EKIZNSN F073 20 Inch White Modern Indoor Ceiling Fan Owner’s Manual
- June 9, 2024
- EKIZNSN
Table of Contents
EKIZNSN F073 20 Inch White Modern Indoor Ceiling Fan Owner’s Manual
Safety Rules
Please read all safety instructions prior to installing your ceiling fan and save this document for future reference. If you are in doubt with any of the information provided or difficulty installing your fan, please the email customer service at: service_us@ekiznsn.com
- Before you begin installing the fan, shut power off the circuit breaker for the fuse box.
- Read all instructions and safety information before installing your new fan.
- All wiring must be in accordance with national and local electrical codes. ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
- Do not bend the blades while installing, balancing the blades, or cleaning the fan.
- Do not insert foreign objects in between rotating fan blades.
- Make sure the installation site you choose allows the fan blades to rotate without any obstructions.
- To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit before installing the light kit.
- After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.
- Turn the fan off and wait for the blades to stop completely before performing any maintenance or cleaning.
Plate Installation
Attach the mounting plate to the ceiling. There are two types of screws included in the pack.
The mounting plate is pre-assembled on the top of the fan. Loose the 4 side screws to disassemble it first.
-
For wooden ceiling
Drilling a pilot hole in your ceiling with the power drills first, then secure the plate with wood screws
-
For concrete ceiling
Drill a hole in the base material with a hammer drill and a correctly sized carbide drill bit for the anchor and clean out the hole of all debris. Knock expansion screw into the hole and then tighten it with a wrench
Wiring Preparation
-
Rotate the bottom cap to secure it to the blades, then secure the side bolt into the cap with a hexagon wrench in case of the blades falling or loosen
The mounting plate is pre-assembled on the top of the fan. Loose the 4 side screws to disassemble it first. -
Lift fan towards the ceiling to suspend from mounting bracket using security cable loop and washer hook. Then you can star t wiring without holding the fan body
Tips:
Seek the help of another person to hold the stepladder in place and to lift
the fan up to you once you are set on the ladder.
Wiring
WARNING
Disconnect the electrical supply circuit before wiring to reduce the risk of
electric shock.
- Put receiving unit into the top of the fan body and fastened it with electrical tape to avoid movement.
- Make wire connections according to wire colors, labels and diagram above.
Mount Fan to Bracket
Once wire connections are completed, lift fan body and carefully align collar with mounting bracket. Tabs on ceiling plate should seat into channel on inside of fan collar. Rotate fan so that set screw holes on fan body align with set screw holes on ceiling plate. Take care to not pinch or damage internal wires. Insert and firmly tighten two canopy screws from screw pack.
CAUTION
Align the marked L-shaped screw hole on the fan collar to tab stuck with the
red sticker on the mounting plate. Otherwise, the fan body will not fit the
plate.
Note: Do not tighten down set screws until all three are partly screwed in.
Remote Control
CAUTION
If the indicator light does’t bright while pressing any buttons, then check
the battery first. It may be reversed or out of power.
CAUTION
The remote is pre-paired with the fan. If the remote does not work,
please re-pair as follow:
Long press the “Pair Code” button within 5 seconds when the fan is powered on.
The light flashes, then the remote is connected with the fan successfully
APP Control
iPhone
android
APP available at iPhone’s APP Store & Google Play Store on Andorid.
Caution
If the QR-Code above is not valid, please scan the code below
APP Connection
Here is the APP Connection Guide on iPhone: (Connection for Android devices are similar)
-
Scan the QR-Code to download the APP and register an account as perthe instructions
-
Log in the account, and click “+” to add the device. You can edit the device name, room, and choose the device type(such like fan light)
-
Open the APP. If your Bluetooth is off, the notification will pop up. Go to Settings, then open the Bluetooth.
-
Power off the fan and then power it on again, and press the “Pair” button within 10 seconds. If the light flashes 3 times, the pairing is successful.
Maintenance
Here are some suggestions to help maintain your fan
- Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachment twice a year. Make sure they are secure.
- Clean your fan periodically to help maintain its new appearance over the year. Do not use water when cleaning. This could damage the motor, or possibly cause electrical shock.
- Use only a soft brush or lint-free cloth to avoid scratching the finish. Cleaning products may damage the finished
- There is no need to oil your fan. The motor has permanently lubricated bearings.
- If installed in a coastal, humid environment, regular surface cleaning may be necessary to avoid deterioration or oxidizing effects of salt or other corrosive elements. A Damp Location rating is not an assurance of finish durability. Preventative measures should be taken depending on the environmental exposures your fan will undergo to preserve and protect the finish quality and appearance of your fan.
WARNING
Before servicing or cleaning your fan, switch power off at the service panel
and lock the service disconnecting means to prevent power from being switched
on accidentally.
Troubleshooting
Please read all installation instructions carefully.
After reviewing the following tips, if you are unable to solve a problem,
please contact customer service for additional assistance
Fan makes humming noise
- Be sure you are using the control set supplied with your fan
- Make sure all fittings are firmly secured. Loose parts will often cause vibrational noise or humming. Removal and re-attachment can sometimes remedy such resonant vibrational noise.
Fan not repon ding to remote control
- Check that all wire connections are secure and made as instructed.
- Verify that power is on and reaching the receiver by a voltmeter.
- Verify that controller batteries are installed with proper polarity as indicated inside the battery cover
Fan woobles
- Make sure the mounting plate and hardware at the ceiling are secure and firmly fastened. If necessary, use the wood screws provided to further secure the outlet box to the joist.
- Carefully lower motor housing and verify that the mounting plate is secure to the outlet box, screws are tight.
Light does not work
- Check wire connections at ceiling and receiver.
- Confirm that LED wire leads and terminal block are properly connected to the LED board.
Fan makes repetitive ticking noise
- Check for obstructions in the rotor path.
- Make sure mounting hardware at the ceiling is secure.
- Make sure all other hardware and blade attachments are tight.
- Give fan adequate “Break in Period” of several hours to several days then repeat steps above.
Support
For Any Problems Contact Customer Service:
service_us@ekiznsn.com
Model: F073
Size: 20”
Weight: 9.58lbs
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>