TITAN HGC702000 TALI 3-IN-1 VPD Sensor Instruction Manual

TITAN HGC702000 TALI 3-IN-1 VPD Sensor

FC

This device complies with Part 18 of the FCC Rules. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.45-30 MHz. A simple measure to correct interference is to add ferrites to the ends of lengths of communication cables.

Scan for the most up-to-date instructions

LIMITATION OF LIABILITY

DD NOT PLATE, ENGRAVE, OR PROCEED TO PRESS WITH THIS FILE WITHOUT PROPER INSPECTION
All files and proofs must be thoroughly inspected by the recipient immediately upon receipt. It is the responsibility of the recipient to examine and proofread all files and proofs. In the event file{s) and/or proof{s) are found to be incorrect upon inspection, call 513-281-0999 and ask for the separation contact. The liability of

Olberding Brand Family shall
be limited to correcting and replacing the materials that we supplied that were found to be defective. Olberding Brand Family will not be liable for any other loss or damage including, but not limited to, cost of Flexor printing plates that we did not make, print cylinders, inks, substrates/printed materials, and/or make ready and press time.

Tali 3-in-1 VPD Sensor – Overview

Thank you for purchasing the Titan Controls Tali 3-in-1 VPD sensor. Before use, please check if the HGC702000-VPD sensor is in good condition. We recommend that you read the HGC702000-VPD manual carefully before installation. This sensor is designed to monitor the temperature, humidity and air pressure in your growing environment. From these readings, the sensor will be able to calculate your VPD (vapor pressure deficit). Understanding the VPD level in your room will help you to optimize your plant’s growth. In the process of growing, your plant absorbs water, nutrients, and carbon dioxide from the atmosphere through transpiration. If the transpiration is too strong, the water absorption rate of the root system will not keep up with the evaporation rate and the plant will lose water and wilt. On the other hand, too little water evaporation will cause the soil moisture to be too high, which will not allow oxygen to circulate. This will cause the roots to be blocked, which results in reduced nutrient and carbon dioxide intake. Keep the plant’s transpiration within a good range to get the best growth. For the procedures of planting, cutting, grafting, and transplantation, maintaining excellent transpiration is the key to maintaining a healthy plant.

WARNING:
Misuse or improper protection installation may damage the sensor and may invalidate the manufacturer’s warranty. To integrate the Titan Controls Tali VPD sensor into your system, please follow the recommended installation instructions and be equipped with appropriate protection devices to protect the sensor from damage.
If installing a sensor in a lightning-prone area with a grounded data logger, please refer to the application note Lightning Impulse and Grounding Practices.

Installation

1. Install sensor(s) into desired positions following the recommended method (see installation method)
2. Once the sensor(s) has been put into position, connect the sensor cable to the controller (see connecting to EL3)
3. After your sensor(s) have been connected to the EL3, you will be able to locate them on the “Sensor List” screen
   • All sensors will default to the “Zone A” grouping. This can be changed by selecting a sensor and tapping on the icon. From here you can switch between “Zone A” and “Zone B”
   • You can also select which sensor you want to be the “default” sensor that is shown on the home screen, by tapping on the sensor card and check “Home page display”

THIS PAGE PRINTS AT 00% REDUCTION OF THE ORIGINAL LABEL TO FIT ON 11” x 17” PAGE.

LIMITATION OF LIABILITY
DO NOT PLATE, ENGRAVE, OR PROCEED TO PRESS WITH THIS FILE WITHOUT PROPER INSPECTION All files and proofs must be thoroughly Inspected by the recipient Im med lately upon receipt. It Is the responsibly of the redolent to examine and proofread all files and proofs. In the event file(s) and/or proof{s) are found to be Incorrect upon Inspection, call 513·281·0999 and askforthe separation contact. The llablllty of Olberding Brand Family shall
be limited to correcting and replacing the materials that we supplied that were found to be defective. Olberding Brand Family will not be Hamble for any other loss or damage lndudlng, but not limited to, cost of Flex printing plates that we did not make, print cylinders, Inks, substrates/printed materials, and/or make ready and press time.

Product Appearance

In Box

THIS PAGE PRINTS AT 00% REDUCTION OF THE ORIGINAL LABEL TO FIT ON 11” x 17” PAGE.

LIMITATION OF LIABILITY
DO NOT PLATE, ENGRAVE, OR PROCEED TO PRESS WITH THIS FILE WITHOUT PROPER INSPECTION All files and proofs must be thoroughly Inspected by the recipient im med lately upon receipt. It Is the responsibly of the redolent to examine and proofread all files and proofs. In the event file(s) and/or proof{s) are found to be Incorrect upon Inspection, call 513·281·0999 and askforthe separation contact. The llablllty of  Olberding Brand Family shall
be limited to correcting and replacing the materials that we supplied that were found to be defective. Olberding Brand Family will not be Hamble for any other loss or damage lndudlng, but not limited to, cost of Flexo printing plates that we did not make, print cylinders, Inks, substrates/printed materials, and/or make ready and press time.

Description of material and size

Cover material| PC
Cover sheath| PVC| Cable inner core| Oxygen-free copper
Dimension| 83mm L x 55mm W x 122mm H

Product Parameter

Performance parameter

Power| ≤0.8W
Power supply| 6 – 24V DC
Operation temperature range| 32° F – 122° F
Operation humidity range| ≤95%RH
Min time interval for data reporting| <8 S
Interface protocol| CAN bus
Communication rate| 50Kbps
 |

Compliance

| UL61010-1 CSA C22.2 #61010-1-12

FCC Part 18

Function parameter
Interface protocol| CAN Bus
Screen resolution| 240*320

Accuracy

Sensor Specification| Measuring Range| Accuracy
Temperature| 0° C ~ 50° C| ±0.5° C
Relative Humidity| 0%RH ~ 95%RH| ±5%RH

THIS PAGE PRINTS AT 100% REDUCTION OF THE ORIGINAL LABEL TO FIT ON 11” x 17” PAGE.

LIMITATION OF LIABILITY
DO NOT PLATE, ENGRAVE, OR PROCEED TO PRESS WITH THIS FILE WITHOUT PROPER INSPECTION All files and proofs must be thoroughly Inspected by the recipient immediately upon receipt. It Is the responsibly of the redolent to examine and proofread all files and proofs. In the event file(s) and/or proof{s) are found to be Incorrect upon Inspection, call 513·281·0999 and askforthe separation contact. The llablllty of  Olberding Brand Family shall
be limited to correcting and replacing the materials that we supplied that were found to be defective. Olberding Brand Family will not be Hamble for any other loss or damage lndudlng, but not limited to, cost of Flex printing plates that we did not make, print cylinders, Inks, substrates/printed materials, and/or make ready and press time.

Installation Method And Connecting To EL3

Up to 16 Tail VPD sensors can be connected to the Gravitas EL3. The Titan Controls Tail 3-in-1 VPD sensor needs to be used in a ventilated environment, and the installation position is as shown in the figure. Failure to follow the recommended positioning may result in nonoptimal readings.

THIS PAGE PRINTS AT 100% REDUCTION OF THE ORIGINAL LABEL TO FIT ON 11” x 17” PAGE.

LIMITATION OF LIABILITY
DO NOT PLATE, ENGRAVE, OR PROCEED TO PRESS WITH THIS FILE WITHOUT PROPER INSPECTION All files and proofs must be thoroughly Inspected by the recipient immediately upon receipt. It Is the responsibly of the redolent to examine and proofread all files and proofs. In the event file(s) and/or proof{s) are found to be Incorrect upon Inspection, call 513·281·0999 and askforthe separation contact. The llablllty of  Olberding Brand Family shall
be limited to correcting and replacing the materials that we supplied that were found to be defective. Olberding Brand Family will not be Hamble for any other loss or damage lndudlng, but not limited to, cost of Flex printing plates that we did not make, print cylinders, Inks, substrates/printed materials, and/or make ready and press time.

WARRANTY SERVICE: Please read warranty information first
If after reviewing the troubleshooting tips the unit will still not work, you should return it to the Dealer where you purchased it. They will be able to further evaluate the unit, test various components and possibly identify and/or fix issues. If the Dealer is unable to fix the unit, they will return it to us for factory repair. If there are no Dealers in your area, you may contact us directly for technical support. If we cannot help you resolve the problem over the phone, we will issue you a RMA # (return merchandise authorization) authorizing you to return the unit to us for factory reconditioning (if the unit is under warranty). Contact the number below for a RMA and shipping address. Complete the form below and include it with your unit. Also, please write the RMA # on the outside of the box. Please package the unit in its original packaging. If damaged in shipment, we are not responsible for the unit. Once we receive the unit, we will repair it within 48 hours (business days) and return it to you as freight prepaid via UPS ground shipment.

Include the following if returning directly to Titan Controls

• Proof of purchase
• This completed form
• RMA # on the outside of the box

Return Merchandise Authorization Number (Required) Company Name:
Contact Name:
Address:
Phone #:
Email address:
What is the nature of the problem?

Shipping address will be given when the RMA # is issued:

www.titancontrols.net For technical assistance, call us at 1-888-80-Titan or 1-888-808-4826. Representative available Monday – Friday, 8 a.m. – 5 p.m. PST.

Warranty Information

When purchased from an authorized Hawthorne dealer, this product is covered by a LIMITED WARRANTY available at: hawthornegc.com/warranties. You can also obtain the Terms of Sale and Limited Warranty by calling Hawthorne toll-free at: 1-888-478-6544 or writing Hawthorne at: Hawthorne Hydroponics LLC, 3204 NW 38th Circle, Vancouver, WA 98660, Attn: Customer Service.

Service and Repair Program

• For all service and repairs, please contact one of our Technical Service Representatives for a Return Merchandise Authorization (RMA) number.
• Titan Controls will, at its discretion, repair or replace the sensor.
• Factory calibration services are available for all Titan Controls .
• Returning Units: Please contact your retail store for returns.

THIS PAGE PRINTS AT 100% REDUCTION OF THE ORIGINAL LABEL TO FIT ON 11” x 17” PAGE.

LIMITATION OF LIABILITY
DO NOT PLATE, ENGRAVE, OR PROCEED TO PRESS WITH THIS FILE WITHOUT PROPER INSPECTION All files and proofs must be thoroughly Inspected by the recipient immediately upon receipt. It Is the responsibly of the redolent to examine and proofread all files and proofs. In the event file(s) and/or proof{s) are found to be Incorrect upon Inspection, call 513·281·0999 and askforthe separation contact. The llablllty of  Olberding Brand Family shall
be limited to correcting and replacing the materials that we supplied that were found to be defective. Olberding Brand Family will not be Hamble for any other loss or damage lndudlng, but not limited to, cost of Flex printing plates that we did not make, print cylinders, Inks, substrates/printed materials, and/or make ready and press time.

References

• Home | Titan Controls
• Home | Titan Controls

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>