Coolife H8201 Night Vision Trail Camera User Guide

: June 9, 2024
: COOLIFE

Table of Contents

Introduction
Preparing the Camera
Basic Operation
Setup Menu and Functions
FAQ
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

H8201 Night Vision Trail Camera
User Guide Coolife H8201 Night Vision Trail Camera

Introduction

1.1.After sales service
Choose us! We provide you with the best products and services, and always focuses on professional brands.
We are committed to sincere and thoughtful service to ensure customer satisfaction. If you have any questions or problems about our products, please be free to contact us by email: support@coolife.site
We will reply you within 24 hours and provide you with a 100% perfect solution.

If you want to learn more about the following information, you can go to our website (www.coolifeeu.com)to view

Beginner tutorial
Download the manuals for different models
Get new product information
FAQ (Frequently Asked Questions and Answers)
Make suggestions or complaints about the products
Product operation video

1.2. Trail camera working principle
The working principle of the trail camera is that the infrared sensor triggers to take photos. In fact, when the heating body (animal, etc.) enters the infrared sensing area of the trail camera, the sensing module of the trail camera will start the camera to complete the capture, thereby obtaining photos and videos. If the heating body (animal, etc.) leaves the infrared sensing area, the trail camera is in a dormant standby state, for example, the trail camera starts to capture again when it enters the infrared sensing area again.
Application

Trail camera for hunting
Animal or event observation Motion-triggered security camera, for home, office and community
All other indoor/outdoor surveillance where invasion evidence needed

1.3. Warning

The H8201 hunting camera uses IR LEDs with a wavelength of 850nm, which emits a faint red light at night. But most animals cannot see this infrared light and will not interfere with the animals.
When the ambient light source is unstable, the filter inside the camera will be triggered to work, and then there will be a clicking sound accompanied by screen flickering, which is normal.
It is recommended to use high-performance alkaline batteries, which can prolong the use time of the camera. It is not recommended to use a 1.2V rechargeable battery, because the working voltage of the hunting camera is 1.5V. If the battery voltage is insufficient, it will not properly work, and the battery may be exhausted after working for few hours (the camera will show that the battery is low).
When using the hunting camera for the first time, please format the memory card before using.
When installing the battery, please make sure to install the battery normally, if the battery is installed upside down, it will cause the camera to short circuit and burn out. Please note that the camera is not protected by the short circuit!
When using the product for the first time, please remove the layer of protective film on the lens and on the sensor of the product.
Do not damage the surface of the product sensor, if there is any scratch or damage, it will affect the normal triggering of the camera.
Field installation: please make sure that the buckle of the camera and the bottom DC plug are all closed and sealed, otherwise the camera could be damaged in case of rain.
Do not use the mini USB data cable to charge the camera or charge the rechargeable battery, it will seriously damage the camera.
Please keep the camera lens and infrared sensing windows clean. If dirty, clean with the soft glasses cloth.
For keeping the good waterproof and dustproof properties, please keep the battery compartment sealing ring clean.
Do not touch the LCD display screen, camera lens, infrared sensing windows and IR led glasses with hands or any sharp objects.
In case of low battery charge, please replace all the batteries on time to avoid leakage of the electrolyte that could damage the camera.

If you want to know more information, please go to our website(www.coolifeeu.com) to view or directly scan the QR code to view.

https://coolifeeu.com/

Parts Of The Camera

|
---|---
1.Display Screen| 11.Micro SD Card Slot
---|---
2.Up/Video Button| 12.AV Jack
3.Shot Button| 13.USB Jack
4.Right Button| 14.OFF-TEST-ON
5.OK Button| Mode Button
6.Speaker| 15.Infrared LEDs
7.Menu Button| 16.Day Camera
8.Left Button| 17.Front Motion Sensor
9.Playback Button| 18.Side Motion Sensor
10.Down/Photo Button| 19.Status Indicator
| 20.Night Camera

1.5. Trail camera operation process

Coolife H8201 Night Vision Trail Camera - Introduction

1.6. Explanation of camera screen pictures Coolife H8201 Night Vision
Trail Camera - Introduction 2

Image sensor	8 Megapixel tmd 2 MP NIR-Sensor aufStemenlichtniveau
Photo resolution	32MP/20/s/fP/16MP/12MP/8MP/5MP
Video resolution	3840×2160/101ps; 2688×1520/20ts

Preparing the Camera

2.1. Opening and closing the camera
Operating buttons, connections and batteries are located inside the Wildlife Camera. A fixing for a padlock is provided between the two locking brackets, allowing the camera to be securely locked.

Coolife H8201 Night Vision Trail Camera - locking

2.2. Inserting the batteries
Open the camera as described in （2.1.） to insert the batteries. The battery compartment is housed in the right, rear part of the camera.
Now open the protective cover of the battery compartment by pulling the clamping closure at the top slightly inwards before lifting off the cover.（The buckle can be opened with the help of a small tool）

Insert 8 x 1.5V LR6/AA high quality alkaline batteries. Make sure to insert each battery with correct polarity.
Note:

It is not recommended to use 1.2V rechargeable batteries, because it is not enough to support the normal operation of the camera. We recommend high-performance alkaline batteries (not supplied).
Never install different types of batteries or new and old batteries in the product at the same time.
Anytime you load or unload batteries, make sure that the camera is OFF.
An alarm is sounded if the battery charge is too low.
Most batteries will lose their activity when working at low temperatures, causing a potential camera failure. Put the camera indoors and it will return to work normally.

2.3. Inserting the memory card
A memory card must have been inserted in order to save photos (in .jpg format) and videos(in .AVI format). Insert a TF memory card in the memory card compartment before switching on the camera.

Switch OFF the camera. Insert the memory card as shown in the adjacent illustration. Push the memory card into compartment until it clicks into place.
To remove the memory card push card in again until it is partly ejected

Note:

Please format the memory card if it is used for the first time or if it has been used with other cameras before.
Suggest to use at least class 10 or above high.
Be sure the power switch is OFF before inserting or removing SD cards or batteries.
A Micro SD/TF memory card must be inserted into the memory card slot in order to save photos and videos.
After using the memory card many times, its performance will be reduced. If the memory card performance decreases, you need to buy a new memory card.
Don’t remove the card, don’t turn off the power while formatting or reading or saving because data could be damaged.
If the capacity of the memory card is full, the camera will stop recording automatically and the LEDs will be off. Turn on the Endless Capture function if you want to keep on saving data: in this case the newest data will replace the oldest.
Do not insert the memory card forcibly. Please refer to the marking on the camera. Press the edge of the card gently to pop up the TF card.

2.4. External power supply
Optionally, you can connect an external 6V DC power source with at least 1.5 A to the ‘DC In’ jack at the bottom of the camera. The power connector is a 3.5×1.35 mm coaxial DC power plug with positive ‘tip’ (inside pin) polarity. Leave internal batteries in the camera during use.
Note:

Rechargeable batteries cannot be recharged in the camera using an external power supply.
It is not recommended to use a universal external power adapter, if the voltage is adjusted to inaccurate, you risk to burn the camera.
When using an external power source, please leave four or eight new batteries( Avoid External Power Suspension).

2.5. Assembly with strap
Use the securing strap supplied to attach the Wildlife Camera to a tree or another object. The illustrations below demonstrate how to fasten the securing strap. Coolife H8201 Night Vision Trail Camera - strap

Position the Wildlife Camera as desired and pull the loose end of the securing strap tight until the camera is firmly secured. To release the securing strap again, pull at the tab of the securing strap.

2.6. Using the wall mount/bracket
Using the supplied wall mount, the camera can be securely attached to walls or ceilings. Prior to installing the wall mount ensure that all existing bolts are securely tightened.

1/4“Tripod bolt
Counter screw/Lock nut
Pivot bolt
Drilled holes
Hexagonal screw
Plastic expansion tube/Wall plugs
Long screw of metal bracket

Required tools

Drill
6 mm masonry/concrete drill bit
Phillips head screwdriver
Note:
Ensure that there are no electric lines, water, or heating pipes installed at the proposed drilling location!
The supplied wall plugs are only suitable for mounting on concrete or stone. Before starting the installation, please check your installation location carefully for its suitability for the plugs. The assembly material used must be suitable for the respective location. If in doubt, consult a professional.

Steps

Mark the drill holes by holding the foot of the wall bracket at the desired mounting location and marking the hole positions.
Use a drill with a6 mm drill bit to drill the required holes and insert the plugs and insert the wall plugs flush with the wall.
Screw the wall bracket to the wall using the supplied screws.
Mount the camera on the tripod screw and screw the camera a little way on (about three turns).
Turn the camera in the desired direction and lock it with the lock nut.
To move the camera into its final position, undo the two pivot bolts a little, position the camera, and fix the position by tightening the two pivot bolts through the hexagonal screw.

2.7. Install the camera properly

Coolife H8201 Night Vision Trail Camera - Preparing

Please refer to the above installation diagram to determine the correct installation angle, install the hunting camera as horizontally as possible, and do not install it downwards, which will reduce the capture range of the camera and the shooting angle.
Note:

The correct installation distance should be at least one meter away from the subject, otherwise, it is easy to be vague.
Please make sure to install the hunting camera horizontally, otherwise, it may reduce the detection range of the camera.
The installation height is determined by the size of the shooting target or the distance, such as a small hedgehog, the shooting distance should be as short as possible, and the installation height should be as low as possible).
There should be no obvious obstructions (such as branches and leaves) in the front of the lens, and try to keep it as open as possible.
Try to confirm that there is no strong backlight at the front of the lens, otherwise, the quality of the photos and videos taken will be seriously reduced, and noise and blurring will occur.

2.8. How to use the cable
Use a mini usb cable to connect (when viewing files)
You need to use the camera’s mini usb cable to connect the camera body and the computer.

Coolife H8201 Night Vision Trail Camera - cable

Connect to TV (while viewing files)
A dedicated TV cable is required to connect the image output port of thecamera body to the TV.

Coolife H8201 Night Vision Trail Camera - TV

2.8.1. The camera can transfer the video signal to an external monitor or a television. Please follow the below instructions to operate

Connect the camera to the TV via provided AV cable.
Turn on the TV and set it to AV mode.
Turn on the camera, switch the Mode Button to“Test”.
Once connection is successful,the camera will enter playback mode and the screen turn black. The image will show on the TV.

Basic Operation

3.1. Switch to “ON”,”TEST” and “OFF” mode
When the camera is in the “TEST” mode
The camera can set parameters, check the camera, manually shoot and view photos and videos, etc.
When the camera switch to “ON”
After having switched on the camera, the screen will display 15 seconds countdown. Then the LEDs and screen will be off. The camera begins to operate independently and enter in the standby mode.
If wild animals enter the detection range of the motion sensors, the camera will be activated and detect the motion trail.
If wild animals keep on moving in the detection zone of the sensor, the camera will take photos or record video automatically.
When wild animals leave the detection zone of the sensors, the camera will be deactivated and turn back in standby mode.
When the camera switch to “OFF” mode The camera is completely turned off.

3.2. Adjust the best way of installation in Test mode
In test mode, you can work out the optimum exposure angle and the range of the motion sensors.
During alignment, consider whether the use of the side motion sensors may be useful for attaining the desired observation results. You can activate/deactivate the side motion sensors using the described menu.

https://coolifeeu.com/

4. Setup Menu and Functions
Mode
Set the working mode. In capture mode, the camera just takes pictures.
In Video mode, the camera just record video. In capture&video mode, the camera will take a photo first, then start to record video.
Options：【Photo】/【Video】/【Photo&Video】.
Day Photo Resolution
Set the still image resolution.
Options ：【 32MP(6480x480P) 】 / 【 20MP(5200x3900P) 】/【 16MP(4608x3456P) 】 / 【 12MP(4000x3000P) 】 /【8MP(3264x2448P) 】/【5MP(2592x1944P) 】/【3MP(2048x1536P) 】 /【1MP(1280x960P) 】.
Night Photo Resolution
Set the still image resolution.
Options：2MP【(1920x1080P) 】/1MP【1280x720P) 】
Photo Series
Set the photo number of continuous shooting. In photo mode, the camera will take photos continuously.
Options：【1 photo】/【2 photos in series】/【3 photos in series】/【10 photos in series】.

FAQ

For more detailed product questions and answers, please check through our official website (www.coolifeeu.com ), which contains a variety of very detailed questions and answers.
You can directly enter the website to view by scanning the following QR code

https://coolifeeu.com/

C&E Connection E-Commerce (DE) GmbH Zum Linnegraben 20, 65933, Frankfurt am Main,Germany
info@ce-connection.de
Made in China
Manufacturer: GO DIGITAL LTD. Address: 4th Building, Tianan Digital City, Huangge Road, Longgang District, Shenzhen.