LG OLED55G3PUA Series OLED Smart TV Owner’s Manual
- June 9, 2024
- LG
Table of Contents
OLED55G3PUA Series OLED Smart TV
ENGLISH _index
www.lg.com
Printed in Korea
Copyright © 2023 LG Electronics Inc. All Rights Reserved.
OWNER’S MANUAL
Safety and Reference
Please read this manual carefully before operating your set and retain it for
future reference.
OLED55G3PUA OLED65G3PUA OLED77G3PUA OLED83G3PUA
OLED77Z3PUA
The model and serial number of the product are located on the back and on one
side of the product. Record them below in case you ever need service.
Model Serial No.
MFL719463322301REV00
Supplier`s Declaration of Conformity
Trade Name LG
Responsible LG Electronics USA,
Party
Inc.
Address
111 Sylvan Avenue, North Building, Englewood Cliffs, NJ 07632
lg.environmental@ lge.com
LG Customer Information Center
For inquires or comments, visit www. lg.com or call;
1-800-243-0000 1-888-865-3026 1-888-542-2623
USA, Consumer User
USA, Commercial User
CANADA
Register your product Online! www.lg.com
Important Safety Instruction
· Read these instructions. · Keep these instructions. · Heed all warnings. ·
Follow all instructions. · Do not use this apparatus near water. · Clean only
with dry cloth. · Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions. · Do not install near any heat sources
such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat. · Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet. ·
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus. ·
Only use attachments/accessories specified by the manufacturer. · Use only
with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
· Unplug this apparatus during lightning storms or when unused for long
periods of time. · Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
By using this product, you agree that all disputes between you and LG arising
out of or relating in any way to this product (including but not limited to
warranty disputes) shall be resolved exclusively through binding arbitration
on an individual basis. The terms of the arbitration agreement (including
details on the procedure for resolving disputes) is available at
www.lg.com/us/arbitration (USA) or www.lg.com/ca_en/arbitration (Canada).
Before reading this manual
· Read this manual thoroughly before operating your TV, and keep it for future
reference. · On the website you can download the manual including
installation, using, troubleshooting, specifications, license etc and view its
contents on your PC or
mobile device. · User Guide: For more information about this TV, read the USER
GUIDE embedded in the product. (Depending upon model)
– To open the USER GUIDE [ ] [Support] [User Guide] Optional Extras
· Optional extras can be changed or modified for quality improvement without
any notification. Contact your dealer for buying these items. These devices
work only with certain models. The model name or design may be changed due to
the manufacturer’s circumstances or policies.
· A cable to connect antennas and external devices must be purchased
separately.
Note · Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions. · The items supplied
with your product may vary depending upon the model. · Image shown may differ
from your TV.
2
Warning! Safety instructions
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons. The symbol is
intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the
device. WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
· TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH OPEN FLAMES
AWAY FROM THIS PRODUCT AT ALL TIMES.
· Do not place the TV and/or remote control in the following environments: –
Keep the product away from direct sunlight. – An area with high humidity such
as a bathroom. – Near any heat source such as stoves and other devices that
produce heat. – Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil. – An area exposed to rain or wind. – Do not expose to
dripping or splashing and do not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).
– Near flammable objects such as gasoline or candles, or expose the TV to
direct air conditioning. – Do not install in excessively dusty places.
Otherwise, this may result in fire, electric shock, combustion/explosion,
malfunction or product deformation. · Ventilation – Install your TV where
there is proper ventilation. Do not install in a
confined space such as a bookcase. – Do not install the product on a carpet or
cushion. – Do not block or cover the product with cloth or other materials
while
unit is plugged in. · Take care not to touch the ventilation openings. When
watching the TV
for a long period, the ventilation openings may become hot. · Protect the
power cord from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the
device. · Do not move the TV whilst the Power cord is plugged in. · Do not use
a damaged or loosely fitting power cord.
· Be sure to grasp the plug when unplugging the power cord. Do not pull on the
power cord to unplug the TV.
· Do not connect too many devices to the same AC power outlet as this could
result in fire or electric shock.
· Disconnecting the Device from the Main Power – The power plug is the
disconnecting device. In case of an emergency, the power plug must remain
readily accessible.
· Do not let your children climb or cling onto the TV. Otherwise, the TV may
fall over, which may cause serious injury.
· Outdoor Antenna Grounding (Can differ by country): – If an outdoor antenna
is installed, follow the precautions below. An outdoor antenna system should
not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can come in contact with such power lines or
circuits as death or serious injury can occur.
Be sure the antenna system is grounded to provide some protection against
voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A. provides
information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit, connection to
grounding electrodes and requirements for the grounding electrode.
Antenna grounding according to the National Electrical Code, ANSI/ NFPA 70 ·
Never touch this apparatus or antenna during a lightning storm. You may be
electrocuted. · Make sure the power cord is connected securely to the TV and
wall socket if not secured damage to the Plug and socket may occur and in
extreme cases a fire may break out. · Do not insert metallic or inflammable
objects into the product. If a foreign object is dropped into the product,
unplug the power cord and contact the customer service. · Do not touch the end
of the power cord while it is plugged in. You may be electrocuted.
3
· If any of the following occur, unplug the product immediately and contact
your local customer service. – The product has been damaged. – If water or
another substance enters the product (like an AC adapter, power cord, or TV).
– If you smell smoke or other odors coming from the TV – When lightning storms
or when unused for long periods of time.
Even the TV is turned off by remote control or button, AC power source is
connected to the unit if not unplugged in. · Do not use high voltage
electrical equipment near the TV (e.g., a bug zapper). This may result in
product malfunction. · Do not attempt to modify this product in any way
without written authorization from LG Electronics. Accidental fire or electric
shock can occur. Contact your local customer service for service or repair.
Unauthorized modification could void the user’s authority to operate this
product. · Use only an authorized attachments / accessories approved by LG
Electronics. Otherwise, this may result in fire, electric shock, malfunction,
or product damage. · Never disassemble the AC adapter or power cord. This may
result in fire or electric shock. · Handle the adapter carefully to avoid
dropping or striking it. An impact could damage the adapter. · To reduce the
risk of fire or electrical shock, do not touch the TV with wet hands. If the
power cord prongs are wet or covered with dust, dry the power plug completely
or wipe dust off.
· Batteries – Store the accessories (battery, etc.) in a safe location out of
the reach of children. – Do not short circuit, disassemble, or allow the
batteries to overheat. Do not dispose of batteries in a fire. Batteries should
not be exposed to excessive heat. – Caution: Risk of fire or explosion if the
battery is replaced by an incorrect type.
· Moving – When moving, make sure the product is turned off, unplugged, and
all cables have been removed. It may take 2 or more people to carry larger
TVs. Do not press or put stress on the front panel of the TV. Otherwise, this
may result in product damage, fire hazard or injury.
· Keep the packing anti-moisture material or vinyl packing out of the reach of
children.
· Do not allow an impact shock, any objects to fall into the product, and do
not drop anything onto the screen.
· Do not press strongly upon the panel with a hand or a sharp object such as a
nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.
· Cleaning – When cleaning, unplug the power cord and wipe gently with a soft/
dry cloth. Do not spray water or other liquids directly on the TV. Do not
clean your TV with chemicals including glass cleaner, any type of air
freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner,
benzene, alcohol etc., which can damage the product and/ or its panel.
Otherwise, this may result in electric shock or product damage.
Installation
Lifting and moving the TV
When moving or lifting the TV, read the following to prevent the TV from being
scratched or damaged and for safe transportation regardless of its type and
size.
· It is recommended to move the TV in the box or packing material that the TV
originally came in.
· Before moving or lifting the TV, disconnect the power cord and all cables. ·
When holding the TV, the screen should face away from you to avoid
damage. · Hold the side and bottom of the TV frame firmly. Make sure not to
hold
the transparent part, speaker, or speaker grille area. · Use at least two
people to move a large TV. · When transporting the TV, do not expose the TV to
jolts or excessive
vibration. · When transporting the TV, keep the TV upright; never turn the TV
on its
side or tilt towards the left or right. · When handling the TV, be careful not
to damage the protruding buttons.
· Avoid touching the screen at all times, as this may result in damage to the
screen.
· Do not place the product on the floor with its front facing down without
padding. Failure to do so may result in damage to the screen.
· When attaching the stand to the TV set, place the screen facing down on a
cushioned table or flat surface to protect the screen from scratches.
Mounting on the Table
1 Lift and tilt the TV into its upright position on a table. · Leave a minimum
of 10 cm (4 inches) space from the wall for proper ventilation, (Depending
upon model).
2 Connect the power cord to a wall outlet.
4
· Do not apply foreign substances (oils, lubricants, etc.) to the screw parts
when assembling the product. (Doing so may damage the product.)
· Do not use any unapproved items to ensure the safety and lifespan of the
product.
· Any damages or injuries by using unapproved items are not covered by the
warranty.
· If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which may
cause injury.
· When assembling the stand, ensure that all of the provided screws are
attached. If the screws are not fully tightened, the product may tilt or tip
over, resulting in damage. Tightening the screws with excessive force may
cause them to come off due to abrasion of the screw joint.
· When installing on a cabinet or a shelf using a stand, make sure its width
is greater than that of the TV, (Depending upon model).
· If the TV is placed on the stand, its screen may be tilted back slightly. If
the stand is not level because an object is placed under the stand or it is
not on a flat surface, the product may fall and cause injury or product
damage, (Depending upon model).
Securing TV to the Wall
1 Insert and tighten the eye-bolts or TV brackets and bolts on the back of the
TV. · If there are bolts inserted at the eye-bolts position, remove the bolts
first.
2 Mount the wall brackets with the bolts to the wall. Match the location of
the wall bracket and the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope or cable.
Make sure to keep the rope parallel to the flat surface.
· Use a platform or cabinet that is strong and large enough to support the TV
securely.
· Brackets, bolts, and ropes are optional. You can obtain additional
accessories from your local dealer.
Stand (Optional Extras)
(Depending upon model) Stand
SR-G3WU55 SR-G3WU65 SR-G3WU8377
Model OLED55G3 OLED65G3 OLED77/83G3*
Mounting to the Wall
An optional wall mount can be used with your LG Television. Consult with your
local dealer for a wall mount that supports the VESA standard used by your TV
model. Carefully attach the wall mount bracket at the rear of the TV. Install
the wall mount bracket on a solid wall perpendicular to the floor. If you are
attaching the TV to other building materials, please contact qualified
personnel to install the wall mount. Detailed instructions will be included
with the wall mount. We recommend that you use an LG brand wall mount. The LG
wall mount is easy to adjust or to connect the cables. When you do not use
LG’s wall mount bracket, use a wall mount bracket where the device is
adequately secured to the wall with enough space to allow connectivity to
external devices. If you are using a non-adjustable mount, attach the mount to
the wall. Attach the cables to the TV first, then attach the TV to the mount.
· Remove the stand before installing the TV on a wall mount by performing the
stand attachment in reverse.
· For more information of screws and wall mount bracket, refer to the Separate
purchase.
· If you intend to mount the product to a wall, attach VESA standard mounting
interface (optional parts) to the back of the product. When you install the
set to use the wall mounting bracket (optional parts), fix it carefully so as
not to drop.
· When mounting a TV on the wall, make sure not to install the TV by hanging
the power and signal cables on the back of the TV.
· Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
· When installing the Full Contact Wall Mount, the TV may not be contacted
firmly against the wall due to some wall conditions.
Precautions for Safety
(Except for OLW480B, LSW440B) · Professional installers should read this
manual carefully to ensure proper installation. · Professional installers
should forward this manual to customers after installation and encourage them
to read and store it in a convenient place for future reference. After reading
the installation manual, keep it in a convenient place for future reference.
· Ask a professional installer appointed by the store for installation of the
product. Installation by someone other than a professional installer is
extremely dangerous and may result in personal injury.
· Do not install the product in an unstable site that cannot withstand its
weight. If the installation site lacks sufficient rigidity, the product may
fall and cause personal injury.
· Contact a professional installer appointed by the store prior to moving or
replacing the product after installation. Installation is a technical task and
safety issues may arise if an individual attempts to install or move the
product personally.
5
· Do not hang on the product or subject it to severe impact after
installation.
Doing so may cause the product to fall and cause personal injury. · When
installing the product on a wall, do not hang the power line or
signal cables from the back of the TV.
This can damage the cords, resulting in a fire, electrical shock or
malfunction of the product. · Be sure to wear work gloves when installing the
product. – Installing with unprotected hands may result in injury. · Install
the product according to the instructions in the installation manual.
Failure to install the product according to the instructions in the
installation manual can result in serious personal injury or product damage. ·
Be sure to have at least two people when installing the product or adjusting
the product’s height.
Attempting to perform installation or adjustments personally may result in
personal injury or damage to the product. · Make sure a wall is available
prior to proceeding with installation. Make use of the anchors and screws
provided with the product.
Use of any unauthorized anchors or screws may not support the product’s
weight, which poses safety risks. · When drilling in the wall for
installation, be sure to use drill bits and drills of the specified diameter.
Follow the instructions for the hole depth.
Drilling and installing the product in ways other than specified in the
installation manual may result in an unstable installation and potential
safety issues. · Do not wipe the product with a wet towel or use any heating
equipment or humidifier under the place where the product is installed.
Liquid water or vapor may enter the product and excessive heat may cause fire,
electric shock, or malfunction. · Do not install the product near a fire
sprinkler or detector, a place where vibration or shock may occur or near a
high-voltage wire or power source. · Unplug the product’s power cord from the
wall outlet before installing.
Installing the product while the power cord is plugged in may result in
electric shock or fire. · Do not install the product with bare hands. Be sure
to wear work gloves.
Attempting installation without work gloves may cause personal injury. ·
Connect the product with the supplied cable. Use of an unauthorized
cable may result in damage by friction with the wall. Make sure to use the
supplied cable gender. (This may vary by model.)
Before Installation
(Except for OLW480B, LSW440B) · Do not use the product for any purpose other
than installing the TV on a wall. · Avoid product damage and safety accidents
caused by careless installing or use of improper or unauthorized wall mount. ·
Follow the instructions in the installation manual for a convenient
installation of the wall mount. · Immediately discontinue installation and
contact the service center if you cannot fully understand the installation
process.
Use a professional installer if any installation issues remain after the
inquiry. · Installation of this product on a concrete wall or wood stud is
recommended. Installation of this product on other surfaces (Dry wall,
plywood, bricks, etc.) is not recommended. Improper installation may result in
the product falling. · Install the product only on a vertical wall. Do not
install on a tilted wall that exceeds building standards or on the heavily
titled wall or ceiling.
LG is not responsible for problems caused by improper installation of the
product, e.g., heavily tilted walls and ceilings. · Check the enclosed
accessories before installation. We are not responsible for any lost or
damaged accessories after the inner packaging is opened. · When an infant or
small child swallows the enclosed accessories, various safety accidents such
as choking may occur. Keep the enclosed accessories out of the reach of
infants and children. · When tightening screws, tighten until fully snug.
Avoid using excessive force when tightening the screws. Doing so may damage
the wall and product or reduce the rigidity or performance of the product. ·
Avoid installing a TV that exceeds the specified tensile load, and do not
allow any external force to be applied to the product. · Avoid accidents by
using work tools with care during installation.
Tools for Installation · “+”shaped screwdriver (manual or electric) / level /
drill / Ø 8 mm drill bit for concrete or Ø 4 mm drill bit for steel
Securing TV to the Wall
(Except for OLW480B, LSW440B)
· Please use the TV close to the wall after installation. 6
How to fix anchors and screws
(Except for OLW480B, LSW440B)
Please make sure that:
· Check that the material and thickness of the wall and finishing material
comply with the installation manual. Before beginning the mounting process,
you must be sure the wall is able to support the weight of the TV.
· Should use the enclosed anchors and screws on crack-free concrete walls. ·
Never install the product on a plasterboard or wall made of paper or
medium-density fiberboard (MDF). When it is necessary to install the product
on such wall, anchor screws must be fastened to retaining walls (concrete) or
wood Stud inside the finishing material. · The wall mount should be attached
to a stud. This usually will not be a problem, but depending upon individual
circumstances, there may be cases when the ability to mount into a stud is not
possible. In this case, there are a variety of drywall anchors, such as toggle
bolts, which may provide a solution. If using drywall anchors, please be sure
the anchors and the wall have the ability to support the weight of your TV.
Please note that the supplied anchors may not be the correct ones for your
individual situation, so you should check with a local professional. · Other
unspecified walls must be capable of supporting pullout loads of over 70 kgf
(154 lbf) (686 N) and shear loads of over 100 kgf (220 lbf) (980 N) per
fastener. · Use an Ø 8 mm drill bit for concrete and a hammer (impact) drill
or Ø 4 mm drill bit for wood stud to drill holes.
For installation on wood stud
Drywall
76 mm (2.9 inches)
Wood stud Use the Ø 4 mm drill bit for wood to drill holes with the depth of
76 mm (2.9 Inches). (Clean the drilled hole.) Without using the wall mounting
anchor, fasten the wall mounting screw directly to the wood stud.
After Installation
· When connecting additional cables from the sides, we recommend holding the
center of the TV horizontally or vertically and pulling the product to make
sure there is sufficient distance from the wall before connecting.
· When connecting additional cables from the bottom, we recommend releasing
the TV from the wall mount before connecting.
For installation on concrete wall
Wall mounting anchor
Wall mounting screw
1 Drill holes in anchor locations with a drill bit of Ø 8 mm to a depth of 80
mm (3.14 inches) to 100 mm (3.93 inches).
2 Clean the drilled holes. 3 Insert the enclosed anchors for fixing the wall
mount into the holes. (Use
a hammer when inserting anchors.) 4 Push the wall mount support closely toward
the wall to match the hole
locations. 5 Tighten screws for fixing the wall mount to the holes. At this
time, tighten
the screws to a torque of between 45 kgf/cm (39.06 lbf/in) to 60 kgf/cm (52.07
lbf/in).
(For example)
· Use cable management systems to arrange the cables at the bottom of the TV
as shown below. Cable managements are not provided with the product, so
purchase them separately.
· After installing the product, be sure to use it adhered to the wall. – Using
the product while it is not adhered to the wall may damage or shake the
product.
7
Antenna/Cable
Connect an antenna, cable, or cable box to watch TV while referring to the
following. The illustrations may differ from the actual items and an RF cable
is optional.
Copper wire
· Make sure not to bend the copper wire of the RF cable. · Complete all
connections between devices, and then connect the power
cord to the power outlet to prevent damage to your TV. · Use a signal splitter
to use 2 TVs or more. · DTV Audio Supported Codec: MPEG, Dolby Digital · This
TV cannot receive Ultra HD (3840 x 2160 pixels) broadcasts directly
because the related standards have not been confirmed (Depending
upon country).
Starting TV
Turning on the TV
You can simply operate the TV functions, using the button.
Power On (Press) Power Off1) (Press and Hold) Menu Control (Press2)) Menu Selection (Press and Hold3))
- All running apps will close. 2) You can access and adjust the menu by
pressing the button when TV is on. 3) You can use the function when you access
menu control.
Note · When the TV is turned on for the first time after being shipped from the
factory, initialization of the TV may take approximately one minute. · Your TV’s OSD (On Screen Display) may differ slightly from that shown
in this manual. · The device must be easily accessed to a location outlet near the access.
Some devices are not made by turning on / off button, turning off the device and unplugging the power cord.
8
Connections
You can connect various external devices to the TV. For more information on external device’s connection, refer to the manual provided with each device.
HDMI
· When connecting the HDMI cable, the product and external devices should be
turned off and unplugged.
· Supported HDMI Audio format (Depending upon model):
True HD (48 kHz),
Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz),
PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)
DTS (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)
DTS-HD (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz / 192 kHz)
Note · If the device connected to Input Port also supports HDMI Deep Color,
your picture may be clearer. However, if the device doesn’t support it, it may
not work properly. In that case, change the TV’s [HDMI Deep Color] setting to
off. · [ ] [General] [External Devices] [HDMI Settings] [HDMI Deep Color] ·
Use a certified cable with the HDMI logo attached. If you do not use a
certified HDMI cable, the screen may not display or a connection error may
occur. · Recommended HDMI cable types – Ultra High Speed HDMI®/TM cable (3 m
(9.84 feet) or less)
USB
Some USB Hubs may not work. If a USB device connected through a USB Hub is not
detected, connect it directly to the USB port on the TV.
Note
· For an optimal connection, HDMI cables and USB devices should have
bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches)
width. (Depending upon model)
· Use an extension cable that supports
if the USB cable or USB
flash drive does not fit into your TV’s USB port.
External Devices
Supported external devices are: Blu-ray player, HD receivers, DVD players,
VCRs, audio systems, USB storage devices, PC, gaming devices, and other
external devices.
Note · The external device connections shown may differ slightly from
illustrations in a manual. · In PC mode, there may be noise associated with
the resolution, vertical
pattern, contrast or brightness. If noise is present, change the PC output to
another resolution, change the refresh rate to another rate or adjust the
brightness and contrast on the [Picture] menu until the picture is clear.
Depending upon the graphics card, some resolution settings may not allow the
image to be positioned on the screen properly. · When connecting to a wired
LAN, use a CAT 7 cable with high-speed Internet transmission. (Only when port
is provided.) · The TV may be capable of operating without a set-top-box from
a multichannel video programming distributor (MVPD).
Remote RS-232C setup
To obtain the RS-232C external control setup information, please visit www.
lg.com. Download and read the manual, (Depending upon model).
· Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
· When connecting external devices such as video game consoles, make sure the
connecting cables are long enough. Otherwise, the product may fall over, which
may cause injury or damage the product.
IR Blaster
Control the set-top box (cable/satellite/IP/OTT), Blu-ray/DVD player,
soundbar, game consoles, etc., using the IR Blaster. (Depending upon country)
· Connect the IR Blaster cable to the TV’s IR Blaster port. · Use universal
control settings to control the device. · Secure the IR Blaster with the 3M
tape provided. · In order to control external devices through “Room to Room
Share” and
“Hands-free Voice Control”, an IR blaster connection is required.
9
Specifications
Power requirement
AC 120 V~ 50/60 Hz
Product specifications may be changed without prior notice due to upgrade of
product functions.
Estimated yearly energy consumption indicated on the FTC label is measured in
accordance with the Test Procedures for Television Sets (USA only).
The actual energy consumption depends on the usage environment (The content
watched, TV settings, etc.). · For information of the power supply and power
consumption, refer to the label attached to the product. – The typical power
consumption is measured in accordance with IEC 62087 or each country’s energy
regulations. On some models, the label is inside the external device
connection terminal cover. Depending upon the model or country, the typical
power consumption may not be on label.
(Depending upon country)
Television system Channel coverage
(Band) External antenna impedance
Broadcasting Specifications ATSC, ATSC3.0 (Only USA), NTSC-M, 64 & 256 QAM
VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135 75
· Certain 8K input/decoding standards may not be supported. An additional device may be necessary to support certain 8K standards. Upscaled and enhanced 8K images will vary depending upon the source content (Depending upon model).
Operating Temperature Operating Humidity
Environment Condition
0 °C to 40 °C (32 °F to 104 °F)
Storage Temperature
Less than 80 %
Storage Humidity
Conditions for Wall Mount Installation Tilt Angle * This specification range applies to TV wall mounts when adjusting for proper viewing angle.
0° – 15°
-20 °C to 60 °C (-4 °F to 140 °F) Less than 85 %
10
Product Information
Wireless module(LGSBWAX12)Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac/ax)
Frequency range
Output Power (Max.)
2,400 to 2,472 MHz
17 dBm
5,150 to 5,725 MHz
15 dBm
5,725 to 5,850 MHz
15 dBm
5,945 to 7,125 MHz
11 dBm
Bluetooth
Frequency range
Output Power (Max.)
2,400 to 2,483.5 MHz
9 dBm
As band channels can vary per country, the user cannot change or adjust the
operating frequency. This product is configured for the regional frequency
table. For consideration of the user, this device should be installed and
operated with a minimum distance of 20 cm (7.8 inches) between the device and
the body. 1) FCC regulations restrict the operation of this device to indoor
use only. 2) Operation prohibited on oil platforms, cars, trains, boats, and
aircraft,
except that operation of this device is permitted in large aircraft while
flying above 10,000 feet.
FCC ID: BEJLGSBWAX12 / IC: 2703H-LGSBWAX12
Open Source Software Notice Information
To obtain the source code that is contained in this product, under GPL, LGPL,
MPL, and other open source licenses that have the obligation to disclose
source code, and to access all referred license terms, copyright notices and
other relevant documents please visit https://opensource.lge.com. LG
Electronics will also provide open source code to you on CD-ROM for a charge
covering the cost of performing such distribution (such as the cost of media,
shipping, and handling) upon email request to opensource@lge.com. This offer
is valid to anyone in receipt of this information for a period of three years
after our last shipment of this product.
Licenses
(Magic Remote supported models only)
11
Troubleshooting
In TV / HDMI input, press the button on the remote control three times to display the model name and serial number on the screen.
Cannot control the TV with the remote control. No image display and no sound
is produced. The TV turns off suddenly.
Abnormal Display
Generated Sound
The TV does not turn on continuously due to Always Ready mode operation or
does not automatically turn on by sensor.
· Check if anything such as tape has been placed over the receiver. · Check if
there is any obstacle between the product and the remote control. · Replace
the batteries with new fresh ones.
· Check if the product is turned on. · Check if the power cord is connected to
a wall outlet. · Check if there is a problem in the wall outlet by connecting
other products.
· Check the power control settings. The power supply may be interrupted. ·
Check if the auto-off function is activated in the settings menu. · The auto-
off function may have worked. This product is equipped with an auto-off
function that automatically
turns off the power if the remote control is not used for 15 minutes without
an input signal.
· If the product feels cold to the touch, there may be a small”flicker”when it
is turned on. This is normal, there is nothing wrong with product.
· This panel is an advanced product that contains millions of pixels. You may
see tiny black dots and/or brightly colored dots (white, red, blue or green)
at a size of 1 ppm on the panel. This does not indicate a malfunction and does
not affect the performance and reliability of the product. This phenomenon
also occurs in third-party products and is not subject to exchange or refund.
· You may find different brightness and color of the panel depending upon your
viewing position(left/right/ top/down). This phenomenon occurs due to the
characteristic of the panel. It is not related with the product performance,
and it is not malfunction.
· Avoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary distortion effects on the
screen.
· Cracking noise A cracking noise that occurs when watching or turning off the
TV is generated by plastic thermal contraction due to temperature and
humidity. This noise is common for products where thermal deformation is
required.
· Electrical circuit humming/panel buzzing A low level noise is generated from
a high-speed switching circuit, which supplies a large amount of current to
operate a product. It varies depending upon the product. This generated sound
does not affect the performance and reliability of the product.
· The motion sensor is located on the bottom center of the TV. · The motion
sensor is only supported by some models. · If there is a foreign substance on
the motion sensor, it may not work properly. · If the environment around the
TV is too bright or too dark, the motion sensor may not work properly. ·
Obstacles in front of the TV may affect the detection function of the motion
sensor. · It can operate by recognizing changes in lighting around the TV or
movement of objects (pets/robot vacuum
cleaners, etc.). · To stop using the Always Ready mode in [ ] [General]
[Always Ready] [Enable the function],
or to use only the General Always Ready mode function, you can select Enable
Always Ready mode, turn off the screen, and then stop using the motion sensor
in [Always Ready Settings]. The screen-on function with the motion sensor can
be set by adjusting the performance of the sensor through the [Always Ready
Settings] [Motion Sensor Sensitivity] setting.
· Make sure to wring any excess water or cleaner from the cloth. · Do not spray water or cleaner directly onto the TV screen. · Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.
12
Precautions for Protecting the OLED TV Screen
Unlike regular LED/LCDs, OLED TVs produce images that emit light for each
pixel, achieving a perfect black color and delivering clear images without
blurring. Due to the nature of the organic materials used to achieve high-
resolution image quality, OLED displays generally experience image retention
on the screen, which can be a persistent phenomenon. This phenomenon is
observed in all OLED panels, and although recommended picture modes can
minimize image retention, current technology cannot completely prevent this
from occurring. Displaying the same image for a long time or repeatedly
displaying the same image can cause image retention on the screen, which is a
common phenomenon in OLED panel products due to the nature of the product.
This product has a built-in screen protection feature. Avoid displaying images
that are likely to cause image retention, and follow the recommendations.
Images that are likely to cause image retention
· Images with black areas on the top and bottom and/or the left and right
sides of the screen.
· Images whose aspect ratio is 4:3 or 21:9. · Images that are fixed for a long
time, such as channel number, station
logo, game console icon, set-top box menu, etc. · Other fixed screen images or
repeatedly displayed images.
Recommendations for Minimizing Image Retention
When watching the TV for a long time, press the button on the remote control,
go to [ ] [Picture] [Select Mode] and set the mode to [Auto Power Save], go to
[Advanced Settings] [Brightness] and set [OLED Pixel Brightness] to a lower
level. In addition, press the button on the remote control, go to [ ]
[General] [OLED Care] [OLED Panel Care] and set the [Adjust Logo Brightness]
value to [High].
When showing images with black bars at the top/bottom/left/right side of the
screen, press the button on the remote control, press [ ], and go to [Picture]
[Aspect Ratio] [User Selection] [Vertical Zoom] or [4-Way Zoom] to remove the
black bars.
Turn off the menus for setting up devices such as set-top boxes so that they
are not displayed on the screen for a long time.
Note · When the screen is showing one fixed image for a long time, the screen
brightness will be automatically reduced and then restored once the screen
content changes. This is a normal function to minimize image retention.
Running [Pixel Cleaning] to Protect the
OLED TV Screen
The OLED TV is equipped with a pixel cleaning feature to check the status of
the screen by itself and prevent image retention that leaves an image on a
screen. This feature automatically calculates the optimal execution time based
on the accumulated viewing time and is automatically executed when the TV is
turned off. While this feature is running, horizontal lines may appear at the
top and bottom of the screen. The pixel cleaning feature works when the
product is connected to the power cord and main power.
· To run this function manually, press the button on the remote control, go to
[ ] [General] [OLED Care] [OLED Panel Care] and press [Pixel Cleaning].
13
Regulatory
–
14
(1) (2) (3) (4)
NOTE TO CABLE/TV INSTALLER
(For USA and Canada) This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of the cable entry as
practical.
WARNING! (STABILITY HAZARD)
A television set may fall, causing serious personal injury or death. Many
injuries, particularly to children, can be avoided by taking simple
precautions such as:
– ALWAYS use cabinets or stands or mounting methods recommended by the
manufacturer of the television set. – ALWAYS use furniture that can safely
support the television set. – ALWAYS ensure the television set is not
overhanging the edge of the supporting furniture. – ALWAYS educate children
about the dangers of climbing on furniture to reach the television set or its
controls. – ALWAYS route cords and cables connected to your television so they
cannot be tripped over, pulled or grabbed. – NEVER place a television set in
an unstable location. – NEVER place the television set on tall furniture (for
example, cupboards or bookcases) without anchoring both the furniture and the
television set to a
suitable support. – NEVER place the television set on cloth or other materials
that may be located between the television set and supporting furniture. –
NEVER place items that might tempt children to climb, such as toys and remote
controls, on the top of the television or furniture on which the television
is placed. If the existing television set is going to be retained and
relocated, the same considerations as above should be applied.
Symbols
Refers to alternating current (AC). Refers to direct current (DC). Refers to
class II equipment.
Refers to stand-by. Refers to “ON” (power). Refers to dangerous voltage.
LG Take-back & Recycling Policy
15
16
OWNER’S MANUAL
EXTERNAL CONTROL DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com P/NO : MFL71445401 (1901-REV00)
2 KEY CODES
ENEGNLGISH
KEY CODES
· This feature is not available for all models.
Code (Hexa)
Function
00 CH +, PR +
01 CH -, PR –
02 Volume +
03 Volume –
06 > (Arrow Key / Right Key)
07 < (Arrow Key / Left Key)
08 Power
09 Mute
0B Input
0E SLEEP
0F TV, TV/RAD
10 – 19 * Number Key 0 – 9
1A Q.View / Flashback
1E FAV (Favorite Channel)
20 Text (Teletext)
21 T. Opt (Teletext Option)
28 Return (BACK)
30 AV (Audio / Video) Mode
39 Caption/Subtitle
40 (Arrow Key / Cursor Up)
41
V (Arrow Key / Cursor Down)
42 My Apps
43 Menu / Settings
44 OK / Enter
45 Q.Menu
4C List, –
4D PICTURE
52 SOUND
Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
Code (Hexa)
Function
53 List
5B Exit
60 PIP(AD)
61 Blue
63 Yellow
71 Green
72 Red
79 Ratio / Aspect Ratio
91 AD (Audio Description)
9E LIVE MENU
7A User Guide
7C Smart / Home
7E SIMPLINK
8E (Forward)
8F (Rewind)
AA Info
AB Program Guide
B0 (Play)
B1 (Stop / File List)
B5 RECENT
BA
(Freeze / Slow Play / Pause)
BB Soccer
BD (REC)
DC 3D
99 AutoConfig
9F App / *
9B TV / PC
Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
- Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel. (For South Korea, Japan, North America, Latin America except Colombia models)
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 3
EXTERNAL CONTROL DEVICE SETUP
· Image shown may differ from your TV.
Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an
external control device (such as a computer or an A/V control system) to
control the product’s functions externally.
Note: The type of control port on the TV can be different between model
series.
- Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB to Serial(RS-232C) converter with USB Cable
USB Type
(PC)
(TV)
USB IN
· LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008)
USB to serial(RS-232C) converter which is not made nor provided by LG.
· It can be purchased from computer stores that carry accessories for IT
support professionals.
RS-232C(Serial) With RS-232C(Serial) Cable
DE9 (D-Sub 9pin) Type · You need to purchase the RS-232C (DE9, D-Sub 9pin
female-to-female type) to RS-232C(Serial) cable
required for the connection between the PC and the TV, which is specified in
the manual.
(PC)
RS-232C IN
(CONTROL & SERVICE)
(TV)
The connection interface may differ from your TV.
4 EXTERNAL CONTROL DEVICE SETUP
ENEGNLGISH
Phone jack Type
· You need to purchase the phone-jack to RS-232 cable required for the
connection between the PC and the TV, which is specified in the manual.
- For other models, connect to the USB port. * The connection interface may differ from your TV.
SERVICE ONLY
1 3
(PC)
(TV)
2
– or
(PC)
1 3
2
RS-232C IN
(CONTROL & SERVICE)
(TV)
Customer Computer
1
5
RS-232C configurations
3-Wire Configurations(Not standard)
RXD
PC 2
TV 2 TXD
TXD 3 GND 5
1 RXD 3 GND
6
9
RS-232C (Serial port)
RXD TXD GND
OR 3 2 5
D-Sub 9
2 1 3 Phone
TXD RXD GND
Set ID For Set ID number, see “Real Data Mapping” on p.6
1. Press SETTINGS to access the main menus. 2. Press the Navigation buttons to scroll to (*General About this TV or OPTION) and press OK. 3. Press the Navigation buttons to scroll to SET ID and press OK. 4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99. 5. When you are finished, press EXIT.
- (Depending on model)
EXTERNAL CONTROL DEVICE SETUP 5
ENEGNLGISH
Communication Parameters
· Baud rate : 9600 bps (UART) · Data length : 8 bits · Parity : None
Command reference list
(Depending on model)
· Stop bit : 1 bit · Communication code : ASCII code · Use a crossed (reverse) cable.
COMMAND1
COMMAND2
DATA (Hexadecimal)
COMMAND1
COMMAND2
DATA (Hexadecimal)
01. Power* k
02. Aspect Ratio
k
03. Screen Mute
k
04. Volume Mute
k
05. Volume Control
k
06. Contrast k
07. Brightness
k
08. Color/ Colour
k
09. Tint
k
10. Sharpness
k
11. OSD Select
k
12. Remote Control Lock k Mode
13. Treble k
a
00 to 01
15. Balance k
t
16. Color
c
(p.7)
(Colour)
x
u
Temperature
17. ISM
d
(p.7)
Method (Only j
p
Plasma TV)
e
00 to 01
18. Equalizer j
v
f
00 to 64
19. Energy Saving
j
q
g
00 to 64
20. Tune Command
m
a
21. Channel m
b
h
00 to 64
(Programme)
Add/Del(Skip)
i
00 to 64
22. Key
m
c
23. Control m
g
j
00 to 64
Backlight, Control Panel
Light
k
00 to 32
24. Input
x
select (Main)
b
l
00 to 01
25. 3D (Only x 3D models)
t
26. Extended x
v
m
00 to 01
3D (Only 3D
models)
27. Auto
j
u
r
00 to 64
Configure
00 to 64 00 to 64
(p.8) (p.9) 00 to 05 (p.9) 00 to 01
Key Codes 00 to 64
(p.11) (p.11) (p.12)
(p.12)
14. Bass
k
s
00 to 64
- Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not executed and treated as NG. With RS232C cable, TV can communicate “ka command” in power-on or power-off status. but with USB-to-Serial converter cable, the command works only if TV is on.
6 EXTERNAL CONTROL DEVICE SETUP
ENEGNLGISH
Transmission / Receiving Protocol
Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV. [Set ID]
: You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to `0′, every connected set
can be controlled.
- [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA]
: To transmit command data (hexadecimal). Transmit `FF’ data to read status of command.
[Cr]
: Carriage Return – ASCII code `0x0D’
[ ]
: Space ASCII code `0x20′
OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The set
transmits ACK (acknowledgement) based on this format when receiving abnormal
data from non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
- When you enter the [data] in hexadecimal, refer to following conversion table. * Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0 01 : Step 1 (Set ID 1) … 0A : Step 10 (Set ID 10) … 0F : Step 15 (Set ID 15) 10 : Step 16 (Set ID 16) …
32 : Step 50 (Set ID 50) 33 : Step 51 (Set ID 51) … 63 : Step 99 (Set ID 99) … C7 : Step 199 C8 : Step 200 …
FE : Step 254 FF : Step 255 … 01 00 : Step 256 … 27 0E : Step 9998 27 0F : Step 9999 …
EXTERNAL CONTROL DEVICE SETUP 7
ENEGNLGISH
- Commands may work differently depending on model and signal.
01. Power (Command: k a) To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x] To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x]
- Similarly, if other functions transmit `FF’ data based on this format, Acknowledgement feedback presents status about each function.
Ack [d][ ][Set ID][ ][OK/NG][Data][x] * In case of video mute on only, TV will
display On Screen Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
04. Volume Mute (Command: k e) To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control. Transmission
[k][e][ ][Set ID][ ][Data][Cr] Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on) Ack [e][ ][Set ID][ ][OK/NG][Data][x]
02. Aspect Ratio (Command: k c) (Main Picture Size)
To adjust the screen format. (Main picture format) You can also adjust the
screen format using the Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen 07 : 14:9
(4:3)
(Europe, Colombia, Mid-East,
02 : Wide screen Asia except South Korea and
(16:9)
Japan)
04 : Zoom
09 : * Just Scan
05 : Zoom 2
0B : Full Wide
(Latin America
(Europe, Colombia, Mid-
except Colombia East, Asia except South
Only)
Korea and Japan)
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16
Original
0c : 21:9 (Depending on model)
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
- Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
- In DTV/HDMI/Component mode (high-definition), Just Scan is available.
- Full wide mode may work differently based on model and is supported for DTV fully, and ATV, AV partially.
03. Screen Mute (Command: k d) To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture
on) Video mute off
01 : Screen mute on (Picture off) 10 : Video mute on
05. Volume Control (Command: k f) To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [f][
][Set ID][ ][OK/NG][Data][x] 06. Contrast (Command: k g) To adjust screen
contrast.
You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [g][ ][Set ID][
][OK/NG][Data][x] 07. Brightness (Command: k h) To adjust screen brightness.
You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [h][ ][Set ID][
][OK/NG][Data][x]
8 EXTERNAL CONTROL DEVICE SETUP
ENEGNLGISH
08. Color/Colour (Command: k i) To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu. Transmission [k][i][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [i][ ][Set ID][
][OK/NG][Data][x] 09. Tint (Command: k j) To adjust the screen tint.
You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][
][Data][Cr] Data Red : 00 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k) To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l) To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m) To lock the front panel controls
on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
- If you are not using the remote control, use this mode. When main power is off & on (plug-off and plug-in, after 20 – 30 seconds), external control lock is released.
- In the standby mode (DC off by off timer or
ka’,
mc’ command), and if key lock is on, TV will not turn on by power on key of IR & Local Key.
13. Treble (Command: k r) To adjust treble.
You can also adjust in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
14. Bass (Command: k s) To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
15. Balance (Command: k t) To adjust balance.
You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][
][Data][Cr] Data Min : 00 to Max : 64 Ack [t][ ][Set ID][ ][OK/NG][Data][x]
16. Color(Colour) Temperature (Command: x u) To adjust colour temperature.
You can also adjust
Color(Colour) Temperature in the PICTURE menu. Transmission [x][u][ ][Set ID][
][Data][Cr] Data Min : 00 to Max : 64 Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. ISM Method (Command: j p) (Only Plasma TV) To control the ISM method. You
can also adjust
ISM Method in OPTION menu. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data
Min : 02: Orbiter
08: Normal 20: Color(Colour) Wash Ack [p][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP 9
ENEGNLGISH
18. Equalizer (Command : j v)
Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
LSB
0000000 0
Frequency
Data
7 6 5 Frequency 4 3 2 1 0
Step
0 0 0 1st Band 0 0 0 0 0 0(decimal)
0 0 1 2nd Band 0 0 0 0 1 1(decimal)
0 1 0 3rd Band … … … … …
…
0 1 1 4th Band 1 0 0 1 1 19(decimal)
1 0 0 5th Band 1 0 1 0 1 20(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
- It depends on model, and can adjust when sound mode is EQ adjustable value.
19. Energy Saving (Command: j q)
To reduce the power consumption of the TV. You can also adjust Energy Saving
in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr] Data 00 : Off 01 : Minimum 02 :
Medium 03 : Maximum 04 : Auto (For LCD TV / LED TV) / Intelligent sensor (For
PDP TV) 05 : Screen off
- (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
20. Tune Command (Command: m a)
-
This command may work differently depending on model and signal.
· For Europe, Mid-East, Colombia, Asia except South Korea and Japan Model
Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ] [Data 01][ ][Data 02][Cr] -
Analog Antenna/Cable
[Data 00][Data 01] Channel Data Data 00 : High byte channel data Data 01 : Low byte channel data
– 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog) – 00 : Antenna TV (ATV) – 80 : Cable TV (CATV) -
Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data Data 00 : High Channel data Data 01 : Low Channel data
– 00 00 ~ 27 0F (Decimal: 0 ~ 9999) Data 02 : Input Source (Digital)
– 10 : Antenna TV (DTV) – 20 : Antenna Radio (Radio) – 40 : Satellite TV (SDTV) – 50 : Satellite Radio (S-Radio) – 90 : Cable TV (CADTV) – a0 : Cable Radio (CA-Radio) -
Tune Command Examples: 1. Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00 Data 00 & 01 = Channel Data is 10 = 00 0a Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00
2. Tune to the digital antenna (DVB-T) Channel 01. Set ID = All = 00 Data 00 & 01 = Channel Data is 1 = 00 01 Data 02 = Digital Antenna TV = 10 Result = ma 00 00 01 10
3. Tune to the satellite (DVB-S) Channel 1000. Set ID = All = 00 Data 00 & 01 = Channel Data is 1000 = 03 E8 Data 02 = Digital Satellite TV = 40 Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][x][a][ ][Set ID][ ][NG][Data 00][x] · For South Korea, North/Latin America except Colombia Model
To tune channel to following physical/major/minor number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr] Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel from the Major / Minor number, the Physical number is not required when sending a command in Digital.
10 EXTERNAL CONTROL DEVICE SETUP
ENEGNLGISH
- Analog Antenna/Cable
Data 00 : Physical Channel Number – Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) – Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number Data 01 & 02: xx (Don’t care) Data 03 & 04: xx (Don’t care) Data 05: Input Source (Analog)
– 00 : Antenna TV (ATV) – 01 : Cable TV (CATV) - Digital Antenna/Cable
Data 00 : xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor Channel Number Data 03 : High byte Channel Data Data 04 : Low byte Channel Data
Data 05 : Input Source (Digital) – 02 : Antenna TV (DTV) Use Physical Channel Number – 06 : Cable TV (CADTV) Use Physical Channel Number – 22 : Antenna TV (DTV) Don’t Use Physical Channel Number – 26 : Cable TV (CADTV) – Don’t Use Physical Channel Number – 46 : Cable TV (CADTV) Use Physical/Major Channel Number Only (One Part Channel) – 66 : Cable TV (CADTV) Use Major Channel Number Only (One Part Channel) – 0b : Cable DTV Plus Use Physical Channel Number – 2b : Cable DTV Plus Don’t Use Physical Channel Number – 4b : Cable DTV Plus Use Physical/Major Channel Number Only (One Part Channel) – 6b : Cable DTV Plus Use Major Channel Number Only (One Part Channel)
Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0). - Tune Command Examples: 1. Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00 Data 00 = Channel Data is 35 = 23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data 05 = Analog Cable TV = 01 Total = ma 00 23 00 00 00 00 01
2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00
= Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 =
Minor is 3 = 00 03 Data 05 = Digital Antenna TV = 22 Total = ma 00 00 00 1E 00
03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data
05] [x][a][ ][Set ID][ ][NG][Data 00][x] · For Japan Model To tune channel to
following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][
][Data04][ ][Data05][Cr] * Digital Antenna/Satellite Data 00: xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01: High byte Channel Data Data
02: Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number (Don’t care in Satellite)
Data 03: High byte Channel Data Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan) – 02 : Antenna TV (DTV) –
42 : Antenna TV (DTV) Use Physical/Major Channel Number Only (One Part
Channel) – 62 : Antenna TV (DTV) Use Major Channel Number Only (One Part
Channel) – 07 : BS (Broadcasting Satellite) – 08 : CS1 (Communication
Satellite 1) – 09 : CS2 (Communication Satellite 2)
- Tune Command Examples: 1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 17 = 00 11 Data 03 & 04 = Minor/Branch is 1 = 00 01 Data 05 = Digital Antenna TV = 02 Total = ma 00 00 00 11 00 01 02
EXTERNAL CONTROL DEVICE SETUP 11
ENEGNLGISH
2. Tune to the BS (ISDB-BS) channel 30. Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Don’t Care = 00 00 Data 05 = Digital BS TV = 07 Total = ma 00 00 00 1E 00 00 07
- This feature is varied based on the model. Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data 05] [x][a][ ][Set ID][ ][NG][Data 00][x] 21. Channel(Programme) Add/Del(Skip) (Command: m b)
To skip current channel(programme) for next time. Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x] * Set the saved channel status to del(ATSC, ISDB)/ skip(DVB) or add.
22. Key (Command: m c) To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code – p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x] 23. Control Backlight (Command: m g) · For LCD TV / LED TV To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x] Control Panel Light (Command: m g)
· For Plasma TV To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
24. Input select (Command: x b) (Main Picture Input)
To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
00 : DTV
01 : CADTV
02 : Satellite DTV
10 : ATV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
20 : AV or AV1
21 : AV2
40 : Component1 60 : RGB
41 : Component2
90 : HDMI1 92 : HDMI3
91 : HDMI2 93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
- This function depends on model and signal.
25. 3D(Command: x t) (only 3D models) (Depending on model)
To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01] [ ][Data 02][ ][Data
03][Cr] (Depending on model) Data Structure [Data 00] 00 : 3D On
01 : 3D Off 02 : 3D to 2D 03 : 2D to 3D [Data 01] 00 : Top and Bottom 01 :
Side by Side 02 : Check Board 03 : Frame Sequential 04 : Column interleaving
05 : Row interleaving [Data 02] 00 : Right to Left 01 : Left to Right [Data
03] 3D Effect(3D Depth): Min : 00 – Max : 14 (transmit by Hexadecimal code)
12 EXTERNAL CONTROL DEVICE SETUP
ENEGNLGISH
- [Data 02], [Data 03] functions depend on model and signal.
- If [Data 00] is 00 (3D On), [Data 03] has no meaning.
- If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data 01], [Data 02] and [Data 03] have no meaning.
- If [Data 00] is 03 (2D to 3D), [Data 01] and [Data 02] have no meaning.
- If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data 03] works when 3D Mode (Genre) is manual only.
- All 3D pattern options ([Data 01]) may not be available according to broadcasting/video signal.
[Data 00] 00 01 02 03 [Data 01] O X X X
X : don’t care
[Data 02] O X X O [Data 03] O X X O
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] [Data03][x] [t][ ][Set ID][ ][NG][Data00][x]
26. Extended 3D(Command: x v) (only 3D models) (Depending on model)
To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ] [Data 01][Cr] [Data 00] 3D
option 00 : 3D Picture Correction 01 : 3D Depth (3D Mode is Manual Only) 02 :
3D Viewpoint 06 : 3D Color Correction 07 : 3D Sound Zooming 08 : Normal Image
View 09 : 3D Mode (Genre)
[Data 01] It has own range for each 3D option determined by [Data 00].
-
When [Data 00] is 00 00 : Right to Left 01 : Left to Right
-
When [Data 00] is 01, 02 Data Min: 0 – Max: 14 (transmit by Hexadecimal
code) Data value range(0 – 20) converts Viewpoint range (-10 – +10) automatically (Depending on model) This option works when 3D Mode (Genre) is manual
only. -
When [Data 00] is 06, 07 00 : Off 01 : On
-
When [Data 00] is 08 00 : Revert to 3D video from 3D-to-2D converted 2D video 01 : Change 3D video to 2D video, except 2D-to-3D video
- If conversion condition doesn’t meet, command is treated as NG.
- When [Data 00] is 09
00 : Standard 02 : Cinema 04 : Manual
01 : Sport 03 : Extreme 05 : Auto
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x] [v][ ][Set ID][ ][NG][Data00][x]
27. Auto Configure (Command: j u) (Depending on model)
To adjust picture position and minimize image shaking automatically. It works
only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : To set Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
References
- Consumer Electronics, Home & Kitchen Appliances | LG Australia
- LG Electronics & Home Appliances | Shop Now | LG USA
- LG Electronics & Home Appliances | Shop Now | LG USA
- Arbitration | LG USA
- LG Open Source
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>