SHURE ULXD4D-J50A Dual Channel Digital Wireless Microphone System User Guide
- June 9, 2024
- Shure
Table of Contents
SHURE ULXD4D-J50A Dual Channel Digital Wireless Microphone System User Guide
ULX-D Dual and Quad
Wireless Microphone System
User guide for Shure ULXD Dual and Quad wireless system. Includes setup
instructions, specifications, and troubleshooting. Version: 5.4 (2022-C)
Shure Incorporated
Table of Contents
ULX-D Dual and Quad Wireless Microphone System 4
Quickstart Instructions
4
General Description
4
Dual and Quad Receiver Models
5
Hardware Interface
6
Receiver
6
Receiver Home Screen
8
Transmitters
9
Boundary and Gooseneck Base Transmitters
10
Advanced Transmitter Features
11
Locking Controls and Settings
12
Home Screen Display Options
13
Menu Screens
14
Transmitter IR Presets
21
Creating a System Preset
21
Batteries
21
Battery Runtime Charts
22
Shure SB900 Series Rechargeable Battery
23
Important Tips for Care and Storage of Shure Recharge
able Batteries
23
Installing the Battery Contact Cover
23
Setting Receiver Gain
23
Receiver Gain Controls
24
Reading the Audio Meter
24
Muting a Receiver Channel Audio Output
24
Transmitter Input Clip
24
Audio Summing
25
Receiver Output Level
26
Scan and Sync
26
Multiple System Setup
27
Manual Frequency Selection
28
RF
28
Transmitter RF Power
28
Interference Detection
28
High Density Mode
29
Frequency Diversity
29
Setting Regional TV Format
30
Custom Groups
30
Audio Signal Encryption
31
RF Cascade Ports
31
Antenna Bias
32
Networking ULX-D Receivers
32
Network Control Software
32
IP Address Configuration
33
Networking Acronyms
33
Overview of Dante Network Modes
34
Network Connection and Configuration Examples
35
Assigning Network Device IDs for Shure Control and
Dante Control
40
Configuring Audio Routes with the Dante Controller 41
Network Troubleshooting
43
Restoring Dante Factory Settings
43
System Reset
44
Firmware
44
Firmware Versions
44
Updating the Receiver
44
Updating the Transmitter
45
Connecting to an External Control System
45
Setting the Gateway to Allow Cross Subnet Routing 45
2/64
Managing Your System with Shure Software
Troubleshooting Power Gain Cables Interface Locks Encryption Mismatch Firmware
Mismatch Tx Battery Hot Radio Frequency (RF)
Contact Customer Support
Accessories Furnished Accessories Optional Accessories
Specifications
Shure Incorporated
45
ULXD4D & ULXD4Q
52
ULXD1
54
46
ULXD2
55
46
Tables and Diagrams
56
46
Batteries
57
46
Frequency Range and Transmitter Output Power
57
46
46
IMPORTANT SAFETY INSTRUCTIONS
59
47
WARNING
60
47
47
Important Product Information
61
LICENSING INFORMATION
61
48
Information to the user
61
48
Australia Warning for Wireless
62
48
Certifications
62
50
Information to the user
63
51
3/64
ULX-D Dual and Quad Wireless Microphone System
Quickstart Instructions
Shure Incorporated
General Description
Shure ULX-DTM Digital Wireless offers uncompromising 24bit audio quality and
RF performance, with intelligent, encryptionen abled hardware, flexible
receiver options, and advanced rechargeability options for professional sound
reinforcement.
4/64
Shure Incorporated
A breakthrough in wireless audio quality, Shure digital processing enables
ULX-D to deliver the purest reproduction of source material ever available in
a wireless system, with a wide selection of trusted Shure microphones to
choose from. Extended 20 Hz 20 kHz frequency range and flat response
captures every detail with clarity, presence, and incredibly accurate low end
and transient response. With greater than 120 dB, ULXD delivers wide dynamic
range for excellent signaltonoise perfor mance. Optimized for any input
source, ULX-D eliminates the need for transmitter gain adjustments. ULX-D sets
a new and unprecedented standard for spectral efficiency and signal stability.
The intermodulation performance of ULXD is an incredible advancement in
wireless performance, enabling a dramatic increase in the number of
simultaneous ac tive transmitters on one TV channel. Rocksolid RF signal with
zero audio artifacts extends over the entire range. For applica tions where
secure wireless transmission is required, ULX-D offers Advanced Encryption
Standard (AES) 256-bit encrypted signal for unbreakable privacy. For
scalability and modular flexibility, ULX-D receivers come in single, dual, and
even quad channel versions. The dual and quad channel receivers offer
conveniences such as RF cascade, internal power supply, bodypack frequency
diversity, audio output channel summing, and DanteTM digital networking for
multi-channel audio over Ethernet. All receivers offer High-Density mode for
applications where high channel counts are needed, greatly increasing the
amount of simultaneous channels possi ble over one frequency band. Advanced
Lithium-ion rechargeability provides extended transmitter battery life over
alkaline batteries, battery life metering in hours and minutes accurate to
within 15 minutes, and detailed tracking of battery health status. Generations
ahead of any other available system in its class, ULX-D brings a new level of
performance to professional sound reinforcement.
Dual and Quad Receiver Models
The ULXD4 receiver is available in dual channel and quad channel models. Both
models share the same feature set and func tionality, but differ in the number
of channels available and the number of audio outputs. The descriptions and
procedures in this guide are applicable to either the dual or the quad
receiver.
ULXD4D Dual Receiver Supports 2 channels of wireless audio.
ULXD4Q Quad Receiver Supports 4 channels of wireless audio.
5/64
Hardware Interface
Receiver
Front Panel
Shure Incorporated
Infrared (IR) Sync Window
Sends IR signal to the transmitter for sync.
Network Icon
Illuminates when the receiver is connected with other Shure devices on the
network. IP address must be valid to enable networked control.
Encryption Icon
Illuminates when AES-256 encryption is activated.
LCD Panel
Displays settings and parameters.
Scan Button
Press to find the best channel or group.
Menu Navigation Buttons
Use to navigate and select parameter menus.
Control Wheel
Push to select a channel or menu item Turn to scroll through menu items or to
edit a parameter value
Channel Select Button
Press to select a channel.
Sync Button
Press the sync button while the receiver and transmitter IR windows are
aligned to transfer settings from the receiver to the transmitter.
RF Diversity LEDs
6/64
Shure Incorporated
Indicate antenna status:
Blue = normal RF signal between the receiver and transmitter Red =
interference detected Off = No RF connection between the receiver and
transmitter
Note: the receiver will not output audio unless one blue LED is illuminated.
RF Signal Strength LEDs
Indicate the RF signal strength from the transmitter:
Amber = Normal (-90 to -70 dBm) Red = Overload (greater than -25 dBm)
Audio LEDs
Indicate average and peak audio levels:
LED Red (6) Yellow (5) Yellow (4) Green (3) Green (2) Green (1)
Audio Signal Level -0.1 dBFS -6 dBFS -12 dBFS -20 dBFS -30 dBFS -40 dBFS
Description Overload/ limiter Normal peaks
Signal Present
Note: In Frequency Diversity mode, simultaneous blinking of the red and yellow audio LEDs indicates that diversity audio has been routed to this channel.
Gain Buttons
Press the gain buttons on the front of the receiver to incrementally adjust
gain from -18 to +42 dB.
Power Switch
Powers the unit on or off.
Back Panel
AC Power Input
IEC Connector, 100 – 240 V AC.
RF Antenna Diversity Input Jack (2)
7/64
Shure Incorporated
For antenna A and antenna B.
RF Cascade Jack (2)
Passes the RF signal from Antenna A and Antenna B to one additional receiver.
Mic/Line Switch (one per channel)
Applies a 30 dB pad in mic position.
Balanced XLR Audio Output (one per channel)
Connect to a mic or line level input.
Network Status LED (Green)
One per network port. Off = no link On = network link Flashing = network link
active
Ethernet/Dante Network Secondary Port
Connect to an Ethernet network to enable remote device control via Wireless
Workbench software. Also carries Dante digi tal audio and control signals for
audio distribution, monitoring, and recording – see Dante Network topic.
Network Speed LED (Amber)
One per network port. Off = 10/100 Mbps On = 1 Gbps
Ethernet/Dante Network Primary Port
Connect to an Ethernet network to enable remote device control via Wireless
Workbench. Also carries Dante digital audio and control signals for audio
distribution, monitoring, and recording – see Dante Network topic.
Receiver Home Screen
The home screen displays the following information for each receiver channel:
· Group and Channel · Transmitter Status: NoTx or TxOn, battery icon/remaining
battery life
Press the SEL button to access a channel menu screen.
8/64
Shure Incorporated
Transmitters
Power LED
Green = unit is powered on Red = low battery or battery error (see
Troubleshooting) Amber = power switch is disabled
On/Off Switch
Powers the unit on or off.
SMA Connector
Connection point for RF antenna.
LCD Display:
View menu screens and settings. Press any control button to activate the
backlight.
Infrared (IR) Port
Align with the receiver IR port during an IR sync for automated transmitter
programming.
Menu Navigation Buttons
Use to move through parameter menus and change values.
exit enter
Acts as a ‘back’ button to return to previous menus or parameters without confirming a value change Enters menu screens and confirms parameter changes Use to scroll through menu screens and to change parameter values
Battery Compartment
Requires Shure rechargeable battery or 2 AA batteries.
AA Battery Adapter
Handheld: rotate and store in the battery compartment to use a Shure
rechargeable battery Bodypack: remove to accommodate a Shure rechargeable
battery
Bodypack Antenna
For RF signal transmission.
Integrated Antenna
For RF signal transmission.
Microphone Cartridge
See Optional Accessories for a list of compatible cartridges.
TA4M / LEMO Input Jack
Connects to a microphone or instrument cable. 9/64
Shure Incorporated
Installing Bodypack Antennas
Hand-tighten antennas until secure. Do not use tools.
Boundary and Gooseneck Base Transmitters
10/64
Shure Incorporated
Power Button
Press to power on; press and hold to power off.
Mute/Active Button
Four settings are available for the mute/active button:
Toggle: Press to switch between active and mute states Push-to-Mute: Hold
button to mute microphone Push-to-Talk: Hold button to activate microphone
Disabled: Button functionality off
Mute LED
Indicates whether microphone is active or muted. The following settings are
available:
Active
Muted
Green*
Red*
Red
Off
Red
Flashing red
*MX400R series gooseneck microphones (red LED) do not offer this setting.
Low-Battery LED
Off = More than 30 minutes of battery life remain On (red) = Less than 30
minutes of battery life remain On (green) = Microphone docked on charging
station On (amber) = Battery is missing or is not inserted correctly
Infrared (IR) Port
Align with receiver IR port to send settings to transmitter.
Charge Connector
Connects to networked chargers and USB power supply.
Gooseneck Microphone
ULXD8 base fits 5″, 10″, and 15″ Microflex series microphones, available in
single or dualflex and with bi-color or red-only LEDs.
Advanced Transmitter Features
RF MUTE
Use this to turn on a transmitter without interfering with the RF spectrum.
Press and hold exit during power-on until RFMUTED is displayed. To un-mute,
restart the transmitter.
11/64
Shure Incorporated
MIC.OFFSET
MIC.OFFSET compensates for signal level differences between transmitters that
share the same receiver channel. Set the offset gain on a low signal level
transmitter to match a louder transmitter: UTILITY > MIC.OFFSET
Note: For normal gain adjustments, use the receiver gain buttons.
Transmitter Audio Mute Mode
Mute Mode reconfigures the transmitter power switch to act a mute switch for
the audio. Using the switch, the audio can be easily turned on or muted by
presenters, sports referees, or anyone who periodically needs to speak. When
the audio is muted, the transmitter RF signal remains on and ready at all
times.
Note: Mute Mode can be selected as an IRPRESET option.
To set a transmitter to Mute Mode: 1. From the transmitter menu: UTILITY >
MUTEMODE 2. Use the arrows to select ON or OFF. 3. Press enter to save.
Tip: The transmitter LED turns red when audio is muted and turns green when
audio is enabled. The display of the transmitter will show AUDIOMUTED and the
receiver display will show TxMuted.
Note: Mute Mode must be set to OFF in order to use the power switch to turn
off the transmitter.
Locking Controls and Settings
Use the LOCK feature to prevent accidental or unauthorized changes to the
hardware.
Receiver
Menu path: DEVICEUTILITIES > LOCK Use the control wheel to select and lock any
of the following receiver functions.
· MENU: All menu paths are inaccessible · GAIN: Front panel gain button is
disabled · POWER: Power switch is disabled · SCAN: Front panel SCAN button is
disabled and prevents frequency changes due to group scans initiated by other
ULXD
units · SYNC: Front panel SYNC button is disabled Tip: To unlock, press EXIT,
turn the control wheel to select UNLOCKED, and press ENTER to save.
Transmitter
Menu path: UTILITY > LOCK Use the transmitter controls to select and lock any
of the following transmitter functions.
· MENULOCK: All menu paths are inaccessible. · POWERLOCK: Power switch is
disabled
12/64
Shure Incorporated
Quick-Lock option: To turn on the transmitter with its power and menu
navigation buttons locked, press and hold the but ton during power-on until
the locked message is displayed. Tip: To unlock the MENULOCK, press the ENTER
button 4 times to pass through the following screens: UTILITY > LOCK >
MENUUNLOCK To unlock the POWERLOCK, set the power switch to the off position,
then press and hold the button while resetting the power switch to the on
position.
Home Screen Display Options
Receiver
The HOMEINFO menu provides options to change the information shown on the
receiver home screen: DEVICEUTILITIES > HOMEINFO Use the control wheel to
select one of the following screen displays.
Receiver home screen view 1
Receiver home screen view 2
Receiver home screen view 3
Transmitter
Home Screen: Press the arrows at the home menu to display one of the following
screens:
13/64
Shure Incorporated
Transmitter home screen view 1
Transmitter home screen view 2
Menu Screens
Receiver Channel
Transmitter home screen view 3
14/64
Shure Incorporated
Receiver Information
Use DEVICEUTILITIES > HOMEINFO to change the home screen display.
Gain Setting
-18 to +42 dB, or Mute.
Mic. Offset Indicator
Indicates offset gain is added to the transmitter.
Transmitter Settings
The following information cycles when a transmitter is tuned to the receiver’s
frequency: Transmitter Type Input Pad (Bodypack only) RF Power Level
Transmitter Lock Status Transmitter Mute Status
Battery Runtime Indicator
Shure rechargeable battery: runtime is displayed in minutes remaining. AA
batteries: runtime is displayed with a 5-bar indicator.
TV Channel
Displays the TV channel that contains the tuned frequency.
High Density Mode Icon
Displayed when High Density mode is enabled.
Transmitter Status
The following text or icons report transmitter status to the receiver screen:
Display Icon
Lo Nm Hi M P TxMuted -NoTx-
Transmitter Status Bodypack input is attenuated 12 dB Offset gain is added to the transmitter 1 mW RF power level 10 mW RF power level 20 mW RF power level Menu is locked Power is locked Displayed when the transmitter audio is set to off using the MUTEMODE feature No RF connection between a receiver and transmitter or transmitter OFF
15/64
Transmitter
Shure Incorporated
Transmitter Information
Scroll at the home screen to change the display
Power Lock Indicator
Indicates power switch is disabled
Transmitter Audio Muted Indicator
Displayed when the transmitter audio is set to off using the MUTEMODE feature.
Battery Runtime Indicator
Shure rechargeable battery: runtime is displayed in hours:minutes remaining AA
Batteries: runtime is displayed with a 5-bar indicator
Menu Lock Indicator
Indicates menu navigation buttons are disabled
Mic. Offset
Displays microphone offset gain value
RF Power
Displays RF power setting
Bodypack Input Pad
The input signal is attenuated 12 dB
Encryption Icon
Indicates encryption is enabled on the receiver and has been transferred to
the transmitter from a sync
Adjusting Receiver Display Brightness and Contrast
Adjust BRIGHTNESS and CONTRAST settings to improve visibility in challenging
lighting environments. 1. From the receiver menu: DEVICEUTILITIES > DISPLAY 2.
Press the control wheel to select CONTRAST or BRIGHTNESS.
16/64
Shure Incorporated
3. Turn the control to adjust the selected parameter. 4. Press ENTER to save
changes.
Editing Receiver Channel Name
To edit a receiver channel name, choose EDITNAME from the menu. · Turn the
control wheel to edit a highlighted character · Press the control wheel to
advance to the next character · Press ENTER to save changes
Note: The channel name is transferred to a transmitter during a sync.
Receiver Menu Descriptions
RADIO
Displays Group, Channel, Frequency, and TV information. Use the control wheel
to edit values
G:
Group for the selected frequency
CH:
Channel for the selected frequency
FREQUENCY
Selected frequency (MHz)
TV:
Displays the TV channel for the selected frequency
AUDIO
GAIN
Use the control wheel or gain buttons to adjust the channel gain from -18 to
42 dB, in 1 dB increments.
MUTE
Mutes the receiver audio output.
EDITNAME
Use the control wheel to assign and edit the selected receiver channel name.
IRPRESETS
BODYPACK/HANDHELD
BPPAD
17/64
Shure Incorporated
Sets the audio input attenuation options: KEEP, 0, -12.
LOCK
Sets the lock options: KEEP, Power, Menu, All, None
RFPOWER
Sets the transmitter RF power level: KEEP, 10mW=Nm, 1mW=Lo, 20mW=Hi.
BATT
Sets the transmitter battery type to ensure accurate metering: KEEP,
Alkaline,NiMH, Lithium
BPOFFSET
Adjustable gain to compensate for signal level difference between
transmitters: KEEP, 0 to 21 dB in 3 dB increments
HHOFFSET
Adjustable gain to compensate for signal level difference between
transmitters: KEEP, 0 to 21 dB in 3 dB increments
MUTE MODE
Configures the transmitter power switch to act as an audio mute switch.
Cust.Group
Create Custom Groups of up to 6 frequencies and export to networked receivers
GOOSENECK/BOUNDARY
HIGHPASS
Attenuates frequencies below 150 Hz by 12 dB per octave: KEEP, OFF, ON
RFPOWER
Sets the transmitter RF power level: KEEP, 10mW=Nm, 1mW=Lo, 20mW=Hi
BATTERY
Sets the transmitter battery type to ensure accurate metering: KEEP,
Alkaline,NiMH, Lithium
BNOFFSET
Adjustable gain to compensate for signal level difference between
transmitters: KEEP, 0 to 21 dB in 3 dB increments
GNOFFSET
Adjustable gain to compensate for signal level difference between
transmitters: KEEP, 0 to 21 dB in 3 dB increments
POWERLOCK
Locks the transmitter’s power button: KEEP, OFF, ON
Cust.Group
Create Custom Groups of up to 6 frequencies and export to networked receivers
18/64
Shure Incorporated
INITIALSTATEFROMCHARGER
Choose the transmitter’s state after it is removed from a charger: KEEP,
Active, Muted, OFF
MUTEBUTTONBEHAVIOR
Sets the mute button behavior: KEEP, Toggle, Push-to-Talk, Push-to-Mute,
Disabled
BNMUTELEDACTIVE/MUTE
Sets the mute LED colors for active and muted states: KEEP, Green/Red,
Red/OFF, Red/Flash-Red, OFF/OFF
GNMUTELEDACTIVE/MUTE
Sets the mute LED colors for active and muted states: KEEP, Green/Red,
Red/OFF, Red/Flash-Red, OFF/OFF
MUTELEDLIGHTBRIGHTNESS
Sets the mute LED brightness: KEEP, Normal, Low
BATTERYINFO
HEALTH
Percentage of charge capacity compared to a new battery
CHARGE
Percentage of charge capacity
CYCLES
Number of charge cycles logged by the battery
TEMP
Battery temperature: °C/°F
DEVICEUTILITIES
FREQDIVERSITY
OFF (default) 1+2 3+4 (quad only) 1+2/3+4(quad only)
AUDIOSUMMING
OFF (default) 1+2 3+4 (quad only) 1+2/3+4 (quad only) 1+2+3+4 (quad only)
ENCRYPTION
19/64
Shure Incorporated
Set encryption: ON/OFF Note: For some units, encryption cannot be turned off.
ADVANCEDRF
HIGH DENSITY: ON/OFF CUSTOM GROUPS: SETUP/EXPORT/CLEAR ANTENNA BIAS: ON/OFF
SWITCH BAND (Japan AB band only)
LOCK
MENU: LOCKED/UNLOCKED GAIN: LOCKED/UNLOCKED POWER: LOCKED/UNLOCKED SCAN:
LOCKED/UNLOCKED SYNC: LOCKED/UNLOCKED
HOMEINFO
Select screen options for Home Menu.
DISPLAY
CONTRAST BRIGHTNESS: LOW/MEDIUM/HIGH
NETWORK
CONFIGURATION: SWITCHED/REDUNDANT AUDIO/SPLIT SHURE CONTROL: DEVICE ID,
Network Mode, Set IP and Subnet values for Ethernet network DANTE: DANTE
DEVICE ID, AUDIO & CNTRL, REDUNDANT AUDIO, Set IP, Subnet, Gateway and Yamaha
values for
DanteTM network, DANTE DEVICE LOCK, DDM
Note: Additional information can be accessed from the selected networking
option.
TXFWUPDATE
IR DOWNLOAD, Tx Firmware Version
SYSTEMRESET
RESTORE: Default Settings, Presets SAVE: Create New Preset DELETE: Delete
Preset
VERSION
Model Band S/N (serial number) Ver Mcu FPGA
20/64
Boot
DANTE VERSIONS
REV FW HW BOOT USER CAP
Shure Incorporated
Transmitter IR Presets
Use the IRPRESETS receiver menu to quickly configure transmitter settings from the receiver screen. When a sync is per formed between the receiver and transmitter, the IR PRESETs automatically configure the transmitter. Each parameter has the default value KEEP, which leaves that setting unaffected by a sync.
Feature
Setting
BPPAD
+0 dB, -12 dB
LOCK
Power, Menu, All, None
RFPOWER
10mW=Nm (normal), 1mW=Lo (low), 20mW=Hi (high)
BATT
Alkaline, NiMH, Lithium
BPOFFSET
0 dB to +21 dB (in 3 dB increments)
HHOFFSET
0 dB to +21 dB (in 3 dB increments)
MUTEMODE
OFF, ON
Cust.Group
OFF, ON
Note: When Cust.Groups is set to on, it may take up to 30 seconds to complete an IR sync.
Creating a System Preset
System Presets allow a current receiver setup to be saved and restored.
Presets store all receiver settings to provide a quick way to configure a
receiver or switch between several different setups. Up to 4 presets can be
stored in receiver memory. To save the current receiver setup as a new preset:
DEVICEUTILITIES > SYSTEMRESET > SAVE > CREATENEWPRESET Use the control wheel
to name the preset, and then press Enter to save. To recall a saved preset:
DEVICEUTILITIES > SYSTEMRESET > RESTORE Use the control wheel to select the
preset name, and then press Enter.
21/64
Batteries
Shure Incorporated
The transmitter runs on two AA batteries or a Shure SB900 series rechargeable
battery. Use the included AA battery adapter when using batteries other than
the Shure rechargeable battery. Bodypack: Remove the adapter when using the
Shure rechargeable battery Handheld: Rotate and store the adapter in battery
door when using Shure rechargeable battery
Battery Runtime Charts
A 5-segment icon on the receiver and transmitter menu screens indicates
battery charge. For accurate battery runtime monitoring, set the transmitter
to the appropriate battery type: UTILITY > BATTERY > SET.AA.TYPE. The tables
display the approximate hours and minutes remaining (h:mm).
Alkaline
Battery Indicator
UHF/VHF
1/10 mW 20 mW
9:00 to 6:30
5:45 to 4:15
6:30 to 4:00
4:15 to 3:00
4:00 to 1:45
3:00 to 1:30
1:45 to 0:45
1:30 to 0:30
ISM/1.x
1/10mW
7:30 to 5:30
5:30 to 3:30
3:30 to 1:45
1:45 to 0:45
20mW
5:30 to 4:00
4:00 to 2:45
2:45 to 1:30
1:30 to 0:30
<0:45
<0:30
<0:45
<0:30
Replace
Replace
Replace
Replace
22/64
Shure Incorporated
Shure SB900 Series Rechargeable Battery
When using a Shure rechargeable battery, the receiver and transmitter home
screens display the number of hours and minutes remaining. Detailed
information for the rechargeable battery is displayed in the receiver
BATTERYINFO menu and the transmitter menu: UTILITY > BATTERY > BATT.STATS
HEALTH: Displays battery health as a percentage of the charge capacity of a
new battery. CHARGE: Percentage of a full charge CYCLES: Number of times the
battery has been charged TEMP: Battery temperature in Celsius and Fahrenheit
Note: For additional rechargeable battery information, visit www.shure.com.
Important Tips for Care and Storage of Shure Rechargeable Batteries
Proper care and storage of Shure batteries results in reliable performance and
ensures a long lifetime. · Always store batteries and transmitters at room
temperature · Ideally, batteries should be charged to approximately 40% of
capacity for long-term storage · During storage, check batteries every 6
months and recharge to 40% of capacity as needed
Installing the Battery Contact Cover
Install the included battery contact cover (65A15947) on the handheld
transmitter to prevent light reflection in broadcast and performance
situations.
1. Align the cover as shown. 2. Slide the cover over the battery contacts
until it is flush with the transmitter body.
Note: Slide the cover off before inserting the transmitter in the battery
charger.
Setting Receiver Gain
The receiver gain control sets the audio signal level for the entire receiver
and transmitter system. Changes to the gain settings occur in realtime
allowing for adjustments during live performances. When adjusting the gain,
monitor the audio meter levels to prevent signal overloads.
23/64
Shure Incorporated
Receiver Gain Controls
The gain can be adjusted by using the gain buttons or by entering the AUDIO
menu and using the control wheel. Tip: To quickly adjust the gain, press and
hold a gain button to enable accelerated scrolling.
Reading the Audio Meter
The audio meter displays yellow, green, and red LEDs to indicate the audio
signal level. Audio peaks illuminate the LEDs for 2 seconds, while the RMS
signal is displayed in realtime. When setting up the receiver, adjust the gain
so that the average signal LED levels are solid green and occasionally yellow,
with only the highest peaks causing the red LED to illuminate.
Tip: If a vocalist is overloading a bodypack transmitter, try lowing the
receiver gain. If additional attenuation is needed, use the transmitter menu
to set the IN PUTPAD to -12dB. Note: Illumination of the red OL (overload) LED
indicates the internal limiter is engaged to prevent digital clipping.
Muting a Receiver Channel Audio Output
The audio output of each receiver channel can be independently muted to
prevent audio from passing. Mute status is indicated by RxMUTED message
appearing on the receiver display in place of the gain value.
Note: Receiver gain is disabled for muted channels to prevent unexpected
changes in audio levels.
To set a receiver channel output to mute: 1. AUDIO > MUTE 2. Use the control
wheel to select ON or OFF. 3. Press ENTER to save.
To unmute the receiver output: Simultaneously press the buttons or select OFF
from the MUTE menu option.
Tip: Audio mute can be enabled remotely from Wireless Workbench or from an
external controller.
Important! A power cycle will reset the receiver and unmute the audio output.
Transmitter Input Clip
The following warning displays on the receiver LCD panel when the transmitter
input is clipped:
24/64
Shure Incorporated
To correct, select INPUTPAD from the main menu and attenuate the input signal
by 12 dB. If the warning persists, reduce the level of input signal.
Audio Summing
Audio summing allows the dual and quad receivers to function as a 2 or 4
channel mixer, respectively. Summed audio is avail able on all outputs (Dante
and XLR). For example, when 1+2 is selected (see diagram), the outputs of
channels 1 and 2 sup ply the summed audio of the two channels.
Choosing an Audio Summing Mode
The following Audio Summing mode options are available:
To select an Audio Summing mode:
1. Menu: DEVICEUTILITIES > AUDIOSUMMING 2. Use the control wheel to select an
option, and then press Enter.
Note: When set to OFF, Audio Summing is disabled.
25/64
Shure Incorporated
Adjusting Gain for Summed Outputs
Use the gain controls for each channel to create the overall mix balance. The
front panel LEDs indicate the audio level for each channel. If an overload
occurs, the red LEDs will illuminate indicating that the internal limiter is
active and the display will show an overload message. To correct, adjust the
overall gain balance.
Receiver Output Level
The following table describes the typical total system gain from the audio
input to the receiver outputs:
Receiver Output Gain
Output Jack XLR (line setting) XLR (mic setting)
System Gain (gain control = 0dB) +24 dB -6 dB*
*This setting matches a typical wired SM58 audio signal level.
Scan and Sync
Use this procedure to tune a receiver and transmitter to the best open
channel.
Important! Before you begin:
Turn off all transmitters to prevent them from interfering with the frequency
scan.
Turn on any devices that might produce interference during the show so the
scan can detect and avoid them, including:
· Other wireless systems or devices · Computers · CD players · Large LED
panels · Effects processors
1. Press SEL to select a receiver channel. 2. Perform a group scan on the
receiver: SCAN > GROUPSCAN. 3. Press SCAN. While the scan is running, SCANNING
appears on the screen. 4. When the scan is done, the receiver displays the
group with the most available frequencies. Press the flashing ENTER
button to deploy frequencies to each receiver channel. 5. Power on the ULXD
transmitter. 6. Press the sync button on the receiver. 7. Align the IR windows
until the receiver IR port turns red.
Note: When complete, SYNCSUCCESS! appears. The transmitter and receiver are
now tuned to the same frequency.
26/64
Shure Incorporated
Multiple System Setup
A setup using networked receivers is the fastest and easiest way to distribute
the best open channel to each system. See Net working ULX-D Receivers for
networking details.
Note: Networked receivers must all be within the same frequency band.
Networked Receivers
1. Turn on all receivers. 2. Conduct a group scan on the first receiver to
find available frequencies in each group: SCAN > GROUPSCAN. 3. Press ENTER to
accept the group number and automatically assign the next best channel to each
receiver on the net
work. The receiver LEDs will flash when a frequency has been assigned. 4. Turn
on a transmitter and sync to the receiver.
Important! Leave the transmitter on and repeat this step for each additional
system.
Non-networked Receivers
1. Turn on all receivers. 2. Conduct a group scan on the first receiver to
find available frequencies in each group: SCAN > SCAN > GROUPSCAN >
SCAN 27/64
Shure Incorporated
3. When the scan is complete, use the control wheel to scroll through each
group. Press ENTER to select a group that has enough available frequencies for
all channels in the system.
4. Sync a transmitter to each receiver channel.
Important! Leave all transmitters on use the following steps to set up
additional receiver channels:
1. Set each additional receiver channel to the same group as the first
receiver: RADIO > G: 2. Conduct a channel scan to find available frequencies
within the group: SCAN > SCAN > CHANNELSCAN > SCAN 3. When the scan is
complete, press ENTER to assign frequencies to each receiver channel. 4. Sync
a transmitter to each receiver channel.
Manual Frequency Selection
To manually adjust group, channel, or frequency:
1. Press SEL to choose a receiver channel and navigate to the RADIO menu. 2.
Use the control wheel to adjust the group, channel, or frequency. 3. Press
ENTER to save changes.
RF
Transmitter RF Power
Reference the following table for setting RF Power:
RF Power Setting
System Range
1 mW
33 m (100 ft.)
10 mW
100 m (330 ft.)
20 mW
100 m (330 ft.)
Application For increased channel reuse at close distances
Typical setups For hostile RF environments or longdistance ap plications
Note: Using the 20 mW setting decreases the transmitter battery runtime and
reduces the number of compatible systems.
Interference Detection
Interference Detection monitors the RF environment for potential sources of
interference which can cause audio dropouts. When interference is identified,
the RF LEDs illuminate red and the following warning displays on the receiver
LCD panel. If the warning display persists or the audio drops out repeatedly,
perform a Scan and Sync at the first opportunity to find a clear frequency.
28/64
Shure Incorporated
High Density Mode
High Density mode creates additional bandwidth for more channels in crowded RF
environments. Frequency efficiency is opti mized by running at 1 mW RF
transmit power and narrowing the modulation bandwidth, allowing for the
channel spacing to be reduced from 350 kHz to 125 kHz. Transmitters can be
positioned on adjacent channels with unsubstantial intermodulation dis tortion
(IMD). High Density mode is ideal for applications where many channels are
needed in a confined area, transmission distances are short, and the number of
available frequencies is limited. Up to 30 meters of range is available in
High Density mode.
Setting the Receiver to High Density Mode
To set the receiver to High Density mode: DEVICEUTILITIES > ADVANCEDRF >
HIGHDENSITY Use the control wheel to set HIGHDENSITY to ON. When prompted,
sync the transmitter and receiver to enable HIGHDENSITY mode.
Note: When the receiver is in HIGHDENSITY mode, the following indicators are
shown on the receiver display:
· The HD icon will appear on the receiver display · The receiver band name
will be shown with an “HD” added. (example: The G50 band will appear as G50HD)
· The transmitter group and channel are assigned letters instead of numbers
(example: G:AA CH:AA)
Best Practices for High Density Mode
· When band planning, position ULX-D High Density channels in a range of
frequencies separated from other devices. · Use a separate RF zone for ULX-D
High Density channels to prevent intermodulation distortion from other
devices. · During High Density channel scanning, turn on all other
transmitters and move them to their intended position. · Perform a walk test
to verify transmitter range · If using custom groups, the groups loaded into
the receiver must be compatible with High Density mode
Frequency Diversity
Frequency diversity is an advanced ULXD receiver feature that safeguards
against loss of audio signal caused by RF interfer ence or by power loss in a
transmitter. In frequency diversity mode, the signals from two transmitters
from a common audio source are routed to the outputs of 2 re ceiver channels.
In the event of interference or power loss, the audio from the good channel is
switched to both outputs to pre serve the audio signal. Switching between
channels is seamless and inaudible. When the receiver senses that the signal
quality has improved, audio routing is restored without interrupting the audio
signal.
Note: In Wireless Workbench, you can selectively lock the diversity audio
source to a specific transmitter. See “Lock or Unlock a Frequency Diversity
Channel” in the Wireless Workbench help system for more on this.
Best Practices for Frequency Diversity
· Use the same microphone type and model for each transmitter · Place
microphones within close proximity to the source · Use the gain controls to
match the output levels for each receiver channel · If audio summing is
active, use a Y-cable (Shure AXT652) to connect the bodypacks to a single
audio source to prevent
comb filtering
29/64
Shure Incorporated
Choosing Diversity Output Routing
The following receiver channel routing output options are available:
· 1+2 · 3+4 (quad only) · 1+2/3+4 (quad only)
To enable frequency diversity and select a routing option: DEVICEUTILITIES >
FREQDIVERSITY Use the control wheel to choose a routing option, and then press
ENTER.
Note: Choose OFF to disable frequency diversity.
Frequency Diversity and Encryption
Enabling encryption while in frequency diversity mode provides an additional
layer of protection by only passing audio from the most recently synced
encrypted transmitter for each receiver channel.
Setting Regional TV Format
To ensure accurate display of TV channel information, set the TVFORMAT to
match the TV channel bandwidth in the region where the receiver is operating.
TV bandwidth varies globally, so check local regulations to determine the
regional TV band width. The following TVFORMAT options are available:
· 6MHz · 7MHz · 8MHz · 6MHzJAPAN · NOTV (use to turn off TV channel display or
in regions where TV channels are not applicable) To set the TVFORMAT:
1. Menu: DEVICEUTILITIES > ADVANCEDRF > TVFORMAT 2. Use the control wheel to
select a TVFORMAT option. 3. Press ENTER to save.
Custom Groups
Use this feature to create and export up to 6 groups of manually selected
frequencies to networked receivers prior to a group scan to simplify system
set up.
Tip: Use Wireless Workbench or Wireless Frequency Finder to select the best
compatible frequencies. See www.shure.com for more information.
To create a custom group: DEVICEUTILITIES > ADVANCEDRF > CUSTOMGROUPS > SETUP
Use the control wheel to choose group, channel and frequency values. Press
ENTER to save. Prior to performing a group scan, export a custom group to
networked receivers:
1. Go to DEVICEUTILITIES > ADVANCEDRF > CUSTOMGROUPS > EXPORT 2. Press the
flashing ENTER button to export all custom groups to all receivers on the
network.
Note: Use the CLEARALL option to remove all custom group settings.
30/64
Shure Incorporated
Audio Signal Encryption
When encryption is enabled, the receiver generates a unique encryption key
which is shared with a the transmitter during an IR sync. Transmitters and
receivers that share an encryption key form a protected audio path, preventing
unauthorized access from other receivers.
Note: For some units, encryption is always on and cannot be configured.
Encrypting a Single Transmitter to a Single Receiver
1. From the receiver menu: DEVICEUTILITIES > ENCRYPTION > ON(Auto) 2. Press
ENTER. 3. Perform an IR Sync to share the encryption key with the selected
transmitter.
Encrypting Multiple Transmitters to a Single Receiver
Multiple transmitters can share the same encryption key, allowing them access
to a single receiver. Use this method if you have multiple instruments or wish
to use a combination of handheld and bodypack transmitters.
1. From the receiver menu: DEVICEUTILITIES > ENCRYPTION > ON(Manual) >
KEEPKEYS. 2. Press ENTER. 3. Perform an IR Sync to share the encryption key
with the first transmitter. 4. Turn off the transmitter and perform an IR Sync
to share the key additional transmitters.
Caution! Make sure only one transmitter is turned on during an IR sync or a
performance to avoid causing cross interference between transmitters.
Regenerating Encryption Keys
Periodically regenerating the encryption key maintains security for
transmitters and receivers that are paired for extended peri ods.
1. From the receiver menu: DEVICEUTILITIES > ENCRYPTION > ON(Manual) >
REGENERATEKEYS. 2. Press ENTER. 3. Perform an IR Sync to share the encryption
key with the first transmitter. 4. Turn off the transmitter and perform an IR
Sync to share the key additional transmitters.
Caution! Make sure only one transmitter is turned on during an IR sync or a
performance to avoid causing cross interference between transmitters.
Removing Encryption
Note: For some units, encryption is always on and cannot be configured.
1. From the receiver menu: DEVICEUTILITIES ENCRYPTION OFF 2. Press ENTER. 3.
IR Sync the transmitter and receiver to clear the encryption key.
Note: If multiple transmitters are encrypted to a single receiver, each
transmitter must be IR synced to clear the encryption key.
RF Cascade Ports
The receiver has 2 RF cascade ports on the rear panel to share the signal from
the antennas with 1 additional receiver. Use a shielded coaxial cable to
connect the RF cascade ports from the first receiver to the antenna inputs of
the second receiv er.
Important! The frequency band must be the same for both receivers.
31/64
Shure Incorporated
Antenna Bias
Antenna ports A and B provide a DC bias to power active antennas. Set the DC
power to off when using passive (nonpow ered) antennas. To turn bias off:
DEVICEUTILITIES > ADVANCEDRF > ANTENNABIAS > OFF
Networking ULX-D Receivers
ULX-D Dual and Quad receivers feature a Dante dual-port network interface.
Dante technology provides an integrated solution to distribute digital audio,
manage control signals, and carry Shure Control (WWB and AMX/Crestron)
signals. Dante uses standard IP over Ethernet and safely coexists on the same
network as IT and control data. Selectable Dante networking modes route port
signals for flexible network set up.
Network Control Software
You can remotely manage and monitor your ULXD receivers using Wireless
Workbench and monitor digital audio routing us ing the Dante Controller.
Signals for AMX and Crestron controllers are carried on the same network as
Shure Control.
Shure Control
Wireless Workbench (WWB) software provides comprehensive control for wireless
audio systems. Wireless Workbench en ables live remote adjustments to
networked receivers for real-time changes to gain, frequency, RF power, and
control locks. A familiar channel strip interface displays audio meters,
transmitter parameters, frequency settings and network status. Wireless
Workbench is available for Windows or Mac and can be downloaded at:
www.shure.com/wwb
Dante
The Dante controller is a free software program created by AudinateTM to
configure and manage a network of Dante enabled devices. Use the controller to
create audio routes between networked components and to monitor the status of
online devices. Visit www.audinate.com for download and installation
instructions.
Dante Controller and Lock Settings
Version 2.4.X introduces support for Dante Device Lock for ULXD4D and ULXD4Q.
Dante Device Lock is a feature of Dante Controller that allows you to lock and
unlock supported Dante devices using a 4-digit PIN (Personal Identification
Number). When a device has a Dante lock turned on, Dante audio will continue
to flow according to existing subscriptions, but its sub scriptions and
settings can’t be controlled or configured. If you forget your Dante Device
Lock PIN, see the Device Lock section of the Dante Controller User Guide for
instructions on how to proceed.
Dante Domain Manager
Version 2.4.X introduces support for Dante Domain Manager (DDM) for ULXD4D and
ULXD4Q. DDM is network management software that enables user authentication,
role based security, and audit capabilities for Dante networks and Dante-
enabled products. Considerations for Shure devices controlled by DDM:
· When you add Shure devices to a Dante domain, leave the local controller
access setting in Read Write. Otherwise, ac cess to Dante settings, device
factory reset, and device firmware updates will be disabled.
32/64
Shure Incorporated
· When a device is managed by a Dante Domain and the Dante Domain is
disconnected, access to Dante settings, device factory reset and device
firmware updates will be disabled. When a device reconnects to the Dante
Domain, it follows the policy set for it in the Dante Domain.
See the Dante Domain Manager User Guide for more information.
IP Address Configuration
An IP address must be assigned to each device in the network to ensure
communication and control between components. Valid IP addresses can assigned
automatically using a DHCP server or manually from a list of valid IP
addresses. If using Dante audio, a separate Dante IP address must also be
assigned to the receiver.
Automatic IP Addressing
1. If using a DHCP capable Ethernet switch, set the DHCP switch to ON. 2. Set
the IP Mode to Automatic for all receivers: DEVICEUTILITIES > NETWORK >
SHURECONTROL > NETWORK 3. Use the control wheel to set the mode to Automatic,
press ENTER to save.
Note: Use only one DHCP server per network.
Manual IP Addressing
1. Connect the receivers to an Ethernet switch. 2. Set the IP Mode to Manual
for all devices: DEVICEUTILITIES > NETWORK > SHURECONTROL > NETWORK 3. Use the
control wheel to set the mode to Manual. 4. Set valid IP addresses and subnet
values for all devices, press ENTER to save.
Dante IP Addressing
IP addresses for a Dante network can assigned automatically using a DHCP
server or manually from a list of valid IP address es
To select the Dante IP addressing mode (Automatic or Manual): DEVICEUTILITIES
NETWORK > DANTE > AUDIO&CNTRL
Use the control wheel to select the mode, and then press ENTER to save.
Networking Acronyms
DHCP: Dynamic Host Configuration Protocol LAN: Local Area Network MCU: Micro
Controller Unit RJ45: Ethernet connection RX: Receiver
33/64
Shure Incorporated
TX: Transmitter WWB: Wireless Workbench software VLAN: Virtual Local Area
Network MAC: Machine Access Code
Overview of Dante Network Modes
The Dante network interface has two ports (Primary and Secondary) to provide
flexible routing and configuration options for network signals. Three
selectable Dante network modes are available to control signal routing from
the receiver ports to the Dante network.
Network Mode
Port Function and Signals
Secondary
Primary
Application
SWITCHED
Shure Control
Dante Audio and Control
Shure Control
Dante Audio and Control
For single network Installations of star or daisy-chained networks.
REDUNDANT Dante Redun
AUDIO
dant Audio
Shure Control
Dante Audio and Control
Primary and Secondary ports are configured are 2 separate networks. The Secondary port carries a backup copy of the Primary digital audio signal.
SPLIT
Dante Audio and Control
Primary and Secondary ports are configured are 2 separate networks Shure
Control
to provide isolation between control signals and audio signals.
Setting the Dante Networking Mode
Select a Dante mode to configure network signal routing on the Primary and
Secondary ports. Set all receivers on the network to the same mode.
Note: Remove network connections from the receiver before changing the mode.
1. From the receiver menu: DEVICEUTILITIES > NETWORK > CONFIGURATION 2. Use
the control wheel to select a mode (SWITCHED, REDUNDANTAUDIO, SPLIT) 3. Press
ENTER to save. 4. Cycle receiver power to enable the mode change.
34/64
Shure Incorporated
Network Connection and Configuration Examples
Note: Use shielded Cat5e cable for network connections to ensure reliable
performance.
Switched Mode
Switched mode is typically used for single network installations of star or
daisychained networks. Switched mode is recom mended for installations that
don’t require Dante audio. Network characteristics:
· Dante Audio and Shure Control are present on both the Primary and Secondary
ports · The Dante IP address and the Shure Control IP address must be on the
same subnet. The computer running Wireless
Workbench must also be on this subnet.
Network Example (Dante Audio + Wireless Workbench)
Computer
35/64
Connect the computer running the Dante controller and Wireless Workbench to
the Primary port.
DHCP Server
Can be configured with or without a DHCP server. Do not route audio through
the server.
Gigabit Ethernet Switch
Do not connect both network ports to the same Ethernet switch Use a star
network topology to minimize audio latency
Receiver Connection
Connect receivers to the Primary port
Dante Receiver
Connect Dante receivers (mixers, recorders, amplifiers) to the Primary port.
Shure Incorporated
Network Example (Wireless Workbench Only)
Computer
Connect the computer running Wireless Workbench to the Primary port.
DHCP Server
Can be configured with or without a DHCP server.
Receiver Connection
Connect receivers to the Primary port
36/64
Shure Incorporated
Redundant Audio Mode
Use redundant mode to carry a backup copy of the Dante audio on the Secondary
network in case the audio on the primary network is interrupted.
Network characteristics:
· Dante Primary Audio and Shure Control are present on the Primary port ·
Backup Dante audio is present on the Secondary port · The Primary Dante IP
address and the Shure Control IP address must be on the same subnet. The
computer running
Wireless Workbench must also be on this subnet. · The Secondary Dante IP
Address must be set to a different subnet
Note: Devices connected to the Redundant network must be compatible with
Redundant audio.
Network Example
Computer
Connect the computer running the Dante controller and Wireless Workbench to
the Primary port.
DHCP Server
Can be configured with or without a DHCP server. Do not route audio through
the server.
Gigabit Ethernet Switches
Use dedicated switches for the Primary and Secondary networks
37/64
Shure Incorporated
Do not connect both network ports to the same Ethernet switch Use a star
network topology to minimize audio latency
Receiver Connection
Connect Primary and Secondary ports to dedicated switches.
Note: The Secondary port only supports manual IP or automatic Link-Local
configuration. The Link-Local Dante Secondary address subnet is preset to
172.31.x.x (255.255.0.0)
Dante Receiver
Connect Dante receivers (mixers, recorders, amplifiers) to the Primary or
Secondary ports.
Split Mode
Use Split Mode to isolate control signals from audio signals by placing them
on two separate networks.
Network Characteristics:
· Shure Control is present on the Primary port · Dante Audio is present on the
Secondary port · The IP addresses for Dante and Shure Control must be on
different subnets
38/64
Network Example
Computer (Dante Controller)
Connect the computer running the Dante controller to the Secondary port.
DHCP Server (Secondary Network)
Can be configured with or without a DHCP server. Do not route audio through
the server.
Gigabit Ethernet Switch (Secondary Network)
Use dedicated switches for the Primary and Secondary networks Do not connect
both network ports to the same Ethernet switch Use a star network topology to
minimize audio latency
Receiver Connections (Dante Audio)
Connect the Secondary ports to the Secondary network switch.
Computer (Shure Control)
Connect the computer running the Shure Control to the Primary port.
DHCP Server (Primary Network)
Can be configured with or without a DHCP server. Do not route audio through
the server.
Gigabit Ethernet Switch (Primary Network)
Use dedicated switches for the Primary and Secondary networks Do not connect
both network ports to the same Ethernet switch Use a star network topology to
minimize audio latency
Receiver Connections (Shure Control)
Connect the Primary ports to the Primary network switch.
Dante Receiver
Connect Dante receivers (mixers, recorders, amplifiers) to the Primary port.
Shure Incorporated
39/64
Shure Incorporated
Assigning Network Device IDs for Shure Control and Dante Control
When using the receiver in a network with Shure Control (Wireless Workbench)
and a Dante Controller, two Device IDs are re quired: one for Shure Control
and one for Dante Control. Device IDs are used to identify devices on the
network and for creat ing Dante digital audio routes.
Best Practices
Using the following best practices will help to organize network setup and
ease troubleshooting. · For consistency, convenience, and easy
troubleshooting, use the same device ID for both Wireless Workbench (Shure
Control) and for the Dante network. · The Dante network requires unique Dante
device IDs to prevent a loss of audio signal routing. Any duplicate IDs on the
network will be tagged with a number such as -1, -2, -3, etc…. and must be
changed to a unique value. · Wireless Workbench (Shure Control) does not
require unique device IDs and duplicates do not affect the Dante network;
however, a best practice is to use unique device IDs.
Setting the Shure Control Device ID
1. Launch Wireless Workbench. 2. In the inventory, double-click the device ID
to edit it. Tip: Click the device icon next to the channel name flash the
front panel and identify the receiver.
40/64
Shure Incorporated
You can also update the Shure control device ID from the receiver front panel:
1. From the receiver menu: DEVICEUTILITIES > NETWORK > SHURECONTROL > Dev.ID
2. Use the control wheel to edit the ID. 3. Press ENTER to save.
Creating a Dante Device ID
There are two ways to create a Dante ID:
1. Enter the ID using the receiver menu. 2. Enter the ID using a keyboard
from the Dante controller.
If entering IDs from the receiver menu, additional ID modes are available for
quickly adding sequential numbering to multiple receivers or adding a prefixes
for network discovery by Dante enabled Yamaha mixing consoles.
Note: Changing the Dante ID will cause a loss of audio signal. After an ID has
been changed, use the Dante controller to restore audio route subscriptions us
ing the new ID.
Setting the Device ID from the receiver menu:
1. DEVICEUTILITIES > NETWORK > DANTE > Dev.ID 2. Use the control wheel to
select an IDMODE:
Off: Manually enter an ID by using the control wheel. Press ENTER to save.
Sequential: Adds a 3-digit numerical prefix to the receiver model name to
create the device ID. (ex: 001-Shure-
ULXD). Use the control wheel to increment the prefix value. Press ENTER to
save. Yamaha: Adds a prefix starting with “Y” followed by 3-digits to the
receiver model name to create a device ID that
allows Dante enabled Yamaha mixing consoles to discover ULX-D receivers on a
Dante network. (ex: Y001-ShureULXD). Use the control wheel to increment the
prefix numerical value. Press ENTER to save.
Entering the Device ID from the Dante controller:
1. Open the DeviceView and select the receiver from the pulldown menu. 2.
Click on the DeviceConfig tab. 3. Enter the ID in the RenameDevice box and
press ENTER.
Viewing Dante Device IDs in the Dante Controller
Dante device IDs are displayed in the NetworkView window in the Dante
Controller. 1. Launch the Dante controller and open the NetworkView window. 2.
Verify that the Dante device IDs match the IDs entered in the receiver.
Identify Device Feature
The Dante controller’s Identify Device feature flashes the front panel LEDs of
a selected receiver to provide identification when multiple receivers are in
use. Open the DeviceView in the Dante controller and click on the identify
icon (eye). The front panel LEDs of the selected receiver will respond by
flashing.
Configuring Audio Routes with the Dante Controller
Devices that appear in the Dante controller are categorized as “Transmitters”
and “Receivers” In order for audio to flow in the network, audio routes
(subscriptions) must be configured between transmitters and receivers.
Note: ULX-D receivers will appear in the Dante controller as a Transmitter.
Devices that have both inputs and outputs commonly appear as both transmitters
and receivers.
41/64
Shure Incorporated
Dante Transmitters
Devices that send or add audio into the network such as:
· Receiver Outputs · Amplifier Outputs · Mixer Outputs · Signal Processor
Outputs · Recorder Playback Outputs
Dante Receivers
Devices that receive audio from the network such as:
· Amplifier Inputs · Mixer Inputs · Signal Processor Inputs · Recorder Inputs
Forming an Audio Route
Launch the Dante Controller and click on the intersection point between
components to form an audio route. The audio route is also referred to as a
Subscription.
1. Find the intersection between the transmitter and receiver channels.
2. Click on the
where the components meet.
3. A green checkmark
indicates that the audio route has been established.
4. Check the audio to verify that the audio route has been formed.
For additional information about the Dante controller, visit www.audinate.com.
42/64
Shure Incorporated
Network Troubleshooting
· Use only one DHCP server per network · All devices must share the same
subnet mask · All receivers must have the same level of firmware revision
installed · Look for the illuminated network icon on the front panel of each
device:
If the icon is not illuminated, check the cable connection and the LEDs on the
network jack. If the LEDs are not on and the cable is plugged in, replace the
cable and recheck the LEDs and network icon. For more information, see
Wireless Workbench network troubleshooting.
Restoring Dante Factory Settings
The receiver and the Dante network card can be reset to restore factory Dante
settings. Performing a reset is helpful for clear ing existing data before
setting up a system. Caution! Performing a reset on either the Dante network
card or on the ULX-D receiver will interrupt the Dante audio. Tip: Prior to
performing a factory reset, note the current Dante network mode and IP
settings. After a reset, the Dante network mode reverts to SWITCHED, and the
IP address mode revert to AUTO.
Restoring Receiver and Dante Card Factory Settings
Performing a reset from the receiver restores the factory settings and
configures the Shure Control and Dante IP address mode to AUTO.
1. From the receiver menu: DEVICEUTILITIES > SYSTEMRESET >
RESTOREDEFAULTSETTINGS 2. Press ENTER to complete the reset.
Restoring the Dante Network Card Factory Settings
The FactoryReset option within the Dante controller restores the Dante card to
the factory settings and configures the Dante IP address mode to AUTO.
1. From the Dante controller, select a receiver and open the NetworkConfig
tab. 2. Click on FactoryReset. 3. Allow the Dante controller to refresh before
making any additional changes.
43/64
Shure Incorporated
System Reset
System Reset clears the current receiver settings and restores the factory
default settings. To restore factory default settings:
1. Go to DEVICEUTILITIES > SYSTEMRESET > RESTORE. 2. Scroll to the
DEFAULTSETTINGS option and press ENTER. 3. Press the flashing ENTER button to
return the receiver to the default settings.
Firmware
Firmware is embedded software in each component that controls functionality.
Periodically, new versions of firmware are devel oped to incorporate
additional features and enhancements. To take advantage of design
improvements, new versions of the firmware can be uploaded and installed using
the Shure Update Utility tool available on the Shure Update Utility page.
Firmware Versions
When updating receiver firmware, update transmitters to the same firmware
version to ensure consistent operation. The firmware of all ULX-D devices has
the form of MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all ULX-D devices
on the network (including transmitters), must have the same MAJOR and MINOR
firmware version numbers (e.g., 1.2.x).
Updating the Receiver
CAUTION! Ensure that receiver power and network connections are maintained
during a firmware update. Do not turn off the receiver until the update is
complete. IMPORTANT! Receivers running firmware prior to 1.4.8 must be updated
to 1.4.8 before updating to newer versions. Re ceivers running firmware
between 1.4.8 and 2.0.28 must be updated to 2.0.28 before updating to newer
versions. See the ULX-D Firmware Update and Issues FAQ for more information on
this update procedure. Once the download is complete, the receiver
automatically begins the firmware update, which overwrites the existing
firmware.
1. Open the Shure Update Utility. 2. Click the Check for Updates button (for
example, 5UpdatesAvailable) to view new firmware versions available to down
load. 3. Select the updates and click Download. The new downloads are added to
the Firmware tab, making them available to
install on the device hardware. 4. Connect the receiver and computer to the
same network. 5. If your receiver has firmware older than 2.0.28 installed on
it, refer to the ULX-D Firmware Update and Issues FAQ for
specific instructions. 6. From the UpdateDevices tab, send the latest firmware
to the receiver.
44/64
Shure Incorporated
Once the transfer is complete, the receiver automatically begins the firmware
update, which overwrites the existing firmware. For more information on the
Shure Update Utility, visit the Shure Update Utility user guide.
Updating the Transmitter
1. Place the transmitter on a microphone or music stand, and roughly align
the stand so that the transmitter’s IR window can be aligned with the
receiver. Shure does not recommend holding the transmitter during the update.
2. To upload the firmware to the transmitter, go to DEVICEUTILITIES >
TXFWUPDATE on the receiver. 3. Align the IR ports. 4. Press ENTER on the
receiver to begin the download to the transmitter. IR ports must be aligned
for the entire down
load, which can take 50 seconds or longer.
Connecting to an External Control System
The ULX-D receiver is compatible with external control systems such as AMX or
Crestron via the Ethernet, using on the same cables used to carry Shure
Control (Wireless Workbench). Use only one controller per system to avoid
messaging conflicts.
· Connection: Ethernet (TCP/IP; ULX-D receiver is the client) · Port: 2202 For
a comprehensive list of ULX-D command strings, see the Shure ULX-D command
string FAQ page.
Setting the Gateway to Allow Cross Subnet Routing
ULX-D receivers include gateway addressing to support cross-subnet routing.
The gateway setting allows a single controller to manage devices assigned to
different subnets such as multiple rooms or multiple buildings.
Note: A gateway address is an advanced network setting. In most network
configurations, the setting does not need to be changed.
To set the receiver gateway: 1. From the receiver menu: DEVICEUTILITIES >
NETWORK > SHURECONTROL > NETWORK 2. Press and turn the control wheel to set
the Mode to Manual. 3. Press the control wheel to navigate to the first digit
of the GW (gateway) setting. 4. Turn the control wheel to change a value,
press the control wheel to advance to the next octet. 5. When finished, press
ENTER to save.
Note: When setting the gateway address, the IP address and subnet must be set
to valid addresses.
Managing Your System with Shure Software
Wireless Workbench®
Manage every facet of wireless system performance, from preshow planning to
live channel monitoring, with Wireless Work bench.
· Visit the Wireless Workbench page to download Workbench. · Visit the
Workbench help page to learn how to use Workbench with your system.
45/64
Shure Incorporated
ShurePlusTM Channels Application
Monitor the key elements of your wireless operation on a mobile device over
Wi-Fi with ShurePlus Channels. Use alongside Wireless Workbench or as a stand-
alone application for less complex coordination needs.
· Visit the Channels page to download ShurePlus Channels. · Visit the Channels
user guide to learn how to use Channels with your system.
Troubleshooting
Issue No Sound
See Solution…
Power, Cables, Radio Frequency, or Encryp tion Mismatch
Faint sound or distortion
Gain
Lack of range, unwanted noise bursts, or dropouts
RF
Cannot turn transmitter off or change frequency settings, or can’t program receiver
Interface Locks
Encryption Mismatch message
Encryption Mismatch
Firmware Mismatch message
Firmware Mismatch
Antenna Fault message
RF
Tx Battery Hot message
Tx Battery Hot
Power
Make sure that the receiver and transmitter are receiving sufficient voltage.
Check the battery indicators and replace the trans mitter batteries if
necessary.
Gain
Adjust the system gain on the front of the receiver. Ensure the output level
(XLR output only) on the back of the receiver corre sponds to the input of the
mixing console, amplifier, or DSP.
Cables
Check that all cables and connectors are working correctly.
Interface Locks
The transmitter and the receiver can be locked to prevent accidental or
unauthorized changes. A locked feature or button will produce the Locked
screen on the LCD panel.
Encryption Mismatch
Re-sync all receivers and transmitters after enabling or disabling encryption.
46/64
Shure Incorporated
Firmware Mismatch
Paired transmitters and receivers must have the same firmware version
installed to ensure consistent operation. See the Firmware topic for firmware
update procedure.
Tx Battery Hot
If the transmitter battery does not cool off, the transmitter will shut down.
Let the device cool down and then consider swapping the transmitter battery to
continue operation. Identify any possible external heat sources to the
transmitter and operate the transmitter away from those external heat sources.
All batteries should be stored and operated away from external heat sources in
reasonable temperature conditions for best performance.
Radio Frequency (RF)
RF LEDs
If neither blue RF Diversity LED is illuminated, then the receiver is not
detecting the presence of a transmitter. The amber RF Signal Strength LEDs
indicate the amount of RF power being received. This signal could be from the
transmit ter, or it could be from an interfering source, such as a television
broadcast. If more than one or two of the amber RF LEDs are still illuminated
while the transmitter is off, then that channel has too much interference, and
you should try a differ ent channel. The red RF LED indicates RF overload.
This will usually not cause a problem unless you are using more than one
system at the same time, in which case, it can cause interference in the other
system.
Compatibility
· Perform a Scan and Sync to ensure the transmitter and receiver are set to
the same group and channel. · Look at the label on the transmitter and
receiver to make sure they are in the same band (G50, J50, L50, etc…).
Reducing Interference
· Perform a group or channel scan to find the best open frequency. Perform a
sync to transfer the setting to the transmitter. · For multiple systems, check
that all systems are set to channels in the same group (systems in different
bands do not
need to be set to the same group). · Maintain a line of sight between
transmitter and receiver antennas. · Move receiver antennas away from metal
objects or other sources of RF interference (such as CD players, computers,
digital effects, network switches, network cables and Personal Stereo Monitor
(PSM) wireless systems). · Eliminate RF overload (see below).
Increasing Range
If the transmitter is more than 6 to 60 m (20 to 200 ft) from the receiver
antenna, you may be able to increase range by doing one of the following:
· Reduce interference (see above). · Increase transmitter RF power level. ·
Use Normal mode instead of High Density mode. · Use an active directional
antenna, antenna distribution system, or other antenna accessory to increase
RF range.
47/64
Eliminating RF Overload
If you see the red RF LED on a receiver, try the following:
· Reduce the transmitter RF power level · Move the transmitter further away
from the receiver–at least 6 m (20 ft) · If you are using active antennas,
reduce antenna or amplifier gain. · Use omnidirectional antennas
Antenna Faults
The AntennaFault message indicates a short circuit condition at an antenna
port.
· Check antennas and cables for damage · Ensure that antenna ports are not
overloaded · Check antenna bias voltage setting. Turn off voltage if using
passive antennas.
Contact Customer Support
Didn’t find what you need? Contact our customer support to get help.
Accessories
Furnished Accessories
All Systems
Receiver 1/2-Wave Receiver Antennas (2) Hardware Kit (Rack mounting Screws) 22
in. BNC-BNC Coaxial Cable (2) Bulkhead Adapter (2) Ethernet Cable 3 ft.
Handheld Systems
Handheld Transmitter Cartridge Microphone Clip Zipper Bag AA alkaline
batteries (2)
ULXD4D, ULXD4Q frequency band dependent 90XN1371 95K2035 95A8994 95B15103
ULXD2 see options below 95T9279 95B2313 80B8201
Shure Incorporated 48/64
Shure Incorporated
Battery Contact Cover
65A15947
Choice of one (1) of the following:
SM58 SM86 SM87A Beta 58A Beta 87A Beta 87C KSM8 Nickel KSM8 Black KSM9 KSM9HS
Bodypack System
Bodypack Transmitter 1/4-Wave Transmitter Antennas Zipper Bag AA batteries (2)
RPW112 RPW114 RPW116 RPW118 RPW120 RPW122 RPW170 RPW174 RPW184 RPW186
ULXD1 frequency band dependent 95A2313 80B8201
Choice of one (1) of the following:
Cable, Instrument, 2.5 foot (.75 m), 4 Pin Mini Connector (TA4F) WA302
to 1/4-inch Connector.
Instrument Clip-on microphone
Beta 98H/C
Lavalier microphone
MX150, MX153, WL183, WL184, WL185
Headset microphone
WH30TQG
Cable, Instrument, 2-foot (0.7m), 4-pin Mini Connector (TA4F) with Right-Angle 1/4-inch Connector, used with Shure Wireless Bodypack Transmitters
WA304
Premium Guitar Cable TQG Latching Connector
WA306
Premium 1/4″ Right-Angle
WA307
LEMO to 1/4″
WA308
49/64
Shure Incorporated
LEMO to 1/4″ Right-Angle
WA309
Antennas
Band G50 G51 G52 H51 H52 J50 K51 L50 L51 P51 R51 AB Q51
1/2-Wave Receiver Antennas 95AA9279 95AA9279 95AA9279 95AL9279 95AL9279 95AK9279 95AJ9279 95AD9279 95AD9279 95AF9279 95M9279 95M9279 95M9279
1/4-Wave Transmitter Antennas 95G9043 (Yellow) 95G9043 (Yellow) 95G9043 (Yellow) 95D9043 (Gray) 95D9043 (Gray) 95E9043 (Black) 95E9043 (Black) 95E9043 (Black) 95E9043 (Black) 95F9043 (Blue) 95F9043 (Blue) N/A N/A
Optional Accessories
Shure Lithium-Ion Rechargeable Battery. 8-Bay Shure Battery Charger Dual
Docking Charger, Power Supply Not Included Boundary Transmitter ULXD Gooseneck
Base Transmitter 4-bay networked docking station for gooseneck and boundary
microphones 8-bay networked docking station for gooseneck and boundary
microphones Carrying Case Black Bodypack Pouch Y-Cable for bodypack
transmitters Antenna Distribution System Passive Antenna/Splitter Combiner Kit
(recommended for 2 receivers)
SB900B SBC800 SBC200 ULXD6 ULXD8 SBC450 SBC850 WA610 WA582B AXT652 UA845SWB UA221
50/64
Shure Incorporated
In-Line Antenna Amplifier, 470-698MHz
UA830USTV
UHF Antenna Power Distribution Amplifier (recommended for 3 or more receivers)
UA844SWB
In-Line Power Supply
UABIAST
Front Mount Antenna Kit (Includes 2 Cables And 2 Bulkhead)
UA600
1/2 Wave Antenna Remote Mount Kit
UA505
Active Directional Antenna 470-900MHZ
UA874WB
Passive Directional Antenna 470-952 MHz. Includes 10 foot BNC to BNC cable.
PA805SWB
2 ft. BNC-BNC Coaxial Cable
UA802
6 foot (1.8m) BNC to BNC Coaxial Cable for Remote Antenna Mounting for ULX Wireless System
UA806
25 ft. BNC-BNC Coaxial Cable
UA825
50 ft. BNC-BNC Coaxial Cable
UA850
100 ft. BNC-BNC Coaxial Cable
UA8100
Specifications
ULX-D System Specifications
RF Carrier Frequency Range
470932 MHz, varies by region (See Frequency Range and Output Power table)
Working Range
100 m ( 330 ft)
Note: Actual range depends on RF signal absorption, reflection and
interference.Note: Actual range depends on RF signal ab sorption, reflection
and interference.
RF Tuning Step Size
25 kHz, varies by region
Image Rejection
70 dB, typical
RF Sensitivity
-98 dBm at 10-5 BER
Latency
<2.9 ms
51/64
Shure Incorporated
Audio Dynamic Range
A-weighted, typical, System Gain @ +10
XLR Analog Output
Dante Digital Output
Total Harmonic Distortion
-12 dBFS input, System Gain @ +10
<0.1%
120 dB 130 dB
System Audio Polarity
Positive pressure on microphone diaphragm produces positive voltage on pin 2
(with respect to pin 3 of XLR output) and the tip of the 6.35 mm (1/4-inch)
output.
Operating Temperature Range
-18°C (0°F) to 50°C (122°F)
Note: Battery characteristics may limit this range.
Storage Temperature Range
-29°C (-20°F) to 74°C (165°F)
Note: Battery characteristics may limit this range.
ULXD4D & ULXD4Q
ULXD4D Weight
3.36 kg (7.4 lbs), without antennas
Power Requirement
100 to 240 V AC, 5060 Hz, 0.26 A max.
ULXD4Q
Weight
3.45 kg (7.6 lbs), without antennas
Power Requirement
100 to 240 V AC, 5060 Hz, 0.32 A max.
ULXD4D & ULXD4Q
Dimensions
44 x 482 x 274 mmH x W x D
Housing
steel; Extruded Aluminum
52/64
Shure Incorporated
Audio Output
Gain Adjustment Range
-18 to +42 dB in 1 dB steps (plus Mute setting)
Configuration
XLR
Impedance
100
balanced (1=ground, 2=audio +, 3=audio -)
Full Scale Output
LINE setting
MIC setting
Mic/Line Switch
30 dB pad
+18 dBV -12 dBV
Phantom Power Protection
Yes
Cascade Output
Connector Type
BNC
Note: For connection of one additional receiver in the same band
Configuration
Unbalanced, passive
Impedance
50
Insertion Loss
0 dB
Networking
Network Interface
Dual Port Ethernet 10/100 Mbps, 1Gbps, Dante Digital Audio
Network Addressing Capability
DHCP or Manual IP address
Maximum Cable Length
100 m (328 ft)
53/64
RF Input
Spurious Rejection
80 dB, typical
Connector Type
BNC
Impedance
50
Bias Voltage
12 to 13 V DC, 150 mA maximum, per antenna
switchable on-off
ULXD1
Mic Offset Range
0 to 21 dB (in 3 dB steps)
Audio Frequency Response
20 20 kHz (±1 dB)
Battery Type
Shure SB900B Rechargeable LiIon or LR6 AA batteries 1.5 V
Battery Runtime
@ 10 mW Shure SB900B
alkaline
See Battery Runtime Chart
Dimensions
86 mm x 66 mm x 23 mm (3.4 in. x 2.6 in. x 0.9 in.) H x W x D
Weight
142 g (5.0 oz.), without batteries
Housing
Cast aluminum
Audio Input
Connector
4-Pin male mini connector (TA4M), See drawing for details
Configuration
Unbalanced
Impedance
1 M, See drawing for details
8 hours 9 hours
Shure Incorporated 54/64
Maximum Input Level
1 kHz at 1% THD Pad Off
Pad On
Preamplifier Equivalent Input Noise (EIN)
System Gain Setting +20120 dBV, Aweighted, typical
8.5 dBV ( 7.5 Vpp) 20.5 dBV ( 30 Vpp)
RF Output
Connector
SMA
Antenna Type
1/4 wave
Impedance
50
Occupied Bandwidth
<200 kHz
Modulation Type
Shure proprietary digital
Power
1 mW, 10 mW, 20 mW
See Frequency Range and Output Power table, varies by region
ULXD2
Mic Offset Range
0 to 21 dB (in 3 dB steps)
Audio Frequency Response
Note: Dependent on microphone type
Battery Type
Shure SB900B Rechargeable LiIon or LR6 AA batteries 1.5 V
Battery Runtime
@ 10 mW
Shure SB900B
alkaline
8 hours 9 hours
See Battery Runtime Chart
Dimensions
VHF V50 and V51 Other frequency bands
Weight
VHF V50 and V51
278 mm x 51 mm (10.9 in. x 2.0 in.) L x Dia. 256 mm x 51 mm (10.1 in. x 2.0
in.) L x Dia.
348 g (12.3 oz.), without batteries
Shure Incorporated 55/64
Other frequency bands
Housing
Machined aluminum
340 g (12.0 oz.), without batteries
Audio Input
Configuration
Unbalanced
Maximum Input Level
1 kHz at 1% THD145 dB SPL (SM58), typical
Note: Dependent on microphone type
RF Output
Antenna Type
Integrated Single Band Helical
Occupied Bandwidth
<200 kHz
Modulation Type
Shure proprietary digital
Power
1 mW, 10 mW, 20 mW
See Frequency Range and Output Power table, varies by region
Tables and Diagrams
TA4M Connector
Shure Incorporated
56/64
LEMO Connector
Shure Incorporated
XLR to ¼ Output
Use the following wiring diagram to convert the XLR output to a ¼ output.
Batteries
ULXD Battery Life
hours
MHz
SB900B
alkaline
470 to 810
1/10 mW >8:30
20 mW >5:40
1/10 mW >8
20 mW >5:30
902 to 928
7:30
4:40
7
4
174 to 216
8:30
6:35
8
5
1240 to 1800
8
6:05
6
4:30
Note: The SB900B Shure rechargeable battery uses SBC200, SBC800 and SBC220
chargers.
The values in this table are typical of fresh, high quality batteries. Battery
runtime varies depending on the manufacturer and age of the battery.
Frequency Range and Transmitter Output Power
Band
Frequency Range ( MHz )
Power ( mW RMS )* (Lo/Nm/Hi)
G50
470 to 534
1/10/20
G51
470 to 534
1/10/20
57/64
Band
G52 G53 G62 H50 H51 H52 J50 J50A J51 K51 L50 L51 L53 M19 P51 R51 JB (Tx only)
AB (Rx and Tx)
Q12 Q51 V50 V51 V52 X50 X51 X52 X53
Frequency Range ( MHz )
479 to 534 470 to 510 510 to 530 534 to 598 534 to 598 534 to 565 572 to 636
572 to 608 572 to 636 606 to 670 632 to 696 632 to 696 632 to 714 694 to 703
710 to 782 800 to 810 806 to 810
770 to 810
748 to 758 794 to 806 174 to 216 174 to 216 174 to 210 925 to 932 925 to 937.5
902 to 928 902 to 907.500, 915 to 928
Power ( mW RMS )* (Lo/Nm/Hi)
1/10 1/10/20 1/10/20 1/10/20 1/10/20 1/10 1/10/20 1/10/20 1/10/20 1/10 1/10/20
1/10/20 1/10/20 1/10/20 1/10/20 1/10/20 1/10 A Band (770-805): 1/10/20 B Band
(806-809): 1/10 1/10/20 10 1/10/20 1/10/20 10 1/10 10 0.25/10/20 0.25/10/20
Shure Incorporated 58/64
Shure Incorporated
Band
Frequency Range ( MHz )
Power ( mW RMS )* (Lo/Nm/Hi)
X54
915 to 928
0.25/10/20
Z16
1240 to 1260
1/10/20
Z17
1492 to 1525
1/10/20
Z18
1785 to 1805
1/10/20
Z19
1785 to 1800
1/10/20
Z20
1790 to 1805
1/10/20
Output power limited to 10 mW above 608 MHz.
Note: Frequency bands might not be available for sale or authorized for use in
all countries or regions.
- Power delivered to the antenna port
For the band Z17 (1492-1525 MHz), it must be used indoors only.
For the Band Z19 (17851800MHz) used in Australia, per Radio Communications Low
Interference Potential Devices Class Li cense 2015; item 30 note C: the system
must be operated within the range of 1790-1800MHz when used outdoors.
.
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings.
4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN
ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow
sufficient distances for adequate ventilation and install in accordance
with the manufacturer’s instructions. 8. DO NOT install near any heat sources
such as open flames, radiators, heat registers, stoves, or other apparatus (in
cluding amplifiers) that produce heat. Do not place any open flame sources on
the product. 9. DO NOT defeat the safety purpose of the polarized or grounding
type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third
grounding prong. The wider blade or the third
59/64
Shure Incorporated
prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replace ment of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long
periods of time. 14. REFER all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any
way, such as power supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped. 15. DO NOT expose
the apparatus to dripping and splashing. DO NOT put objects filled with
liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance
coupler shall remain readily operable. 17. The airborne noise of the Apparatus
does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be
connected to a MAINS socket outlet with a protective earthing connec tion. 19.
To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture. 20. Do not attempt to modify this product. Doing so could
result in personal injury and/or product failure. 21. Operate this product
within its specified operating temperature range. Explanation of Symbols
Caution: risk of electric shock Caution: risk of danger (See note.) Direct
current Alternating current
On (Supply)
Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION
Stand-by
Equipment should not be disposed of in the normal waste stream
WARNING: Voltages in this equipment are hazardous to life. No userserviceable
parts inside. Refer all servicing to qualified service personnel. The safety
cer tifications do not apply when the operating voltage is changed from the
factory setting. WARNING: Danger of explosion if incorrect battery replaced.
Operate only with AA batteries. Note: Use only with the included power supply
or a Shure-approved equivalent.
60/64
Shure Incorporated
WARNING
· Battery packs may explode or release toxic materials. Risk of fire or burns.
Do not open, crush, modify, disassemble, heat above 140°F (60°C), or
incinerate.
· Follow instructions from manufacturer · Only use Shure charger to recharge
Shure rechargeable batteries · WARNING: Danger of explosion if battery
incorrectly replaced. Replace only with same or equivalent type. · Never put
batteries in mouth. If swallowed, contact your physician or local poison
control center · Do not short circuit; may cause burns or catch fire · Do not
charge or use battery packs other than Shure rechargeable batteries · Dispose
of battery packs properly. Check with local vendor for proper disposal of used
battery packs. · Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like · Do not immerse
the battery in liquid such as water, beverages, or other fluids. · Do not
attach or insert battery with polarity reversed. · Keep away from small
children. · Do not use abnormal batteries. · Pack the battery securely for
transport.
Important Product Information
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be required in
certain areas. Consult your national authority for possible requirements.
Changes or modifications not expressly approved by Shure Incorporated could
void your authority to operate the equipment. Licensing of Shure wireless
microphone equipment is the user’s responsibility, and licensability de pends
on the user’s classification and application, and on the selected frequency.
Shure strongly urges the user to contact the appropriate telecommunications
authority concerning proper licensing, and before choosing and ordering
frequencies.
Information to the user
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept
any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installa tion. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation
between the equipment and the receiver. · Connect the equipment to an outlet
on a circuit different from that to which the receiver is connected. · Consult
the dealer or an experienced radio/TV technician for help.
Note: EMC conformance testing is based on the use of supplied and recommended
cable types. The use of other cable types may degrade EMC perfor mance.
Please follow your regional recycling scheme for batteries, packaging, and
electronic waste.
61/64
Shure Incorporated
Australia Warning for Wireless
This device operates under an ACMA class licence and must comply with all the
conditions of that licence including operating frequencies. Before 31 December
2014, this device will comply if it is operated in the 520-820 MHz frequency
band. WARNING: After 31 December 2014, in order to comply, this device must
not be operated in the 694-820 MHz band.
Certifications
Meets essential requirements of the following European Directives:
· WEEE Directive 2012/19/EU, as amended by 2008/34/EC · RoHS Directive EU
2015/863
Note: Please follow your regional recycling scheme for batteries and
electronic waste
This product meets the Essential Requirements of all relevant European
directives and is eligible for CE marking. CE Notice: Hereby, Shure
Incorporated declares that this product with CE Marking has been determined to
be in compliance with European Union requirements. The full text of the EU
declaration of conformity is available at the following site: https://
www.shure.com/en-EU/support/declarations-of-conformity. Authorized European
representative: Shure Europe GmbH Department: Global Compliance Jakob-
Dieffenbacher-Str. 12 75031 Eppingen, Germany Phone: +49-7262-92 49 0 Fax:
+49-7262-92 49 11 4 Email: EMEAsupport@shure.de Certified under FCC Part 15
and FCC Part 74. Certified by ISED in Canada under RSS-102 and RSS-210. IC:
616A-ULXD1 G50, 616A-ULXD1 H50, 616A-ULXD1 J50, 616A-ULXD1 L50; 616A-ULXD2
G50, 616A-ULXD2 H50, 616AULXD2 J50, 616A-ULXD2 L50, 616A-ULXD1G50S, 616A-
ULXD1H50S, 616A-ULXD1J50AS, 616A-ULXD2G50S, 616AULXD2H50S, 616A-ULXD2J50AS.
FCC: DD4ULXD1G50, DD4ULXD1H50, DD4ULXD1J50, DD4ULXD1L50; DD4ULXD2G50,
DD4ULXD2H50, DD4ULXD2J50, DD4ULXD2L50, DD4ULXD1-G50, DD4ULXD1-H50,
DD4ULXD1-J50A, DD4ULXD1-X52, DD4ULXD2-G50, DD4ULXD2-H50, DD4ULXD2-J50A,
DD4ULXD2-X52 . IC: 616A-ULXD1X52, 616A-ULXD2X52 FCC: DD4ULXD1X52, DD4ULXD2X52
IC: 616A-ULXD1V50, 616A-ULXD2V50 FCC: DD4ULXD1V50, DD4ULXD2V50
Note: For transmitters operating in the V50 and V51 bands: nominal free space
antenna gain at middle of the band is typically -6 dBi, and rolls off at the
band edges an additional -4 dB.
Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.
Conforms to electrical safety requirements based on IEC 60065. “”
62/64
Shure Incorporated
ISM
Information to the user
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference. 2. This device must accept
any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installa tion. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation
between the equipment and the receiver. · Connect the equipment to an outlet
on a circuit different from that to which the receiver is connected. · Consult
the dealer or an experienced radio/TV technician for help.
This device operates on frequencies shared with other devices. Consult the
Federal Communications Commission White Space Database Administration website
to determine available channels in your area prior to operation. No
useroperated control of power, frequency, or other parameters are available
beyond those specified in this operating man ual.
Canada Warning for Wireless
This device operates on a noprotection, nointerference basis. Should the user
seek to obtain protection from other radio ser vices operating in the same TV
bands, a radio licence is required. For further details, consult Innovation,
Science and Econom ic Development Canada’s document Client Procedures Circular
CPC2128, Voluntary Licensing of LicenceExempt LowPow er Radio Apparatus in the
TV Bands. Ce dispositif fonctionne selon un régime de nonbrouillage et de
nonprotection. Si l’utilisateur devait chercher à obtenir une certaine
protection contre d’autres services radio fonctionnant dans les mêmes bandes
de télévision, une licence radio serait requise. Pour en savoir plus, veuillez
consulter la Circulaire des procédures concernant les clients CPC2128,
Délivrance de licences sur une base volontaire pour les appareils radio de
faible puissance exempts de licence et exploités dans les bandes de télévision
d’Innovation, Sciences et Développement économique Canada. This device
contains licenceexempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Develop ment Canada’s licenceexempt RSS(s). Operation is
subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any
interference, including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
63/64
Shure Incorporated 2. L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
64/64
References
- Audinate - Pioneering the future of AV
- Shure: Microphones, Wireless microphones, in-ear monitoring, earphones, headphones
- Documentation Finder - Shure Europe
- Wireless Workbench 7 - WWB7 - Shure USA
- null - Shure
- ShurePlus MOTIV
- Service
- Service
- Service
- ShurePlus™ Channels - Channels Mobile App for iOS and Android - Shure USA
- SUU - Shure Update Utility - Shure USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>