NEU MASTER ‎N6013 Electric Brad Nailer Instruction Manual

NEU MASTER ‎N6013 Electric Brad Nailer

INTRODUCTION

• This tool is intended for stapling and nailing of cardboard, insulating material, fabrics, foils, leather, and similar materials on surfaces of wood or materials similar to wood
• Read and save this instruction manual

TECHNICAL SPECIFICATIONS

TOOL ELEMENTS

• A Lever for loading magazine
• B Slider
• C Magazine
• D Tacker head
• E Trigger
• F Impact control selection wheel
• G On/off switch

SAFETY

GENERAL SAFETY INSTRUCTIONS

WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

WORK AREA

• a) Keep the work area clean and well-lit. Cluttered and dark areas invite accidents.
• b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
• c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
• b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

PERSONAL SAFETY

• a) Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• b) Use safety equipment. Always wear eye protection. Safety equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
• c) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• d) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• e) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• f) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of these devices can reduce dust-related hazards.

POWER TOOL USE AND CARE

• a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• c) Ensure the switch is in the off position before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tools’ operation. If damaged, have the power tool repaired before use? Many accidents are caused by poorly maintained power tools.
• f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• g) Use the power tool, accessories and tool bits, etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

SERVICE

• a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR TACKERS

• Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand)

• Never push in the tacker head manually (there is a danger of injury when at the same time trigger is activated unintentionally)

• Never use the tool for fastening electrical wiring (contact with electrical wires can lead to fire and electric shock)

• Avoid damage that can be caused by screws, nails, and other elements in your workpiece; remove them before you start working

• Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tacker (tackers with a rating of 230V or 240V can also be connected to a 220V supply)

• In case of electrical or mechanical malfunction, immediately switch off the tool or unplug the charger from the power source

• We can assure the flawless functioning of the tool only when the original accessories are used

• This tool should not be used by people under the age of 16 years

• Do not expose the tool to rain.

USE

• Loading staples/nails
  

  • turn the tool upside down
  • press lever A while pulling slider B backward
  • insert the staple/nail strip into magazine C with the legs facing upward (maximal capacity 100 staples)
  • push slider B against tacker head D until it snaplocks
  • when inserting a nail strip (not supplied with the tool) tilt the tool in such a way, that the nail strip rests against the magazine side which corresponds with the nail symbol on the tacker head D
    

• Operating the tool
  

  • firmly press tacker head D against the workpiece until it is pushed in a few millimeters
  • briefly press switch E and then release again
  • switch F is locked as long as you do not press tacker head E against the workpiece, thus preventing accidental operation
  • At 20 shots/min, the tacker should be allowed to cool down after 30 minutes as it is only rated for short-time duty.
    !remove all staples/nails from the magazine after each use

• Impact control
  With wheel G the required impact level can be selected in steps

• • indicator F shows the selected impact level
    • “-” for thin and light materials such as foils and fabrics
    • “+” for thick and tough materials such as hardwoods and walls
    • before starting a job, find the optimal impact level by testing out spare material

APPLICATION ADVICE

• Fastening panels

• Do not use the tool for fastening ceiling paneling on profiled wood or grooves

• Fixing textiles!

• Avoid blank shots in order to reduce the wear of the impact strike

FAQs

What is the voltage of this tool?****

It is 110V.

What is the power of this tool?****

It is 0-3000pcs/min.

Is it suitable for wood and metal?****

Yes, it can be used on wood and metal.

What is the material of the magazine?****

The magazine is made of plastic.

Does this tool have a warranty?****

Yes, it has a one-year warranty.

What is the purpose of a brad nailer?****

A powered nail gun that fires 18-gauge brads is known as a brad nailer (small nails). Finish carpenters, in particular, utilize brad nails to build casing and base trim that is up to 3/8 inches thick.

How much air pressure is needed for a brad nailer?****

The required cubic feet per minute (CFM) and pressures (PSI) are specified for air-powered nailers. While 90 psi is a more practical target level, the minimum pressure is at least 70 psi.

What are the best uses for a brad nailer?****

Picture frames, paneling, and ornamental trim are among common applications for brad nails. They function nicely with birdhouses and other thin wood cutting. For thin trim work, such as that around windows or doors, shoe molding, and quarter-round molding, brads are fantastic.

Why is my electric brad nailer not sinking nails?****

The tool is probably not getting enough air if it is driving nails but they are not sinking all the way. Verify the fittings, hose, and compressor. Make sure your compressor is appropriate for the sort of tool you’re using and adjust your air pressure settings accordingly.

How many Gauge is a brad nailer?****

The majority of brad nails are produced from extremely thin 18-gauge wire. Finishing nails are substantially more durable than brad nails, often ranging from 16 to 10 gauge.

What size brad nailer is best?****

For a successful outcome, the brad’s length must be just correct. The fundamental rule is that a brad should be three times as long as the cloth it is fastening. For instance, the brad should be 45 mm long if the material is 15 mm thick. Choose a brad gun that can accommodate the brad length you want.

Download The PDF Link;NEU MASTER Electric Brad Nailer pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>