
ATTENTION:
In extreme cases, the litetime can be reduced to one single use through
exposure to any of the tollowing: chemicals, extreme temperatures, sharp
edges, major tall or load, etc. Cracks, detached parts, warping, talking, and
changes in color are significant elements for verifying the helmet’s state ot
deterioration; in any case, we advise replacing it atter 5 years of use,
because over time its protection decreases.
WHEN TO RETIRE YOUR EQUIPMENT:
immediately retire any equipment if:
it fails to pass inspection (inspection betore and during use and the periodic
in-depth inspection);
it has been subjected to a major tall or load;
you do not know its full usage history,
it is at least 10 years old;
you have any doubt as to its integrity
Destroy retired equipment to prevent further use.
PRODUCT OBSOLESCENCE:
There are many reasons why a product may be judged obsolete and retired before the end of its litetime. Examples include changes in applicable standards, regulations, or legislation; development of new techniques, incompatibility with other equipment, etc.
GUARANTEE
This product is guaranteed for 3 years against any defects in materials or manutacturing. Exclusions from the guarantee: normal wear and tear, oxidation, modifications or alterations, incorrect storage, poor maintenance, damage due to accidents and/or negligence, or to improper and incorrect usage. KASK is not responsible for the consequences, direct, indirect or accidental, or any other type of damage betalling or resulting trom the use of its products.
LABELING:
Information contained on the inside of the helmet, printed on a label, should
not be removed for any reason.
ADDITIONAL REQUIREMENTS ACCORDING TO EN standards
PURPOSE OF THIS PPE
This device has been designed to offer protection of the users head against
the risk of objects talling from above and consequent brain injuries and skull
fractures. Ihis helmet is constructed in such a way as to absorb the energy of
an impact through the partial distribution or damage of the essential
components. Ihis helmet must be used only and exclusively tor the activty tor
which it was certified (see marking) his high pertormance helmet for industry
has been CE approved following to European Regulation EN 14052:2012. This
helmet complies with the retention standards of the European Regulation EN
14052:2012 when the chin strap is worn and adjusted as per our instruction
manual. The helmet also meets the additional EN 12492:2012:
4.2.1.2-4.2.1.3-4.2.1.4 tront/back/side shock protection and EN397:2012 5.2.4
Side deformation- 5.1.1 – 5.1.2 impact and penetrations standard requirements.
The Certification procedure was carried out by the notitied body no.0426,
Italcert Viale Sarca, 336 20126 Milan – Italy.
WARNING:
This helmet cannot always protect the user from injury. Specifically, one
should keep in mind that no helmet can protect the head trom the shock
generated by a violent impact. Following a violent impact even it thee damage
is not visible, the helmet should be replaced, as it may have exhausted its
ability to absorb further shocks and provide the expected protection. The
helmet object of this manual is a type ll Personal Protection Device and as
such was subjected to EU-type Certification procedure with application of the
requirements laid down in Annex V ot the EU Regulation 2016/425. Ihe device is
subject to the control procedure in accordance with Annex Vll of the
aforementioned Regulation. The veritication activities are assigned to the
Notified Body 0426.
DECLARATION OF CONFORMITY
To get a copy of the EU Declaration of Conformity for this device, visit the website www.kask.com.
HP PLUS NOMENCLATURE
KASK S.p.A.
24060 Chiuduno, BG
Via Firenze, 5 – Italy
t. +39 035 4427497
info@kask.com
www.kask.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>