V-TAC VT-2629 Wi-Fi Enabled Smart IP65 Strip Light Installation Guide

V-TAC VT-2629 Wi-Fi Enabled Smart IP65 Strip Light

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC SMART LED Lighting. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 2 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This productiswarranted for manufacturing defects only.

Multi-Language Manual – QR CODE

Please scan the QR code to access the manual in multiple languages.

SAFETY WARNING

This marking indicates that this product should not be disposed of with other household wastes.

Caution, ,1,k of elect,lc shock.

IMPORTANT INSTRUCTIONS & FUNCTIONS

HOW TO CONNECT CONTROLLER WITH STRIPLIGHT

1. Remote control and Wifi controller function only can be used after setting with the application is complete
2. Please turn off the power before starting the installation.
3. When connecting the Wifi Controller to the striplight please ensure to connect the arrow marking side of the controller to the striplight displaying 12V. Please refer to the image below. For further installation steps please refer to the instruction manual section “INSTALLATION “.

WIFI CONTROLLER FUNCTIONS

1. IMPORTANT NOTE: Wifi controller functions can only be used after successfully pairing the strip light with V-TAC Smart Light APP.
2. The Wifi controller allows alternative method of enabling the controller into pairing mode for connecting with the APP. Press and hold the ON/OFF button for 7 seconds and wait for 3-5 seconds till you observe the light flashing. If the light flashes rapidly the controller is in Smart pairing mode OR if the light flashes slowly the controller is in AP pairing mode. To switch the pairing mode from the Smart mode to AP mode or vice versa please press and hold the ON/OFF button on the controller for 7 seconds.

Please refer to “APP INSTALLATION” instructions from the manual for further pairIng process.

REMOTE CONTROL FUNCTIONS

IMPORTANT NOTE:

1. Remote control functions can only be used after successfully pairing the strip light with  VTAC Smart Light APP.
2. Once the pairing has been successful! you can use the remote control even when your phone is powered off OR if the app has been deleted by mistake OR if the wifi has been disabled/ switched off/ restarting.
3. “CT+ ” and “CT-” : These buttons allow you to step by step switch from 3000K to 6400K. Tap on CT+ until you reach 6400K output and tap on CT- until you reach 3000K. This features allows you to set desired color temperature ranging from 3000K to 6400K. Thus allowing you to set 4000K temperature as well.
4. Memory function: It ensures the last used color/brightness/mode is used after you switch OFF and ON the light.

Remote Control Functions

| ON/OFF| | Red
| Increase Brightness| | Blue
| Decrease Brightness
Switch Q ~ Scene Modes| | Green
| Step by Step Step by Step 3000K(CT-) – 6400K(CT+)| | Cool White
| Return Key| | Warm White
| Multiple Color options

INSTALLATION

Step 1: Connect the adaptor, controller and strip light as per below diagram.

PARTS

APP INSTALLATION

Step 2: Scan the given QR code, or download “V-TAC Smart Light’ from the App Store (iOS) or the Google Play Store (Android).

For ANDROID

For Ios

Step 3: Open the V-TAC Smart Light app and tap on register for creating a new account.

Step 4:
A) Mobile Number: Select the country, then enter your mobile number. Once done, tap ‘Next’.
B) E-Mail: Enter your email id and tap on ‘Next’.

Step 5: Enter the verification code which will be sent to your mobile number/emai id, then assign a new password to your account and tap on “Confirm”.

Step 6: Tap on ‘Add Device’ or the+ sign. Make sure the lamp is switched on.

Step 7: Choose ‘Lighting’ to start pairing the light to the app .

Step 8: To pair the device with LED Smart Strip Light make sure the light is blinks rapidly. Once the light blinks rapidly, the light is in pairing mode. If the light is not blinking rapidly, you can do one of the following steps:
A. Switch the light on & off repeatedly for 3 times, with short intervals of less than 2 seconds.
B. Tap the ‘How to make light blink rapidly’ link (as shown on the image to the right)
C. You can also enable pairing mode from the Wi-Fi controller. Press and hold the ON/OFF button for 5-7 seconds and wait till you observe the light flashing. Please refer to the instruction section “WI-Fl CONTROLLER FUNCTIONS”

Network Modes:

1. Smart Mode: Light flashes rapidly.
2. AP mode: Slow flash, once every 2 seconds. Confirm if the light blinks rapidly, select the Wi-Fi network, and enter the password.

Step 9 Once you have successfully completed step 8, you will be redirected to below page, where the App searches, registers and initializes the device(lamp) (ref image below)

Step 10: Once your device is successfully added, rename the device to your preference.

Step 11: After successfully pairing the Wi-Fi receiver with the app, you can start controlling multiple features of the lamp through your mobile- on/off switch, timing & schedules, and more.

ALEXA SETTINGS

Step l: lnstall the Amazon Alexa app via the App Store(iOS) or the Play Store (Android) and register. If you already have an existing account with Amazon Alexa, please proceed to logging in.

Step2: Once you are on the Amazon Alexa home page, tap on the lower right icon – where the arrow is pointed-to add a new device and skill.

Step3: Tap on settings and tap on “skills and games” as shown below.

Step4: Search for ‘V-TAC Smart Light’ on the “Skills & Games” page as shown below.

Step 5: Enable the Skill.

Step6: Enter your V-TAC Smart Light login ID and password and tap on “Link Now”

Step 7: Once you tap on Link Now, you will be redirected to a new page requesting for authorization(Ref Image below). Tap on “Authorize”

Step8: You will receive confirmation of the account being linked successfully (Ref Image below)

Step8: Discover your smart device on Alexa. Once you have enabled the skill
A) You can use voice command” Alexa discover devices” to the Alexa device which you have.

B) To add device manually on home page tap on and tap on Add device, select the device which you are adding and tap on discover device.

Note: Discovering the device must be done every time the device’s name is changed on the app.

ALEXA Commands

Now, you can control your smart device using voice commands on Alexa. Below are a few commands you can use:

► ! Alexa, turn on/off bedroom light.
► ! Alexa, set bedroom light to 50 percent.

THINGS TO REMEMBER BEFORE STARTING INSTALLATION:

1. V-TAC Smart Light App & Amazon Alexa App
2. Make sure you have Amazon Alexa Device(including Echo, Echo Tap, or Echo Dot)
3. Smart Device – Lamp
4. Stable Wifi network

GOOGLE HOME SETTINGS

Stepl: a&b) Install the Google Home app via the App Store (iOS) or the Play Store (Android) and register. If you already have an existing account with Google Home, please proceed to logging in.
c) Create a New Home/Choose from the existing home if any. d) Power ON the Google Home device and connect it to the App.(Then Proceed to step 2)

Step2: Once you are on the Google home page, tap on the Add “+” icon-to add a new device and skill. And then tap on Set up device as shown in below image.

Step3: Make sure the Smart Bulb is paired with V-TAC Smart Light app before starting step 3. Tap on the arrow section as highlighted in the below image.

Step4: Type “V-TAC Smart Light” on the search bar and tap on the icon of “V-TAC Smart Light”

Step 5 : Sign In with your V-TAC Smart Light Login credentials to Link the Smart Light device

Step6: Tap on Authorize in order to proceed to linking the device

Step7 a. Account will now be linked, please stay on the page you will be redirected in few seconds to select the device to add to your home. b. Select the device and tap on Next as show in image b

Step8: Select the Home where you would like to add the Smart Light under. (Or) you can create a New home in order to add the Smart Light to it.

Step9: You have succesfully added Smart Light device to your Google home App.

Step 10:
a. You can turn the Lamp On/OFF by taping on On/Off options as shown below. (OR) You can tap on the Smart Lamp.

b. You will be redirected to page(as shown in image b) where you can control the lights “Power and Dimming functionality”

Google Commands:

Now, you can control your smart device using voice commands on Google Home. Below are a few commands you can use:

► ! OK Google, turn on/off bedroom light
► ! OK Google, set bedroom light to 50 percent.

THINGS TO REMEMBER BEFORE STARTING INSTALLATION:

1. V-TAC Smart Light App & Google Home App
2. Make sure you have Google Home Device
3. Smart Device – Lamp
4. Stable Wifz network

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>