Chicco Digital Bottle Warmer and Sterilizer Owner’s Manual

June 9, 2024
chicco

Digital Bottle Warmer and Sterilizer
Owner’s ManualChicco Digital Bottle Warmer and
Sterilizer

Read all instructions BEFORE assembly and USE of product.KEEP INSTRUCTIONS FOR FUTURE USE.

Digital Bottle Warmer and Sterilizer

WARNING
WHEN USING THIS ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:

BURN HAZARD
To avoid risk of burns:

  • Bottle warmer components and water temperature can be very hot. Avoid direct contact with water and steam. Handle with care.

  • Do not touch surfaces that may be hot.
    Wait until all parts of the unit have cooled before touching them.

  • Bottles and food jars will be hot; remove with care.

  • Before serving, be sure food is at a safe temperature.

  • To avoid direct contact with hot water, use support tray when warming food containers or small bottles.

  • Extreme caution must be used when moving the bottle warmer with hot liquid in it.

CAUTION

  • NEVER use without water.
  • This is NOT a toy. Keep out of reach of children.
  • Adult supervision required.
  • Close supervision is necessary when any appliance is used near children.
  • For household use ONLY – Do NOT use outdoors.
  • Only use appliance for intended use, do not modify or alter warmer.
  • Do not use accessories, spare parts, or any components not supplied or approved by Chicco as they may cause injuries or damage.
  • Do NOT use with any bottle or food container that is not intended to be heated.
  • Do not place on or near a hot gas or electric burner, or in a heated oven.

CAUTION

  • Not for space heating purposes.
  • Do NOT let cord hang over edge of table or counter or touch hot surfaces.
  • NEVER use an extension cord.
  • Before serving, unplug cord from wall outlet. Do not leave cord within child’s reach.
  • Always attach plug to bottle warmer first, then plug cord into the wall outlet. Always turn off the bottle warmer before removing the plug from the wall outlet.
  • This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, a polarized electrical outlet will only allow the plug to be  inserted one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in  any way.
  • Remove plug from outlet when the appliance is not in use, before putting on or taking off parts, and before cleaning.  Allow to cool before handling.
  • Inspect carefully before each use. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any  manner. If bottle warmer is faulty and/or not working correctly, switch it off immediately and unplug it from the wall outlet.
  • To protect against electrical shock do not immerse cord, plugs, or bottle warmer in water or other liquid.
  • Do NOT use if the bottle warmer, plug, or cord accidentally falls into water or becomes submerged.

PARTS LIST

Chicco Digital Bottle Warmer and Sterilizer - lid

CONTROL PANEL

Chicco Digital Bottle Warmer and Sterilizer - PANEL

SETUP – ADD WATER TO TANK

Using the chart below, determine the level of water that is needed for heating. Content level is the actual amount of liquid inside the bottle or milk bag being warmed. It is  NOT the size or capacity of the bottle.
Note: Warming cycle times may vary based on starting temperature, bottle size and contents. Use the chart below as a starting point. Warming cycle time may need to be  adjusted to reach the desired temperature.

Chicco Digital Bottle Warmer and Sterilizer - TANK

Make sure the Bottle Warmer is unplugged and placed on a flat, stable, heat resistant surface.
Pour water directly into the Bottle Warmer Tank up to the correct level (LEVEL 1 or LEVEL 2).
Chicco Duo is a wide neck hybrid baby bottle – glass inside & plastic outside. Select the Wide Neck Plastic Bottle setting for warming.

SETUP – POWER ON

Plug the cord into the back of the Bottle Warmer Tank and then plug it into the outlet. It will beep once.
Touch the START/STOP button.
The icons on the Control Panel will blink indicating that a cycle is ready to be selected.
Note: If no warming cycle is selected for three minutes the Warmer will beep and switch off automatically.

WARMING – STEP 1

Place bottle, milk bag, or food jar in the Bottle Warmer Tank.
For Bottles: Attach bottle ring and nipple before heating.
For Milk Bags: Make sure bag is sealed before heating. For Food Jars: Remove lid before heating.
Make sure the tank water does not reach the ring of the bottle, the seal of the milk bags, or the top of the food jar.
Note: Works with most bottle types.
If applicable, remove bottle venting systems when warming. Bottles made of various materials and construction will heat at different times.
Use the Support Tray for food jars and milk bags.

WARMING – STEP 2

Select the warming mode by touching the desired button. The icon will light up to confirm your selection.
Note: At any time during this process you can go back and change a previously selected setting by touching on that icon. The selection program will restart from that point.

WIDE NECK BOTTLE*
NARROW NECK BOTTLE
GLASS BOTTLE
MILK BAG
FOOD JAR

*Always select “WIDE NECK BOTTLES” when warming any silicone bottles.

WARMING CYCLE MEMORY
FUNCTION: The bottle warmer will save the previous settings to memory – Simply touch the START/STOP button to begin reheating using the previous settings.

WARMING – STEP 3

For Bottles: Select QUICK or STEADY mode.
For Milk Bags : Only STEADY mode is available – Milk Bags can NOT be warmed using QUICK mode. Skip to STEP 4.
For Jars: Skip to STEP 5.

QUICK Mode
STEADY Mode

WARMING – STEP 4

Touch “+” or “-“ to select the Bottle/Milk Bag content level in ounces.
Then touch the flashing  CONTENT LEVEL icon to confirm the amount.

Max. Allowable Content Bottles: 9 oz (290 ml)
Milk Bags: 6 oz (190 ml)
Note: The content level is the actual amount of liquid inside the bottle or milk bag to be warmed.

WARMING – STEP 5

Select the content temperature.
STARTING TEMP FREEZER : About 0°F (-18 °C)
STARTING TEMP REFRIGERATOR: About 40°F (4 °C)
STARTING TEMP ROOM: about 70°F (21 °C).
Note: Frozen setting unavailable for bottles. Room Temp. setting unavailable for Milk Bags.

WARMING – STEP 6 A default warming time will appear based on the previous selections. This time can be modified by touching “+” or “-“ to increase or decrease the warming time.
SILICONE BOTTLES take longer to heat. Always add 3 minutes to the default warming time.

WARMING – STEP 7

To start the warming cycle touch the START/STOP button.
The warmer will beep and the warming cycle will begin. The TIMER will show you the time remaining in the warming cycle.
The bottle warmer will turn off automatically once the warming cycle is complete.
Note: The warming cycle can be stopped at any time by simply touching the START/STOP button.
For information on
DELAYED START see page 15.

ONCE WARMING CYCLE IS COMPLETE

CAUTION: BOTTLE WARMER TANK WATER MAY BE HOT: CAREFULLY REMOVE THE BOTTLE, MILK BAG, OR FOOD JAR IMMEDIATELY AFTER  WARMING CYCLE IS COMPLETED.
ALWAYS CHECK THE TEMPERATURE OF THE CONTENTS BEFORE SERVING:
FOR FEEDING BOTTLES AND MILK BAGS:
Gently shake or stir the contents to ensure the temperature is even; check the temperature by squeezing a few drops onto the inside of your wrist.
FOR FOOD JARS:
Stir the contents of the jar to make sure the temperature is even; check the temperature by tasting.

  • For best results, allow the bottle warmer to cool completely (approx. 30 mins.) before starting a new warming cycle.
  • If you have twins, the Bottle Warmer can be used for two consecutive warming cycles by removing the plug from the wall outlet and carefully emptying the hot water and  replacing it with room temperature water. After plugging in the warmer and turning it back on, simply touch the START/STOP button to begin reheating using the previous settings stored in memory.
  • When warming Milk Bags and Jars from frozen, you may need to run a second cycle. The initial default warming time should be decreased as needed to prevent overheating during the second cycle.
  • If the jar contents are not warm enough, repeat warming cycle until desired temperature is reached. When repeating a cycle, check the temperature of contents at regular  intervals to avoid overheating. The initial default warming time can also be decreased as needed to prevent overheating during the second cycle.
  • When finished, remove the plug from the wall outlet. Do not leave cord within child’s reach. Allow the tank to cool down completely before pouring out the water. Dry the inside thoroughly.

DELAYED START

The warming cycle can be delayed for up to 60 mins. before beginning the cycle.
Before touching the START/STOP button (to start the warming cycle), touch the DELAYED START button. Adjust the time by pressing the “+” and “-“ buttons.
The delayed start can be set for 15 mins., 30 mins., 45 mins., and 60 mins.
Then touch the START/STOP button to start the warming cycle with a delay. The timer will countdown and then the cycle will begin.
The delay can be skipped at any point by touching the START/ STOP button again to run the cycle immediately.

STERILIZING – BEFORE FIRST USE
Before first use as a Sterilizer, run through a sterilizing cycle without anything except the support tray in the Bottle Warmer.

STERILIZING – STEP 1

Make sure Bottle Warmer is unplugged and placed on a flat, stable, heat resistant surface.
Always clean and rinse the bottles and accessories before placing them in the Bottle Warmer Tank.
Pour water directly into the Bottle Warmer Tank up to LEVEL 1.
Then place the Support Tray into the Bottle Warmer Tank.Chicco Digital
Bottle Warmer and Sterilizer - WATER1

STERILIZING – STEP 2

Chicco Digital Bottle Warmer and Sterilizer - WATER2

Plug the cord into the back of the Bottle Warmer Tank and then plug it into the outlet. It will beep once.
Touch the START/STOP button.
The icons on the Control Panel will blink indicating that a cycle is ready to be selected.
Note: If no warming cycle is selected for three minutes the Warmer will beep and switch off automatically.

STERILIZING – STEP 3

Place the bottle ring into the Support Tray.
Place the bottle UPSIDE DOWN into the Bottle Warmer Tank.
Then arrange the bottle cap, and nipple, as shown.

Place Sterilizer Lid onto the Bottle Warmer making sure the groove in the BACK of the Sterilizer Lid fits into the cutout in the Support Tray.
Make sure bottles and accessories do not prevent the lid from closing correctly.Chicco Digital Bottle Warmer and Sterilizer -
WATER4

STERILIZING – STEP 4

Touch the STERILIZE button. The icon will stop flashing to confirm your selection. Then touch the START/STOP button to begin the cycle. The TIMER will show you the time remaining in the sterilization cycle.

ONCE STERILIZING CYCLE IS COMPLETE

When the cycle is complete, a long audible beep will be heard and the Warmer will turn off automatically.
Always clean your hands thoroughly before touching the sanitized objects. Sanitized items will remain sterile inside the Warmer with the lid on for about 24 hours. If there is a  power outage during use of the Sterilizer the cycle must be restarted.
Allow the Warmer to cool completely before starting a new cycle. If complete, allow to cool then remove the plug from the wall outlet, pour out the water, and dry  thoroughly before storing in a cool dry place.

DESCALING

The normal use of the Bottle Warmer can cause the formation of scale residue on the heating plate. Excessive scale residue may cause incorrect operation and prevent proper  sanitation of the objects inserted in the appliance and/or cause permanent damage to the appliance.
The DESCALING icon will light up to indicate that you need to descale the Bottle Warmer.

To descale the Bottle Warmer, make sure it is unplugged and has cooled down completely.
Pour equal parts of water and vinegar directly into the Bottle Warmer Tank up to LEVEL 2. Let soak overnight. Do NOT run the unit while soaking. After it has soaked overnight, empty out the water and vinegar solution. Dry thoroughly with a soft cloth.
After descaling, press and hold the DESCALING icon/button for about 2 seconds until it resets the descaling function and switches off.

CARE AND MAINTENANCE

AFTER EACH USE: Remove the plug from the wall outlet. Do not leave cord within child’s reach. Allow the tank to cool down completely before pouring out the water. Dry the inside thoroughly.
CLEANING THE BOTTLE WARMER: Make sure the bottle warmer has cooled down completely and the plug has been removed from the wall outlet before cleaning. Use a damp soft cloth to clean the bottle warmer. Do NOT use bleach or any other harsh chemicals. The bottle warmer is NOT dishwasher safe. Dry thoroughly before  storing in a cool, dry place.

TROUBLE SHOOTING AND REPAIR

PROBLEM POSSIBLE CAUSE SOLUTION
The Warmer does not turn ON. There is no power. Check that there is power in

the electrical outlet.
The cord plug or the cord
connector has not been plugged in correctly, or they are damaged.| Check that the plug and connector have been plugged in correctly, and that they are in good condition. Should the product still not work, contact Customer Service.
Appliance was submerged in water.| Discard unit.
The feeding bottles are stained at the end of the sterilization cycle.| There are scale deposits in the appliance.| The Warmer needs to be descaled. See the “Descaling” section for more details.
High mineral content in tap water.| Use distilled water.
Noise – Incomplete cycle.| Excessive scale deposits on heating plate.| The Warmer needs to be descaled. See the “Descaling” section for more details.
Rapid scale build-up.| Use of tap water with high mineral content, softened or treated water.| Use distilled water.
The Warmer needs to be descaled. See the “Descaling” section for more details.

FOR MORE INFORMATION

Please do not return this product to the store.
If you have any questions or comments about this product, or are missing any of the parts, contact us in one of the following ways:

(877)-424-4226
info@chiccousa.com
www.chiccousa.com
1826 William Penn Way Lancaster, PA 17601

TECHNICAL INFORMATION

Reference: 00007390100070
Electrical Ratings: 220W 120V~ 60Hz
Model: 06867_MU
Made In China

= WARNING!
= WARNING! Hot Surface.
= WARNING! Hot Steam. Bottle Warmer E351537

www.chiccousa.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals