VisionTek Soundtube Pro V3 Waterproof Bluetooth Speaker User Manual
- June 9, 2024
- VisionTek
Table of Contents
VisionTek Soundtube Pro V3 Waterproof Bluetooth Speaker
VisionTek® SOUNDTUBE PROv3
WATERPROOF BLUETOOTH SPEAKER USER MANUAL
BASIC OPERATIONS
POWER BUTTON / MULTI – FUNCTION BUTTON
- Power On/Off- Long press the “O” button for 2-3sec
- Incoming Call- Short press “0” to answer double press “0” to refuse
- CalUHang Up -During a call, short press “0” to hang up
- Pause/Play Music- Short press “0” when playing music to Pause or Play
+ / – VOLUME BUTTONS
- Short press – to adjust the volume down, long press the – for the previous track
- Short press + to adjust the volume up, Long press+ for the next track
TWS (TRUE WIRELESS STEREO) BUTTON
- Short press “ ” to turn on/offTWS
- Long press “ ” for 2-3sec ta disconnect from Bluetooth
LED INSTRUCTIONS
| POWER ON | LED in dicatorflashes Blue |
|---|
BLUETDDTH MODE
| PLAY/PAUSE: LED indicator solid Blue
LED indicator flashing Blue, connected deviceout of range (10m/30ft).
If speaker is left in unconnected in pairing mode for over 10 minutes, thespeaker will turn off to preserve battery.
AUXIN MODE| LED indicator solid Green
CHARGING
STATUS
| LED in dicatorsolid Red
LED indicator turns off when fully charged
LOW BATTERY
INDICATOR
| LED indicator flashes Red
TWS| TWS indicator flashes White when pairing TWS indicator solid White when
paired
BLUETOOTH PAIRING
STEP 1 POWER ON
- Long press the “0” button for 2-3 seconds to power on the speaker. You will hear an alert tone. The speaker will enter Bluetooth pairing mode notated by the blue indicator LED blinking.
STEP 2 SELECT THE DEVICE
- Find “Soundtube Pro V3” in your Bluetooth device list on your mobile phone, tablet or PC.
STEP 3 PAIRING COMPLETE
- The LED indicator on the speaker will be a solid blue and you will hear a beep once the device is paired successfully. The device is now paired and you can start enjoying your SoundTube Pro V3.
TWS (TRUE WIRELESS STEREO) PAIRING
TWS PAIRING INSTRUCTIONS
Turn on two Pro V3 speakers and press the “Ce’ button on each speaker to begin
the TWS pairing sequence. You will hear an alert tone and the TWS indicator on
both speakers will fl.ash white. Once the automatic pairing is complete, you
will hear another alert tone and the TWS indicator on both speal<ers will be a
solid white. Once pairing has been completed, open the Bluetooth settings on
your device and select “SoundTube Pro V3” from the Bluetooth device list. This
will sync your device to the paired Bluetooth speakers. To disconnect a
speaker from the TWS link, simply press the “li:J” button on the speaker you
wish to disconnect. The TWS indicator of the speal<er that is no Longer paired
and connected to your device will turn off.
NOTE: For TWS pairing. you must first pair two speakers together prior to
connecting your smartphone or device.
PRODUCT SPECIFICATIONS
FREQUENTLY ASKED QUESTIONS
-
Q: What kind of charger should I use for the speaker?
A: All common USB to micro USB can be used, we recommend chargers above 5Vfl.8A. -
Q: What is the device priority of the speaker?
A: The speaker will prioritize AUX IN input followed by Bluetooth phone calls when paired, and finally Bluetooth music. -
Q: The speaker does not turn on.
A: Plug in the charger and try to turn on the speaker after a few minutes . -
Q: What if there is a crackling or distortion of sound when in use.
A: The speaker can be used at distances up to 10m with no environmental obstruction. If used at a distance greater than 10m or with an obstruction between the connected devices there may be distortion or loss of signal. -
Q: Why does the speaker shut down automatically when powered on
A: When there is no Bluetooth device paired or if the speaker is not connected in AUX mode within 10 minutes, the speaker will shut down to reduce power consumption. -
Q: The speaker cannot connect to a previously paired device.
A: On your device remove the speaker from the list of Bluetooth devices. On the speaker short press the Bluetooth Disconnect Button to restart pairing mode.
*This speaker supports mobile phones, tablets, PC, etc. Images and steps provided are based on a mobile phone experience.
1 YEAR WARRANTY
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received.
including the interference that may cause undesired operation.
This equipment has been tested and found to comply with the Limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy. And, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that which the receiver is connected.
- Consult the dealer or an experienced radionv technician for help.
Warning: Where shielded interface cables or accessories have been
provided with the product or specified additional components or accessories
elsewhere defined to be used with the installation of the product, they must
be used in order to ensure compliance with FCC. Changes or modification to
product not expressly approved by VisionTek Products. LLC could void your
right to use or operate your product by the FCC.
IC Statement: CAN ICES-003 (BJ/ NMB-003 (B)
This device complies with Industry Canada license-exempt RSS standard{s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Cordless {Radio Transiter) products: Section A.RSS-310 (27 MHz transmitters
and receivers): This Category II radio communication device complies with
Industry Canada Standard RSS-310. Section B.RSS-210 {2.4 GHz transmitters or
transceivers): This Category I radio communication device complies with
RSS-210 of Industry Canada.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>