MASTER DYNAMIC MW40 Wireless Over-Ear Headphones User Guide
- June 9, 2024
- MASTER DYNAMIC
Table of Contents
MASTER DYNAMIC MW40 Wireless Over-Ear Headphones User Guide
POWERING ON
Press Power/Pairing button once to power ON/OFF. Battery level will be displayed at startup. Before listening, charge your headphones for at least 15 minutes and download the M &D Connect App to check for firmware updates.
To conserve battery power, headphones will power OFF after 30 minutes of inactivity. This setting can be adjusted in the M &D Connect app.
PAIRING
The first time you power ON your headphones they will enter pairing mode. Simply connect through the Bluetooth menu on your device and select M &D MH40W.
To manually activate pairing mode, hold Power/Pairing button for 4 seconds.
Download the M &D Connect App for the complete Master & Dynamic experience.
Use the M &D Connect App to access:
FUNCTIONS
White light will pulse when headphones are in pairing mode.
A solid white light indicates you are connected.
High Battery
Med Battery
Low Battery
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development de Canada’s license- exempt RSS(s). Operation is subject tothe following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS‐102 radiation exposure limits set forth for an uncontrolled environment.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
- To prevent possible hearing damage, do not listen at high volume levels for long periods.
- Fully understand user manual before use.
- Ensure your player at low volume levels or power off before you leave.
CAUTION:
To avoid replacement of a battery with an incorrect type Don’t disposal of a
battery into fire or a hot oven, or mechanically crushing or cutting of a
Battery. Don’t leaving a battery in an extremely high temperature surrounding
environment to avoid battery subjected to extremely low air pressure.
- Bluetooth: 2402MHz – 2480MHz @9.31 dBm
- Headphone Input: 5.0V, 350mA;
Working Temperature: 0-45 degrees
This product is in line with the basic requirements of regulation Radio Equipment Regulations 2017 and further relevant regulations
To avoid risk of fire, the equipment is supplied only by external power source of which output shall comply with PS1 (with output capacity less than 15W)
Hereby, NEW AUDIO LLC. declares that the radio equipment type MH40-W2 is in compliance with Directive 2014/53/EU and European Safety Regulations. The full text of the EU declaration of conformity is available at the following internet address: https://www.masterdynamic.com
PRODUCT COMPLIES WITH EUROPEAN SAFETY REGULATIONS
ENVIRONMENTALLY FRIENDLY DISPOSAL
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collection point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substance.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLANCED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCATIONS.
References
- Product Support | Master & Dynamic
- Professional Headphones & Luxury Earphones | Master & Dynamic Official
- Professional Headphones & Luxury Earphones| Master & Dynamic Official | Master & Dynamic
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>