origo SF1621 14 Inch 3D Twister Stand Fan Instruction Manual

14″ 3D Twister Stand Fan
Instruction Manual

SF1621

• Read all instructions carefully before using the FAN, and keep this instruction for furture reference when necessary.
  ** This instruction manual can be acquired at www.origin.hk.

Important Safety Information

• Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may casue fire, electrical shock or injury to persons.
• Open the package and ensure that the Fan is undamaged. In case of doubt, do not use the FAN and contact your supplier.
• Do not let children play parts of package.
• Before using the Fan, check if the voltage marked on the rating label corresponds to themains at your home.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Avoid using extension cord as it may overheat and casue fire.
• Do not pull the power cord to disconnect from power source. Always grasp the plug to pull out.
• This Fan is intended for household use ONLY and not for industrial or outdoor use.
• Do not insert any objects into the Fan as it may cause an electric shock or damage. Do not block or tamper with the Fan in any manner while it is in operation.
• Do not leave the Fan unattended.Always unplug the Fan when not in use.
• WARNING: The On/Off switch should not be used as the sole means of disconnecting power. Always unplug the power cord before servicing or moving the unit.
• Always disconnected the Fan from the power supply when moving it from one location to another.
• **** This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact your local municipality for the nearest collection.
• The Fan is not intended for use in wet or damp locations. Never locate the Fan where it may fall into a bathtub or other water container.
• Do not place the Fan near a source of heat or fire.
• Keep the Fan clean to maintain in good condition (refer to maintenance section).
• Ensure that the Fan is switched off from the supply mains before removing the guard.
• WARNING: To avoid danger of electric shock, unplug from outlet when not in use and before cleaning. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard.

Main Parts

The picture is for reference only, everything in kind shall prevail.

Assembly

The picture is for reference only, everything in kind shall prevail.

1. Remove the blade cap and guard cap from the motor shaft.
2. Remove the rubber back under the rear guard, loose the screw, turn the front guard anti-clockwise and pull out the front guard, blade and rear guard.
3. Remove the fixing cap from the base of pole.
4. Connect the base with the pole, fasten it with the fixing cap.
5. Fixing the rear guard onto the front of motor housing by the guard cap.
6. Fixing the blade on the motor shaft by the blade cap.
7. Put the front guard onto the rear guard, turn the front guard clockwise.
8. Fix the rear guard with the screw, put the rubber back under the rear guard.

Function Setting

The Fan may be operated by the control panel or by your remote control.

1. Place the Fan on a stable and flat surface. Plug the Power Cord into an 220-240V~,50Hz electrical outlet.

2. POWER: Turn the Fan ON by pressing the” “key, the Fan start at speed 1.The picture is for reference only, everything in kind shall prevail.

3. SPEED: Press the speed increase key” +”to increase the desired speed (level 2…12).
   Press the speed decrease key” “to decrease the desired speed (level 11…1) The speed setting will be shown on the display.

4. OSC(UP/DOWN): Press the” “key to allow the Fan to UP/DOWN (U90/D12 )oscillate the wind direction. To stop the oscillation, press the key again.

5. OSC(LEFT/RIGHT): Press the”   “key to allow the Fan to LEFT/RIGHT oscillate the wind direction of 60° . To stop the oscillation, press the key again.

6. OSC ANGLE(LEFT/RIGHT): Press the” “key to set desired angle (30° /60° /120° ). The selected angle will be shown on the display.

7. MODE: Press the” “tkey to set the wind mode as Normal, Natural, Sleep or ECO (Al). The wind mode will be shown on the display.

8. SLEEP MODE : Fan speed will drop down one level every half hour from the original setting speed to the lowest speed as sleep mode.

9. ECO (Al) Mode: When the room temperature is below or equal to 19°C, the Fan will automatically off, “00” will be shown on display.
   Room Temp| Wind Speed
   ---|---
   19-20°C| Level 1
   20-21°C| Level 2
   21-22°C| Level 3
   22-23°C| Level 4
   23-24°C| Level 5
   24-25°C| Level 6
   25-26°C| Level 7
   26-27°C| Level 8
   27-28°C| Level 9
   28-29°C| Level 10
   29-32°C| Level 11

   32°C| Level 12

10. OFF TIMER: While the Fan is operating, press the “ ” key to set desired auto power off time, There are 16 time intervals, from 0.5-hour to 8-hour. The indicator will light on and the off time setting will be shown on the display.

11. PRESET START TIME: In Standby mode, press non “ON/OFF” key on the control panel or remote control, then press the ” ” to set desired preset start time. There are 16 time intervals, from 0.5-hour to 8-hour. The desired preset start time will be shown on the display and flashes. OCS(UP/DOWN & LEFT/RIGHT),  IND MODE, ECO MODE and SPEED can be set during the indicator flashes.

12. OFF: To turn off the Fan, press the ” ” key. *The Fan will automatically resume to its original positon after shutdown.

Remote Control

Dim: Press ” ” key on remote control to adjust brightness or turn off the back light of control panel.
Battery replacement: Use a pin to insert the hole of back case, press and slide the battery cover out. Then replace one 3V Lithium battery (CR2032).

1. Keep batteries out of reach of children. Should a child swallow a battery, consult a doctor immediately.
2. Do not recharge or dispose in fire.
3. Keep in a dry and cool place.
4. Insert battery in right direction.

Battery disposal – Please dispose the used battery per municipal or provincial law.

Maintenance

WARNING: ALWAYS UNPLUG THE POWER CORD BEFORE MOVING OR SERVICING. DO NOT IMMERSE THE FAN IN WATER! BEFORE CLEANING, MAKE SURE THAT THE UNIT HAS BEEN SWITCHED OFF AND IT IS UNPLUGGED FROM THE MAIN OUTLET.
Housing & Guard: Clean the outside of the Fan with a soft cloth, to remove presistent dirt or grime wipe down with a cloth that has been dampened with warm soapy water
Blade: Loose the screw and pull the front guard out. Clean the blade with a soft damp cloth, place back and fix the front guard with the screw after cleaning.
CAUTION: Do NOT use gasoline, benzene, thinner, harsh cleaners, etc., as they will damage the Fan. NEVER use ALCOHOL or any other SOLVENTS.
STORAGE: Store the Fan with these instructions in the original box in a cool and dry place.

Specifcation

Origin Map

OFFICE HOURS
10:30am – 12:30pm (Mon to Fri)
02:30pm – 05:30pm (Mon to Fri)
10:30am – 12:30pm (Saturday)
(Closed on Sunday and Holiday)

Warranty Card(1 year carry-in)

Item : 14″ 3D Twister Stand Fan
Model : SF1621
This product is warranted for 1 year (commercial use for 3 months) from the date of purchase under the following conditions:

1.  For any defect, in the judgment of our technician, if it is caused under normal use, we are responsible for repairing the product, and/or replacing parts at free of charge.

2. This warranty DOES NOT apply to:
   – If the product has been damaged through abuse, misuse, negligence or accidents;
   – Unauthorized repair, alteration/modification;
   – Any damage or scratch on the housing, front and rear guard, blade, remote or accessories.

3. The customer is requested to bring the unit to and from our Service Centre whenever service is needed.

4. Any defective parts, which had been replaced, shall be of our property.

5. This warranty is valid in H.K.S.A.R. only.

6. Please show the Invoice to get free service.
   ***Extra 3 months warranty: just complete Online Warranty Registration within 10 days from the date of receipt, free warranty will be extended to 15 months (not applicable to commercial use). Plaese enter our website: www.origo.hk

Service Centre
ORIGIN MARKETING LIMITED
Unit H, 21/F., Reason Group Tower (nearby 12 Wah Sing Street),
403 Castle Peak Road, Kwai Chung, N.T., Hong Kong.
Tel: 2156 8238www.origo.hkhttps://www.facebook.com /Origin-Marketing-Limited-327710507631440/

References

• ORIGIN

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>