SEALEY AP3020 2MTR Steel Workbench Instructions

: June 9, 2024
: SEALEY

Table of Contents

SAFETY
INTRODUCTION
SPECIFICATION
CONTENTS
ASSEMBLY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SEALEY AP3020 2MTR Steel Workbench Instructions

Refer to Instruction Manual

SAFETY

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.
Locate bench in a suitable working area.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use bench on level and solid ground, preferably concrete. Avoid tarmacadam since the bench may sink into the surface.
Keep the bench clean and tidy in accordance with good workshop practice.
Keep children and unauthorised persons away from the working area.
WARNING! This bench is not electrically insulated and is therefore not suitable for electrical repairs of any sort.
DO NOT use the bench for any purpose other than that for which it is designed.
DO NOT undertake work on the bench without the work piece being adequately secured. Use clamps or a vice (not included) to secure the work piece, both available from your Sealey dealer.
DO NOT use the bench out of doors.
DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.
DO NOT clean the bench with any solvents which may damage the paint surface.

INTRODUCTION

Manufactured throughout in 3mm steel plate for industrial durability and finished in red gloss to prevent corrosion. Sup[plied with single lockable drawer, which can be installed on the right or the left of the workbench. Includes bottom shelf for additional storage.

SPECIFICATION

Model no:……………………………………………………….. AP3020
Size (W x D x H ):……………………………..2000 x 650 x 865mm
Maximum capacity bench top (evenly distributed):……. 900kg

ASSEMBLY

The bench should be built upside down. Do not turn the right way up until all bolts have been fully tightened.
Lay one of the legs on the floor and place the shelf onto it as shown in fig.2.A . The shelf must be supported until both bolts are in place. The turned down lip at the front of the shelf should be nearest to the foot. Place a bolt into the hole nearest to the foot and hand tighten the nut down onto a washer. Continue to support the shelf. Turn it through 90 degrees so that you can bolt the same leg to the other side of the shelf. Only hand tighten at this stage.
Now attach a second leg to the shelf using two sets of fixings as shown fig. 2.B.
Put some protective material onto the floor and place the bench top face down on top of it. Refer to fig.3. Attach the remaining two legs to the back edge of the upturned bench using the nuts, bolts and washers provided, as shown in fig.3.A.
Lift the shelf with the legs attached and stand it on to the upturned bench top so that the legs go between the inner edge of the bench and the supports and the back edge of the shelf rests inside the legs already attached to the bench as shown in fig.3. Ensure that you have adequate help to do this.
Attach the back edge of the shelf to the rear legs using two sets of fixings on each leg. These fixings go in the holes furthest away from the feet. ( See fig.3.B.)
Now bolt the front legs to the cross members on the underside of the bench top. The legs should be on the outside faces of the cross members as indicated on fig.3.C. All fixings should be hand tight at this stage.
Check that the assembly is correct and then tighten all bolts with a 17mm spanner before the bench is turned upright.
Ensure that you have enough help to turn the bench upright and lift it into its final position. Support the bench whilst gently tipping it onto its rear face. Now roll the bench onto its four feet taking care not to let the feet slide asyou turn the bench fully upright.
To assemble the barrel lock to the draw ( see fig.1.A ), hook the locking arm through the draw front making sure that the lock is rotated so the flats on the barrel line up with the flats in the hole and the lock is the right way up so that the arm turns upwards into the locking position. Refer to fig.1. To fix the lock in place press firmly on the front of the lock until the two sprung teeth on the barrel pass through the hole and come to bear on the inside face of the draw.
Slide the draw unit fully into the sheet metal runners on the underside of the bench top ( see fig.1.B ) and lock the drawer. Take the bent sheet metal draw retaining plate ( see fig.1.C ) and screw it to the back of the draw in the orientation shown in the drawing. The draw retaining plate will then come to rest on the back of the bench front edge thus preventing the draw falling out when it is fully opened.

INSTALLATION

Note! Drawer may be fitted to either left or right-hand pair of runners.

INSTALLATION

Environmental Protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to arecycling centre and disposed of in a manner which is compatible with the environment. When the product becomescompletely unserviceable and requires disposal, drain off any fluids if applicable) into approved containers and dispose of the product and the fluids according to local regulations.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim

Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk.
IP32 7AR
www.sealey.co.uk
sales@sealey.co.uk