Content TDPM 100 Horizontal Ribbon Mixer Instructions
- June 9, 2024
- Content
Table of Contents
Content TDPM 100 Horizontal Ribbon Mixer
General Introduction
The Horizontal Ribbon Mixer can be used to mix all kinds of powder products.
It consists of U-Shape tank, spiral and drive parts. The design is unique, and
the operation is quite simple. It is a new type of mixing equipment with the
characteristics of high efficiency, high uniformity, high crushing, low energy
consumption and low contamination. The blender with dual ribbon structure
design. Outer ribbon makes the material move from the sides to the center of
the tank and the inner ribbon push the product from the sides to the
convective mixing.
It is widely used in food, medicine, chemical, plastics, dyes and cosmetics
industries. Our mixers also featured with fast mixing, no mixing blind area,
stable running, convenient use, easy maintenance etc.
Working principle:
Specification
Model| TDPM 100| TDPM 200| TDPM 300| TDPM 500| TDPM 1000| TDPM 1500| TDPM
2000| TDPM 3000| TDPM 5000| TDPM 10000
---|---|---|---|---|---|---|---|---|---|---
Capacity
__
(L)
| __
100
| __
200
| __
300
| __
500
| __
1000
| __
1500
| __
2000
| __
3000
| __
5000
| __
10000
Volume
__
(L)
| __
140
| __
280
| __
420
| __
710
| __
1420
| __
1800
| __
2600
| __
3800
| __
7100
| __
14000
Loading rate| 40%-70%
Length
__
(mm)
| __
1050
| __
1370
| __
1550
| __
1773
| __
2394
| __
2715
| __
3080
| __
3744
| __
4000
| __
5515
Width
__
(mm)
| __
700
| __
834
| __
970
| __
1100
| __
1320
| __
1397
| __
1625
| __
1330
| __
1500
| __
1768
Height
__
(mm)
| __
1440
| __
1647
| __
1655
| __
1855
| __
2187
| __
2313
| __
2453
| __
2718
| __
1750
| __
2400
Weight
__
(kg)
| __
180
| __
250
| __
350
| __
500
| __
700
| __
1000
| __
1300
| __
1600
| __
2100
| __
2700
Total Power (KW)| __
3
| __
4
| __
5.5
| __
7.5
| __
11
| __
15
| __
18.5
| __
22
| __
45
| __
75
View of the whole machine
Note:
- mixer lid
- mixer U-shape hopper
- electric cabinet & control Panel
- pneumatic valve
- motor and gearbox
- castors
Preparation before operation
All the products have been tested and inspected strictly before the shipment. But the loose and wear of the components maybe caused in the process of transportation. Please check carefully for outer packing and surface of the machines when arrival to make sure that all parts are in place and the machine can work normally.
-
Fixing casters or footed glass. the machine should be put on a flatground.
-
Make sure that power supply and air supply is well matched as per request.
Note: Make sure the machine is well-grounded, there is ground wire in the electric cabinet, but since the casters are insulated, one ground wire is needed to connect with caster and fixed on ground. Note: The ground wire is fixed on the position marked with green circle. -
Making a thoroughly clean for the mixing tank before production.
-
Switching the power on.
-
Switching the main power switch to the ON position .
-
Rotating emergency stop switch clock wisely to open the power supply
-
Pressing the “ON” button to check whether the ribbon rotate normally and the direction is correct .
-
Connecting air supply.
-
Connecting air tube to 1 position. (In general, air pressure 0.6 pa is ok, pulling 2 position up to turn right or left to adjust air pressure if need)
-
Switching the discharge switch to on position, to check if the discharge valve work normally.
Operation & Setting
- Switching the power on.
- Switching the main power switch to the ON position .
- Rotating emergency stop switch clock wisely to open the power supply.
- Setting mixing time on the timer (that is the time of mixing. H: Hours M: Minutes S: Seconds)
- Pressing the “ON” button to start mixing, the mixing will stop automatically when the time is up.
- Switching the discharge switch to on position (during this process the mixing motor can be started to keep the materials easier to get out of the bottom).
- Switching the discharge switch to off position to close the pneumatic valve when mixing is completed.
- About the products with big density (more than 0.8g/cm3), we suggest feeding batch by batch after the mixer starts. it may burn down the motor if it starts after full loading.
Optional Functions
-
Spray system
It consists of pump, nozzles and hopper. a small amount of liquid can be mixed with powder materials with this system.
-
Double jacket cooling or heating function
The mixer also can be designed with the function to keep cold or heat. Add one layer outside the tank and put into medium into the interlayer to get the mixing material cold or heat. Usually use water for cool and hot steam of use electrical for heat.
Attentions
-
please close the discharge valve before mixing.
-
please cover the lid in order to prevent the product splashing during the mixing which may cause damage and accident.
-
The main shaft should be rotated in the regulated direction not in the reverse direction.
-
The current of the thermal protection relay should be matched with the motor rated current otherwise may cause damage to the motor.
-
If there are some abnormal noises occur during the mixing process like metal crack, friction; please stop the machine immediately to check the problem and fix them before starting again.
-
The mixing time can be set 1-15 minutes. Customers can set the mixing time as per request.
-
The lubricating oil (model: CKC 150) should be changed periodically. (please take away the black rubber)
-
Cleaning the machine regularly.
a) Please cover the motor, reducer and control box with plastic sheet and wash with water.
b) Drying the water droplets by air blowing. -
Changing packing gland periodically. (video will be sent to your email if you need)
TDPM100/200, powder supply: 380V,3P
TDPM100/200, powder supply: 220V,3P
Documents / Resources
|
Content TDPM 100 Horizontal Ribbon
Mixer
[pdf] Instructions
TDPM 100 Horizontal Ribbon Mixer, TDPM 100, Horizontal Ribbon Mixer, Ribbon
Mixer, Mixer
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>