ASUS PRIME H310M-E R2.0 Motherboard User Manual

ASUS PRIME H310M-E R2.0 Motherboard

E14387
First Edition
June 2018
Copyright © 2018 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if:

1. The product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or
2. The serial number of the product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either

1. for free by downloading it from http://support.asus.com/download
   or

2. for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address [email protected], stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address).

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
• Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.
• Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit.
• Ensure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation safety

• Before installing the motherboard and adding components, carefully read all the manuals that came with the package.
• Before using the product, ensure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may be exposed to moisture.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualified service technician or your retailer.

About this guide
This user guide contains the information you need when installing and configuring the motherboard.
How this guide is organized
This guide contains the following parts:

• Chapter 1: Product introduction
  This chapter describes the features of the motherboard and the new technology it supports. It includes descriptions of the switches, jumpers, and connectors on the motherboard.

• Chapter 2: BIOS information
  This chapter discusses changing system settings through the BIOS Setup menus. Detailed descriptions for the BIOS parameters are also provided.

Where to find more information
Refer to the following sources for additional information and for product and software updates.

1. ASUS websites
   The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.

2. Optional documentation
   Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.

Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

• DANGER/WARNING: Information to prevent injury to yourself when completing a task.
• CAUTION: Information to prevent damage to the components when completing a task.
• IMPORTANT: Instructions that you MUST follow to complete a task.
  NOTE: Tips and additional information to help you complete a task.

Typography

• Bold text Indicates a menu or an item to select.

• Italics Used to emphasize a word or a phrase.

• Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key. Example: means that you must press the Enter or Return key.
• \+ \+ If you must press two or more keys simultaneously, the key names are linked with a plus sign (+).

Package contents

Check your motherboard package for the following items.

• Motherboard ASUS PRIME H310M-E R2.0 motherboard
• Cables 2 x Serial ATA 6.0 Gb/s cables
• Accessories
  • 1 x ASUS I/O Shield
  • 1 x M.2 Anchor
• Application DVD Support DVD
• Documentation User Guide

If any of the above items are damaged or missing, contact your retailer.

PRIME H310M-E R2.0 specifications summary

buffered memory
Dual-channel memory architecture
Supports Intel® Extreme Memory Profile (XMP)

• The maximum memory frequency supported varies by processor.
  ** DDR4 2666MHz and higher memory modules will run at max. 2666MHz on Intel® 8th Gen. 6-core or higher processors.
  * Refer to www.asus.com for the Memory QVL (Qualified Vendors List).
  Expansion slots**|

  • 1 x PCI Express 3.0/2.0 x16 slot (at x16 mode)
  • 2 x PCI Express 2.0 x1 slots

CPU| LGA1151 socket for Intel® 8th Generation Core™ i7 / i5 / i3, Pentium®, and Celeron® processors
Supports Intel® 14nm CPU
Supports Intel® Turbo Boost Technology 2.0** The Intel® Turbo Boost Technology 2.0 support depends on the CPU types.

** Refer to www.asus.com for Intel® CPU support list.

Graphics| Integrated graphics processor – Intel® HD Graphics support Multi-VGA out support: HDMI / D-Sub ports

• Supports HDMI 1.4b output with a maximum resolution of 4096 x 2160 @24Hz / 2560 x 1600@60Hz
• Supports D-Sub output with a maximum resolution of 1920 x 1200 @60Hz
• Supports Intel® InTru™ 3D/Quick Sync Video/Clear Video HD Technology/Insider™ Maximum shared memory of 1024MB

Storage| Intel® H310 Chipset:

• 1 x M.2 Socket 3 with M Key, type 2242/2260/2280 storage devices support (SATA mode & x2 PCIE mode)*

• 4 x SATA 6.0 Gb/s ports (gray)

• When a SATA mode M.2 device is installed, the M.2 Socket shares bandwidth with the SATA6G_2 port.

Due to the Chipset limitation, when an M.2 device is installed in PCIe mode, the socket is set to PCIe 2. 0.**

LAN| Realtek® 8111H Gigabit LAN supports LANGuard

USB

| Intel® H310 Chipset:

• 4 x USB 3.1 Gen 1 (up to 5Gbps) ports (2 ports at mid-board; 2 ports at back
• panel, blue, Type A)
• 6 x USB 2.0/1.1 ports (4 ports at mid-board; 2 ports at back panel)

Audio| Realtek® ALC887 8-channel High Definition Audio CODEC*

Gaming Audio:

• LED-illuminated design: Brighten up your build with the gorgeous illuminated audio trace path

• Audio Shielding: Ensures precision analog/digital separation and greatly reduces multi-lateral interference

• Dedicated audio PCB layers: Separate layers for left and right channels to guard the quality of the sensitive audio signals

• Premium Japanese audio capacitors: Provide warm, natural and immersive sound with exceptional clarity and fidelity

•  Supports jack-detection and front panel jack-retasking

• Choose the chassis with HD audio module in the front panel to support an 8-channel audio output.

ASUS

special features

| ASUS 5X PROTECTION III

• ASUS SafeSlot Core – Fortified PCIe Slot prevents damage
• ASUS LANGuard – Protects against LAN surges, lightning strikes and static – electricity discharges
• ASUS Overvoltage Protection – World-class circuit-protecting power design
• ASUS Stainless Steel Back I/O – 3x corrosion-resistance for greater durability
• ASUS DIGI+ VRM – 4 phase digital power design
• Superb Performance
• M.2 onboard
• The latest transfer technology with up to 10 GB/s data transfer speeds
• ASUS OptiMem
• Improved DDR4 stability
• UEFI BIOS
• The most advanced options with a fast response time
• Gaming Scenario
• Audio Features
• Audio that roars on the battlefield
• ASUS Exclusive Features
• ASUS AI Charger
• ASUS AI Suite 3
• ASUS Anti Surge
• ASUS File Transfer
• ASUS PC Cleaner
• ASUS Q-Design
• ASUS Q-DIMM

ASUS special features

| UEFI BIOS EZ Mode

• Featuring friendly graphics user interface
• ASUS CrashFree BIOS 3
• ASUS EZ Flash 3

ASUS quiet thermal solution| Quiet Thermal Design

• ASUS Fan Xpert
• Stylish Fanless Design: PCH heatsink solution

Rear panel I/O ports|

• 1 x PS/2 keyboard port
• 1 x PS/2 mouse port
• 2 x USB 3.1 Gen 1 (up to 5Gbps) ports (Type-A, blue) 2 x USB 2.0/1.1 ports
• 1 x HDMI port 1 x D-Sub port
• 1 x LAN (RJ-45) port
• 3 x Audio jacks support 8-channel audio output

Internal connectors|

• 1 x USB 3.1 Gen 1 (up to 5Gbps) connector supports additional 2 USB 3.1 Gen 1 ports (19-pin)
• 2 x USB 2.0/1.1 connectors support additional 4 USB 2.0/1.1 ports 4 x SATA 6.0Gb/s connectors
• 1 x 4-pin CPU Fan connector for 4-pin PWM mode
• 1 x 4-pin Chassis Fan connector 4-pin PWM and 3-pin DC mode 1 x COM connector
• 1 x Front panel audio connector (AAFP) 1 x S/PDIF Out connector
• 1 x Speaker connector
• 1 x 24-pin EATX Power connector 1 x 4-pin ATX 12V Power connector 1 x System panel connector
• 1 x TPM connector
• 1 x Clear CMOS jumper (2-pin)

BIOS features

| 128 Mb Flash ROM, UEFI AMI BIOS, PnP, SM BIOS 3.1, ACPI 6.1, Multi-language BIOS, ASUS EZ Flash 3, CrashFree BIOS 3, F6 Qfan Control, F3 My Favorites, Last Modified log, F12 PrintScreen, and ASUS DRAM SPD (Serial Presence Detect) memory information
Manageability| WOL by PME, PXE
Support DVD| Drivers ASUS utilities EZ Update
Anti-virus software (OEM version)
OS support| Windows® 10 (64-bit)
Form factor| uATX form factor: 8.9 in. x 7.3 in. (22.6 cm x 18.5 cm)

Product introduction

Motherboard overview

• Unplug the power cord from the wall socket before touching any component.
• Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
• Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components.
• Unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage to motherboard components.

Scan the QR code to get the detailed pin definitions.

1. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)
   Correctly orient the ATX power supply plugs into these connectors and push down firmly until the connectors completely fit.

   •  For a fully configured system, we recommend that you use a power supply unit
     (PSU) that complies with ATX 12V Specification 2.0 (or later version) and provides a minimum power of 350 W. Ensure this PSU type has 24-pin and 4-pin power plugs.

   • We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices or when you intend to install additional devices. The system may become unstable or may not boot up if the power is inadequate.

   • DO NOT forget to connect the 4-pin ATX +12V power plug. Otherwise,the system will not boot up.

   • If you are uncertain about the minimum power supply requirement for your system, refer to the Recommended Power Supply Wattage Calculator at
     http://support.asus.com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en- us for  details.

2. CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN)
   Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector.
   Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! Do not place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan of maximum 0.5A (6 W) fan power.

3. Intel® LGA1151 CPU socket
   Install Intel® LGA1151 CPU into this surface mount LGA1151 socket, which is designed for 8th Generation Intel® Core™ i7 / i5 / i3, Pentium®, and Celeron® processors.
   For more details, refer to Central Processing Unit (CPU).

4. DDR4 DIMM slots
   Install 2 GB, 4 GB, 8 GB, and 16 GB unbuffered non-ECC DDR4 DIMMs into these DIMM sockets.
   For more details, refer to System memory.

5. Intel® H310 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~4)
   These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables.

6. Speaker connector (4-pin SPEAKER)
   The 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.

7. System panel connector (10-1 pin F_PANEL)
   This connector supports several chassis-mounted functions.

8. Clear RTC RAM (2-pin CLRTC)
   This header allows you to clear the CMOS RTC RAM data of the system setup information such as date, time, and system passwords.
   To erase the RTC RAM:

   • Turn OFF the computer and unplug the power cord.
   • Use a metal object such as a screwdriver to short the two pins.
   • Plug the power cord and turn ON the computer.
   •  Hold down the key during the boot process and enter BIOS setup to re-enter data.
     If the steps above do not help, remove the onboard battery and short the two pins again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.

9. USB 3.1 Gen 1 (up to 5Gb/s) connector (20-1 pin U31G1_12)
   Connect a USB 3.1 Gen 1 module to this connector for additional USB 3.1
   Gen 1 front or rear panel ports. This connector complies with USB 3.1 Gen 1 specifications and provides faster data transfer speeds of up to 5 Gbps, faster charging time for USB-chargeable devices, optimized power efficiency, and backward compatibility with USB 2.0.

10. USB 2.0 connectors (10-1 pin USB78, USB910)
    Connect a USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specifications and support up to 480Mbps connection speed.

11. Digital audio connector (4-1 pin SPDIF_OUT)
    Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis.

12. Serial port connector (10-1 pin COM)
    Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis.

13. TPM connector (14-1 pin TPM)
    This connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

14. Front panel audio connector (10-1 pin AAFP)
    This connector is for a chassis-mounted front panel audio I/O module that supports the HD audio standard. Connect one end of the front panel audio I/O module cable to this connector.

    • We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
    • If you want to connect a high-definition front panel audio module to this connector, set the Front Panel Type item in the BIOS setup to [HD Audio].

15. PCI Express 2.0 x1 slots
    This motherboard has two PCI Express 2.0 x1 slots that support PCI Express x1 network cards, SCSI cards, and other cards that comply with the PCI Express specifications.

16. PCI Express 3.0/2.0 x16 slot
    This motherboard supports a PCI Express 3.0/2.0 x16 graphic card that complies with the PCI Express specifications.

17. M.2 socket 3

This socket allows you to install M.2 (NGFF) SSD modules.

  * This M.2 socket supports M Key and 2242/2260/2280 storage devices.
  * When a device in SATA mode is installed on the M.2 socket, the SATA_2 port cannot be used.
  * Due to the Chipset limitation, when an M.2 device is installed in PCIe mode, the socket is set to PCIe 2.0.

Rear panel connectors

1. PS/2 Mouse port. This port connects to a PS/2 mouse.
2. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other VGA-compatible devices.
3. HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector, and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected content.
4. USB 3.1 Gen 1 (up to 5Gb/s) ports. These two 9-pin Universal Serial Bus (USB) ports are for USB 3.1 Gen 1 devices.
   • USB 3.1 Gen 1 devices can only be used for data storage.
   • We strongly recommend that you connect USB 3.1 Gen 1 devices to USB 3.1 Gen 1 ports for faster and better performance from your USB 3.1 Gen 1 devices.
   • Due to the design of the Intel® 300 series chipset, all USB devices connected to the USB 2.0 and USB 3.1 Gen 1 ports are controlled by the xHCI controller. Some legacy USB devices must update their firmware for better compatibility.

5.  LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN) through a network hub.
   LAN port LED indications
   Activity/Link LED Speed LED

   Status| Description| Status| Description
   Off| No link| OFF| 10Mbps connection
   Orange| Linked| ORANGE| 100Mbps connection
   Orange (Blinking)| Data activity| GREEN| 1Gbps connection
   Orange (Blinking then steady)| Ready to wake up from S5 mode|  |

6. Line In port (light blue). This port connects to the tape, CD, DVD player, or other audio sources.
7. Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, 5.1and 7.1-channel configurations, the function of this port becomes Front Speaker Out.
8. Microphone port (pink). This port connects to a microphone.
   Refer to the audio configuration table for the function of the audio ports in 2.1, 4.1, 5.1, or 7.1-channel configuration.
   Audio 2.1, 4.1, 5.1 or 7.1-channel configuration

Port

| Headset 2.1-channel| ****

4.1- channel

| ****

5.1- channel

| ****

7.1- channel

---|---|---|---|---
Light Blue (Rear panel)| Line In| Rear Speaker Out| Rear Speaker Out| Rear Speaker Out
Lime (Rear panel)| Line Out| Front Speaker Out| Front Speaker Out| Front Speaker Out
Pink (Rear panel)| Mic In| Mic In| Bass/Center| Bass/Center
Lime (Front panel)| –| –| –| Side Speaker Out

To configure a 7.1-channel audio output:
Use a chassis with HD audio module in the front panel to support a 7.1-channel audio output.

9. USB 2.0 ports. These 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1 devices.
10. PS/2 Keyboard port. This port connects to a PS/2 keyboard.

Central Processing Unit (CPU)

This motherboard comes with a surface mount LGA1151 socket designed for the 8th Generation Intel® Core™ i7 / Core™ i5 / Core™ i3, Pentium®, and Celeron® processors.
Unplug all power cables before installing the CPU.

• Ensure that you install the correct CPU designed for the LGA1151 socket only. DO NOT install a CPU designed for LGA1150, LGA1155 and LGA1156 sockets on the LGA1151 socket.

• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap
  is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.

• Keep the cap after installing the motherboard. ASUS will process Return Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA1151 socket.

• The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP cap.

Installing the CPU

Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary.

System memory

Overview
This motherboard comes with two Double Data Rate 4 (DDR4) Dual Inline Memory Module (DIMM) sockets. The figure illustrates the location of the DDR4 DIMM sockets:

Channel: Sockets

1. Channel A :  DIMM_A1*
2. Channel B : DIMM_B1*

• You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
• Always install DIMMs with the same CAS latency. For optimal compatibility, we recommend that you install memory modules of the same version or date code (D/C) from the same vendor. Check with the retailer to get the correct memory modules.
• DDR4 2666MHz and higher memory modules will run at max. 2666MHz on Intel® 8th Generation 6-core or higher processors.
• Memory modules with memory frequency higher than 2133 MHz and its corresponding timing or the loaded X.M.P. Profile is not the JEDEC memory standard. The stability and compatibility of these memory modules depend on the CPU’s capabilities and other installed devices.
• The default memory operation frequency is dependent on its Serial Presence Detect (SPD), which is the standard way of accessing information from a memory module. Under the default state, some memory modules for overclocking may operate at a lower frequency than the vendor-marked value.
• For system stability, use a more efficient memory cooling system to support a full memory load (2 DIMMs).
• Refer to www.asus.com for the latest Memory QVL (Qualified Vendors List).

Recommended memory configuration

Installing a DIMM

To remove a DIMM

M.2 Anchor Installation
The M.2 Anchor is a tool-less design to easily fasten and secure your M.2 SSD card to your motherboard without using extra tools.

To install the M.2 SSD card using the M.2 Anchor:

1. Locate the M.2 mounting hole on your motherboard and firmly insert the M.2 Anchor into the hole.

2. Insert the M.2 SSD card into the M.2 slot. The notch at the end of the M.2 SSD card shall align with the rod of the M.2 Anchor
   

3. Firmly insert the pin on the M.2 Anchor into the hole on itself.
   

To uninstall the M.2 SSD card:

1. Pull up the ring on the M.2 Anchor until it is separated from the hole.
2. Remove the M.2 SSD card from the M.2 slot.
   

BIOS information

• Scan the QR code to view the BIOS update guide.
• Before using the ASUS CrashFree BIOS 3 utility, rename the BIOS file in the removable device into PH310MER.CAP.

BIOS setup program
Use the BIOS Setup program to update the BIOS or configure its parameters. The BIOS screens include navigation keys and brief online help to guide you in using the BIOS Setup program.

Entering BIOS Setup at startup
To enter BIOS Setup at startup:
Press or during the Power-On Self Test (POST). If you do not press or , POST continues with its routines.

Entering BIOS Setup after POST
To enter BIOS Setup after POST:
Press ++ simultaneously.
Press the reset button on the system chassis.
Press the power button to turn the system off then back on. Do this option only if you failed to enter BIOS Setup using the first two options.
Using the power button, reset button, or the ++ keys to force reset from a running operating system can cause damage to your data or system. We recommend you always shut down the system properly from the operating system.

• The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.
• Visit the ASUS website at www.asus.com to download the latest BIOS file for this motherboard.
• If the system becomes unstable after changing any BIOS setting, load the default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu or press hotkey F5.
• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and reset the motherboard to the default value. See section Motherboard overview for information on how to erase the RTC RAM.

BIOS menu screen
The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode. Press to change between the two modes.

EZ Mode
By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode, fan profile and boot device priority. To access the Advanced Mode, click Advanced Mode(F7) or press .
The default screen for entering the BIOS setup program can be changed. Go to the Setup Mode item under the Boot menu.

The boot device options vary depending on the devices you installed to the system.

Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations.
To access the EZ Mode, click EzMode(F7) or press .

Search on FAQ
Move your mouse over this button to show a QR code. Scan this QR code with your mobile device to connect to the ASUS BIOS FAQ web page. You can also scan the QR code below.

Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items.

Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press , a confirmation window appears. Select OK to load the default values.

Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved. When you select this option or if you press , a confirmation window appears. Select OK to save changes and exit.

Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you select this option or if you press , a confirmation window appears. Select OK to discard changes and exit.

Launch EFI Shell from USB drives
This option allows you to attempt to launch the EFI Shell application (shellx64.efi) from one of the available USB devices.

Appendix

Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Compliance Statement of Innovation, Science and Economic Development Canada (ISED)
This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)
VCCI: Japan Compliance Statement
Class B ITE
KC: Korea Warning Statement

REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.

ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.

Regional notice for California
WARNING Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Google™ License Terms
Copyright© 2018 Google Inc. All Rights Reserved.
Licensed under the Apache License, Version 2.0 (the “License”); you may not use this file except in compliance with the License. You may obtain a copy of the License at:
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and limitations under the License.
ASUSTeK Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of related Directives. Full text of EU declaration of conformity is available at: www.asus.com/support

ASUS contact information

ASUSTeK COMPUTER INC.

• Address 4F, No. 150, Li-Te Road, Peitou, Taipei 112, Taiwan
• Telephone +886-2-2894-3447
• Fax +886-2-2890-7798
• Web site www.asus.com

Technical Support

• Telephone +86-21-38429911
• Fax +86-21-5866-8722, ext. 9101#
• Online support http://qr.asus.com/techserv

ASUS COMPUTER INTERNATIONAL (America)

• Address 48720 Kato Rd., Fremont, CA 94538, USA
• Telephone +1-510-739-3777
• Fax +1-510-608-4555
• Web site http://www.asus.com/us/

Technical Support

• Support fax +1-812-284-0883
• Telephone +1-812-282-2787
• Online support http://qr.asus.com/techserv

ASUS COMPUTER GmbH (Germany and Austria)

• Address Harkort Str. 21-23, 40880 Ratingen, Germany
• Fax +49-2102-959931
• Web site http://www.asus.com/de
• Online contact http://eu-rma.asus.com/sales

Technical Support

• Telephone +49-2102-5789555
• Support Fax +49-2102-959911
• Online support http://qr.asus.com/techserv

FCC COMPLIANCE INFORMATION

Per FCC Part 2 Section 2.1077

• Responsible Party: Asus Computer International
• Address: 48720 Kato Rd., Fremont, CA 94538
• Phone/Fax No: (510)739-3777/(510)608-4555

Hereby declares that the product

• Product Name : Motherboard
• Model Number : PRIME H310M-E R2.0

Compliance statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

References

• Global Take Back Service | Resource Regeneration | Circular Economy | ASUS ESG website, ASUS ESG goal
• Home - Identity Digital
• Apache License, Version 2.0
• ASUS Global
• ASUS Deutschland
• Official Support | ASUS Global
• ASUS USA
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>