Alliance Laundry Systems DR7004WG Electric Dryer Instruction Manual

Alliance Laundry Systems DR7004WG Electric Dryer

WARNING

• Risk of fire. Highly flammable material.
• Read all instructions before using unit.
• FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or ex-plosion or to prevent property damage, personal in-jury or death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building or area of all occu-pants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s in-structions.
• If you cannot reach your gas supplier, call the fire department.
• Installation and service must be performed by a qualified installer, service agency or the gas sup-plier.
• IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be followed if the dryer user smells gas. The gas utility instructions plus the
• SAFETY and WARNING note directly above must be posted in a prominent location near the dryer for customer use.
• Installation of unit must be performed by a quali-fied installer.
• Install clothes dryer according to manufacturer’s instructions and local codes.
• DO NOT install a clothes dryer with flexible plas-tic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suita-ble for use with clothes dryers. Refer to section on connecting exhaust system. Flexible venting materials are known to collapse, be easily crush-ed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.
• To reduce the risk of severe injury or death, follow all installation instructions. Save these instructions.

FOR YOUR SAFETY

• Do not store or use gasoline or other flammable va-pors and liquids in the vicinity of this or any other appliance.
• This product uses FreeRTOS V7.2.0 ( www.freertos.org).
• The following information applies to the state of Massachusetts, USA.
• This appliance can only be installed by a Massachusetts li-censed plumber or gas fitter.
• This appliance must be installed with a 36 inch [910 mm] long flexible gas connector.
• A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.
• This appliance must not be installed in a bedroom or bath-room.

Dimensions

Knob Control: * 40.75 [1035 mm]

E| 42.75 in. [1086 mm]
F| 15.4 in. [391 mm]
G| 15.44 in. [392 mm]
H| 26.875 in. [683 mm]
I| 4.0 in. [102 mm]
J| 0.4 in. [11 mm]
K| 4.5 in. [114 mm]
L| 28 in. [711 mm]
M| 23.5 in. [597 mm]
NOTE: Exhaust openings are 4 inch [102 mm] metal ducting.| * With leveling legs turned into base.

Gas Dryers

Knob Control: * 40.75 [1035 mm]

E| 42.75 in. [1086 mm]
F| 15.4 in. [391 mm]
G| 15.44 in. [392 mm]
H| 2.8 in. [70 mm]
I| 2.3 in. [60 mm]
J| 26.875 in. [683 mm]
K| 4 in. [102 mm]
L| 0.4 in. [10 mm]
M| 4.5 in. [114 mm]
N| 28 in. [711 mm]
O| 23.5 in. [597 mm]
NOTE: Exhaust openings are 4-inch [102 mm] metal ducting.| With leveling legs turned into a base.

Installation

Before You Start Supplies

For most installations, the basic supplies you will need are:

1. Wrench
2. 1/4 inch Driver
3. Screwdrivers
4. Level
5. Gloves
6. Teflon Tape
7. Duct Tape
8. Safety Glasses

Figure 1

NOTE: This appliance is suitable for use in countries having a warm, damp climate.

WARNING

Any disassembly requiring the use of tools must be performed by a suitably qualified service person.

Parts Included

• An accessories bag has been shipped inside your dryer. It in-cludes:
• Product literature.
• Lint Filter Guard (optional accessory).
• Three screws (electric dryers only). Refer to Electric Dryer

Only – Connect Electrical Plug.

• One filter screen washer (steam models only). Refer to Steam

Dryers – Connect Water Inlet Hose.

• One plain rubber washer (steam models only). Refer to Steam

Dryers – Connect Water Inlet Hose.

Parts Needed

Item| Quantity| Notes
Fill/Inlet Hose, Dryer| 1| Must be sourced separately
Y-Connector| 1| Must be sourced separately
Rubber washer| 1| Must be sourced separately
Extension/Fill Hose| 1; Optional| Must be sourced separately

• Refer to the following specifications when sourcing fill/inlet hoses:
• Hoses must be new.
• Hoses must be a minimum of 3/8 in. inside diameter. Smaller inside diameter hoses will cause long fill times which could create nuisance fill errors.
• The plain rubber washers and filter screens included with the washer in the accessories bag must be installed in the fill hose couplings. The filter screens help prevent foreign materials from clogging the water mixing valve.
• Refer to Steam Dryers – Connect Water Inlet Hose for more details.

Order of Installation Steps

1. Position and level the dryer.
2. Steam models only, connect the water inlet hose.
3. Connect dryer to exhaust system.
4. For gas models only, connect the gas supply pipe. Check for gas leaks.
5. For electric models only, connect the electrical cord.
6. Reverse the door, if desired.
7. Wipe out the inside of the dryer.
8. Plug in the dryer.
9. Recheck steps.
10. Start and run the dryer in a heat setting to verify dryer is heating.

Position and Level the Dryer

1. Install dryer before washer. This allows room for attaching exhaust duct.
2. Select a location with a solid floor. Dryers installed in residential garages must be elevated 18 inches [457 mm] above the floor. No other fuel burning appliance should be installed in the same closet with the dryer. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. All four legs must rest firmly on the floor so the weight of the dryer is evenly distributed. The dryer needs sufficient clearance and an adequate air supply for proper operation and ventilation, and for easier installation and servicing. (Minimum clearances are shown in Figure 3 ).
3. Place the dryer in position, and adjust the legs until the dryer is level from side to side and front to back. The dryer must not rock.
4. Dryer Base
5. Level
6. Leveling Leg

Installation

1. Closet Door
2. Centered Air Openings (G) (2 Openings minimum)
3. Outer Wall of Enclosure

Area

|

Description

| Free Standing/Alcove In- stallation|

Closet Installation

---|---|---|---
A| Dryer sides and rear clearance| 0 in. [0 mm]| 0 in. [0 mm]
B| Dryer top clearance| 12.25 in. [305 mm]| 12.25 in. [305 mm]
C| Dryer front clearance| Not Applicable| 2 in. [51 mm]
D| Exhaust duct clearance to com- bustible material| 2 in. [51 mm]| 2 in. [51 mm]
E| Weather hood to ground clear- ance| 12 in. [305 mm]| 12 in. [305 mm]
F| Distance from floor or ceiling to air opening edge| Not Applicable| 3 in. [76 mm]
G| Area of centered air openings in closet door. Louvered door with equivalent air openings is acceptable. (Minimum clearan- ces are shown.)| Not Applicable| 40 sq. in./open [260 sq. cm/ open]
H| For new installations, locate top of wall vent 42 inches [1067 mm] above the floor to make venting easier to connect.| 42 in. [1067 mm]| 42 in. [1067 mm]
| Rear clearance is minimum. 2 inches [51 mm] is recommended for utility connection. 6 inches [152 mm] is recommended when venting through the rear of the unit.

Table 1

• NOTE: For new installations, it is suggested to locate top of wall vent 42 inches (106.7 cm) above floor to make venting easier to connect.
• IMPORTANT: In mobile home installations, gas dryers MUST be permanently attached to the floor at the time of installation. Order No. 526P3 Dryer Installation Kit (available at extra cost) for a manufactured (mobile) home installation. Follow the instructions supplied with the kit.

Steam Dryers – Connect Water Inlet Hose

• If re-using the washer fill hose filter screen on an already installed washing machine, it must be cleaned before installing the steam connection. Turn on the water supply faucet and flush the line for approximately two minutes to remove any foreign materials that could clog the screen in the water valve. This is especially important when installing your steam dryer in a newly constructed or renovated building. Build-up may have occurred during construction.
• NOTE: Y-connector, extension/fill hose(s) and rubber washer for Y-Connector are not included with the dryer.

1. Turn off water at shut-off valve.

2. Remove the plain rubber washer and filter screen from the accessories bag.

3. Disconnect cold-water inlet hose from water supply if washing machine is connected.

4. Insert rubber washer into Y-connector (both sold separately).

5. Install Y-connector onto cold-water supply (use extension hose if Y-connector cannot be installed directly on water supply).

6. Insert filter screen on the faucet end of inlet hose with the screen facing outward towards the faucet and the rubber washer on the valve end of the hose.

7. Connect filter screen end of the inlet hose to the Y-Connector.

8. Connect the rubber washer end of inlet hose to the fill valve on rear of dryer, thread hose coupling finger tight. Then turn 1/4 turn with pliers.
   IMPORTANT: Do NOT cross thread or overtighten couplings. This will cause them to leak.

9. Connect/Reconnect washer inlet hose to the other end of Yconnector, thread hose coupling finger tight. Then turn 1/4 turn with pliers.

10. If installing new washing machine, connect hose to unit. Refer to washing machine install instructions.

11. Check that Y-connector valves are open (if applicable).

12. Turn water on and check for leaks. Wait 30 minutes and check again, some leaks are slow to show up.

13. If leaks are found, check and retighten the hose couplings.

NOTE: If leaks persist after checking and retightening hose coupling, check for crossing threading, and damaged hose(s) or rubber washer(s).

1. Faucet
2. Rubber Washer
3. Filter Screen
4. Install this end to faucet
5. Install this end to valve at rear of dryer
6. Water Fill Valve
7. Dryer Rear Panel
8. Washer Rear Panel
9. Inlet Hose

Figure 4 Installing Inlet Hose – Y-Connector on Water Supply:

1. Faucet
2. Filter Screen
3. Rubber Washer
4. Install this end to Y-connector
5. Install this end to valve at rear of dryer
6. Water Fill Valve
7. Dryer Rear Panel
8. Washer Rear Panel
9. Inlet Hose
10. Extension Hose

IMPORTANT:

• Hoses and other rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subjected to.
• All hoses should be checked on a monthly basis for any visible signs of deterioration. Any hose showing the signs of deterioration listed above should be replaced immediately. All hoses should be replaced every five years

Connect Dryer Exhaust System

To reduce the risk of fire and combustion gas accu- mulation the dryer MUST be exhausted to the out- doors.

W604

To reduce the risk of fire and the accumulation of combustion gases, DO NOT exhaust dryer air into a window well, gas vent, chimney or enclosed, unven- tilated area, such as an attic, wall, ceiling, crawl space under a building or concealed space of a building.

W045

This gas appliance contains or produces a chemical or chemicals which can cause death or serious ill- ness and which are known to the State of California to cause cancer, birth defects, or other reproductive harm. To reduce the risk from substances in the fuel or from fuel combustion, make sure this appliance is installed, operated, and maintained according to the instructions in this manual.

W115

To reduce the risk of fire, DO NOT use plastic or thin foil ducting to exhaust the dryer.

W354

To reduce the risk of fire, the exhaust duct and weather hood MUST be fabricated of a material that will not support combustion. Rigid or flexible metal pipe is recommended for a clothes dryer.

W048

Risk of fire. Do not install a booster fan in the exhaust duct.

W1072

• NOTE: The booster fan warning does not apply to clothes dryers intended to be installed in a multiple clothes dryer system, with an engineered exhaust duct system that is installed per the clothes dryer manufacturer’s guidelines.

• DO NOT use plastic, thin foil or type B ducting. Rigid metal duct is recommended.

• Locate dryer so exhaust duct is as short as possible.

• Be certain old exhaust ducts are cleaned before installing your new dryer.

• Use 4 inch [102 mm] diameter rigid or flexible metal duct.

• The male end of each section of duct must point away from the dryer.

• Use as few elbows as possible.

• Use of duct tape or pop-rivets on all seams and joints is recommended, if allowed by local codes. DO NOT use sheet metal screws or fasteners on exhaust pipe joints which extend into the duct and catch lint.

• uctwork that runs through unheated areas must be insulated to help reduce condensation and lint build-up on pipe walls.

• In mobile home installations, dryer exhaust duct must be secured to mobile home structure.

• Dryer exhaust duct MUST NOT terminate under mobile home.

• Exhaust duct must not be connected to any other duct, vent, or chimney.

• Dryer exhausts 220 cfm per unit (measured at back of dryer).

• DO NOT install flexible duct in concealed spaces, such as a wall or ceiling.

• Static pressure in exhaust duct should not be greater than 0.6 inches water column [1.5 cm water column] , measured with manometer placed on exhaust duct 2 feet [610 mm] from dryer (check with dryer running and no load).

• Exhausting dryer in hard-to-reach locations can be done by installing 521P3 Flexible Metal Vent Kit (available as optional equipment at extra cost).

• Sufficient make-up air must be supplied to replace the air exhausted by the dryer. The free area of any opening for outside air must be at least 40 in. 2 [25806 mm 2 ] per unit.

• Failure to exhaust dryer properly will void warranty.

• A dryer will dissipate 60 Btu/ft 2 [681,392 J/m 2 ] of surface area exposed to the conditioned air.

• NOTE: Venting materials are not supplied with the dryer (obtain locally).

• IMPORTANT: DO NOT block the airflow at the bottom of the dryer’s front panel with laundry, rugs, etc. Blockage will decrease airflow through the dryer, thus reducing the efficiency of the dryer.

• Exhaust Direction
  The dryer can be exhausted to the outdoors through the back, left,
  right or bottom of the dryer. EXCEPTION: Gas dryers cannot be
  vented out the left side because of the burner housing.
  Dryer is shipped from factory ready for rear exhaust.
  Exhausting the dryer through sides or bottom can be accomplished
  by installing a Directional Exhaust Kit, 528P3, available as
  optional equipment at extra cost.
  Exhaust System
  For best drying results, recommended maximum length of exhaust system is shown in Table 2 .

• To prevent backdraft when dryer is not in operation, outer end of exhaust pipe must have a weather hood with hinged dampers (obtain locally).

• NOTE: Weather hood should be installed at least 12 inches [305 mm] above the ground. Larger clearances may be necessary for installations where heavy snowfall can occur.

Number of 90° Elbows

| Weather Hood Type
---|---
Recommended| Use Only for Short Run Installations
 | **|
The maximum length of 4 in. [102 mm] diameter rigid metal duct.**
0| 65 feet [19.8 m]| 55 feet [16.8 m]
1| 55 feet [16.8 m]| 47 feet [14.3 m]
2| 47 feet [14.3 m]| 41 feet [12.5 m]
3| 36 feet [11.0 m]| 30 feet [9.1 m]
4| 28 feet [8.5 m]| 22 feet [6.7 m]

• NOTE: Deduct 6 feet [1.8 m] for each additional elbow
• NOTE: The maximum length of a 4 in. [102 mm] diame-ter flexible metal duct must not exceed 7.87 ft. [2.4 m] , as required to meet UL2158, clause 7.3.2.A.

Gas Dryers – Connect Gas Supply Pipe

• WARNING
• To reduce the risk of gas leaks, fire or explosion:
• The dryer must be connected to the type of gas as shown on nameplate located in the door re-cess.
• Use a new flexible stainless steel connector.
• Use pipe joint compound insoluble in L.P. (Liquefied Petroleum) Gas, or Teflon tape, on all pipe threads.
• Purge air and sediment from gas supply line be-fore connecting it to the dryer. Before tightening the connection, purge remaining air from gas line to dryer until odor of gas is detected. This step is required to prevent gas valve contamination.
• Do not use an open flame to check for gas leaks. Use a non-corrosive leak detection fluid.
• Any disassembly requiring the use of tools must be performed by a suitably qualified service per-son.

1. Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory for

• Natural Gas with a 3/8 inch NPT gas connection.
• NOTE: The gas service to a gas dryer must conform with the local codes and ordinances, or in the absence of local codes and ordinances, with the latest edition of the National Fuel Gas Code ANSI Z223.1/ NFPA 54 or the CAN/CSA-B149.1 Natural Gas and Propane Installation Code.
• Natural Gas, 1000 Btu/ft 3 [37.3 MJ/m 3 ] , service must be supplied at minimum 5.0 inch water column pressure to maximum 10.5 inch water column pressure. For proper operation at altitudes above 3000 feet [915 m] the natural gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 3 .

Natural Gas Altitude Adjustments

Altitude| Orifice Size|

Part No.

feet [m]| No.| inches [mm]
3000 [915]| 43| 0.0890 [2.26]| D503778
6000 [1830]| 44| 0.0860 [2.18]| 58719
8000 [2440]| 45| 0.0820 [2.08]| D503779
9000 [2740]| 46| 0.0810 [2.06]| D503780
10,000 [3050]| 47| 0.0785 [1.99]| D503781

1. Remove the shipping cap from the gas connection at the rear of the dryer. Make sure you do not damage the pipe threads when removing the cap.
2. Connect to gas supply pipe using thread sealant or Teflon tape. Torque 90 – 175 inch-pounds [10.2 – 19.7 Nm] .

• NOTE: The connection of gas supply to the appliance shall be made with a flexible hose suitable for the appliance category in accordance with national installation regulations of the country of destination.
• If in doubt contact the dryer distributor or manufacturer.
• NOTE: When connecting to a gas line, an equipment shut-off valve in accordance with the National Fuel
• Gas Code, ANSI Z223.1/NFPA 54 and the Natural
• Gas and Propane Installation Code, CSA B149.1 must be installed within 6 feet [1.8 m] of the dryer.
• An 1/8 in. NPT pipe plug must be installed as shown for checking inlet pressure. Refer to Figure 7 .
• Starting Serial No. 1908000001, the following must be furnished and installed by the customer for the gas service line to dryer:
• Union at gas supply connection (listed to ANSI Z21.24 and CSA 6.10).

1. New Stainless Steel Flexible Connector – (Use design CSA certified connector) Use only if allowed by local codes
2. 1/8 in. NPT Pipe Plug
3. Equipment Shut-Off Valve
4. Black Iron Pipe: Shorter than 20 ft. [6.1 m] – Use 3/8 in. [9.5 mm] pipe. Longer than 20 ft. [6.1 m] – Use 1/2 in. [12.7 mm] pipe. 3/8 in. NPT Gas Connection

• Tighten all connections securely but don’t overtighten to avoid breaking or bending the gas valve bracket. Turn on gas and check all pipe connections (internal & external) for gas leaks with a non-corrosive leak detection fluid.
• NOTE: The dryer and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi [3.45 kPa] . Refer to Check Heat Source.
• NOTE: DO NOT connect the dryer to L.P. Gas Service without converting the gas valve. Install L.P. Gas Conversion Kit 649P3, available at extra cost.

1. L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft. 3 [93.1 MJ/m 3 ] , service must be supplied at 10 ± 1.5 inch water column pressure.
2. For proper operation at altitudes above 3000 feet [915 m] the L.P. gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 4 .

L.P. Altitude Adjustments

Altitude| Orifice Size|

Part No.

feet [m]| No.| inches [mm]
3000 [915]| 55| 0.0520 [1.32]| 58755
8000 [2440]| 56| 0.0465 [1.18]| D503786

Connect Electrical Plug (Electric DryerOnly)

• Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz, 3 or 4 wire electrical supply. Refer to the serial plate for specific electrical requirements.
• IMPORTANT: Use only a new U.L. listed No. 10 (copper wire only) three or four conductor power supply cord kit rated 240 Volts (minimum) 30 Amperes and labeled as suitable for use in a clothes dryer.
• NOTE: The wiring diagram is located in the control hood.

WARNING

• To reduce the risk of fire, electric shock, serious injury, or death, all wiring, and grounding MUST conform with the latest edition of the National Electrical
• Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1, and such local regulations as might apply. It is the customer’s responsibility to have the wiring and fuses installed by a qualified electrician to make sure adequate electrical power is available to the dryer.

Grounding Information

• This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance to electric current. The cord kit must be equipped with a cord having an equipment-grounding conducator and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the dryer is properly grounded.
• Do not modify the plug proivded with the cord-kit – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
• The dryer has its own terminal block that must be connected to a separate branch, 60 Hertz, single phase circuit, AC (alternating current) circuit, fused at 30 Amperes (the circuit must be fused on both sides of the line). Electrical service for the dryer should be of maximum rated voltage (208 or 240 Volt, depending on heating element) listed on the nameplate. Do not connect dryer to 110, 115, or 120 Volt circuit.Heating elements are available for field installation in dryers which are to be connected to electrical service of different voltage than that listed on nameplate, such as 208 Volt.
• NOTE: Branch circuit wire size requirements to laundry room outlet are shown in table below.

• The power cord connection between wall receptacle and the dryer terminal block IS NOT supplied with the dryer. The type of power cord and gauge of wire must conform to local codes.

Connecting Power Cord with Three-Wire Plug

• NOTE: Four-wire cord is required for new branch-circuit installations, mobile homes, or where codes do not permit grounding through neutral.
• NOTE: The power cord is NOT supplied with the electric dryer. The type of power cord and gauge of wire must conform to local codes and instructions.
• The method of wiring the dryer is optional and subject to local code requirements.
• NOTE: Connect the dryer to the power supply with the
• MAXIMUM RATED VOLTAGE listed on the serial plate.
• NOTE: Use COPPER WIRE only.
• Shorter than 15 ft. (4.5 m) – use 10 AWG
• Longer than 15 ft. (4.5 m) – use 8 AWG

1. A typical 30-Amp Three-Wire Receptacle NEMA Type 10-30R
2. 120 ± 12 V.A.C.
3. 240 ± 12 V.A.C.
4. Intermediate Fuse Box (may be omitted if service entrance box is fused)
5. Wall Receptacle
6. Power Supply
7. 3-Wire Earth/Ground Neutral 120/240 Volt, 60 Hertz AC 1 Phase Service Entrance Switch Box (Refer to NOTE above)
8. 30 Ampere Fuses or Circuit Breaker
9. Neutral Wire
10. Metallic or Non-Metallic Sheathed Cable (Copper Wire Only)
11. Power Cord (Not supplied with dryer)
12. Neutral
13. Terminal Block in Dryer
14. Intermediate Shut-Off Box (may or may not be fused)
15. Direct Connection
16. Power Cord Connection

Figure 8

1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
3. Use a strain relief and insert the end of the power cord through the power supply hole.
4. Use the three screws from the accessories bag to attach the power cord wires to the terminal block. Refer to Figure 11.

3-Wire Connection

1. “L1” Terminal

2. Neutral Terminal

3. “L2” Terminal

4. Earth/Ground to Bulkhead

   • Figure 11

5. Using a screwdriver, tighten all screws firmly.
   IMPORTANT: Failure to tighten these screws firmly may result in wire failure at the terminal block.

6. Secure the strain relief to the power cord, or wires, where they enter the dryer cabinet.

7. Check the continuity of the earth/ground connection before plugging the cord into an outlet. Use an acceptable indicating device connected to the center earth/ground pin of the plug and the green screw on the back of the cabinet.

8. Reinstall the access cover and screw.

Connecting Power Cord with Four-Wire Plug
NOTE: Four-wire cord is required for new branch-circuit installations, mobile homes, or where codes do not permit grounding through neutral.

1. Typical Four-Wire Receptacle
2. Power Cord – Not Supplied with Dryer
3. Strain Relief Nut
4. Strain Relief
5. 0 V.A.C.
6. 240 ± 12 V.A.C.
7. 120 ± 12 V.A.C.

Figure 12

1. Disconnect power to dryer.
2. Remove access cover from rear of dryer.
3. Remove the earth/ground screw from the earth/ground to neutral wire and save for use in Step 5. Earth/ground to the neutral wire will be attached to the neutral terminal in Step 6.
4. Earth/Ground Screw

  *  **Figure 14**

4. Use a strain relief and insert end of power cord through power supply hole.
   • Figure 15
5. Attach power cord earth/ground (green) wire to rear bulkhead using earth/ground screw removed in Step 3.

4-Wire Connection

1. Neutral Terminal

2. “L2” Terminal

3. Black

4. White

5. Earth/Ground

6. Red

7. “L1” Terminal

8. Earth/Ground to Neutral Wire Figure 16

9. Use the three screws from the accessories bag to attach the remaining power cord wires to the terminal block as follows:

   • a. Red wire to “L1” terminal.
   • b. Black wire to “L2” terminal.
   • c. White wire to Neutral terminal.
   • NOTE: When installing the white wire, loop the free eyelet end of the earth/ground to neutral wire (removed in Step 3) and attach along with the white wire to the neutral (center) terminal on the terminal block.

10. Using a screwdriver, tighten all screws firmly.
    IMPORTANT: Failure to tighten these screws firmly may result in wire failure at the terminal block.

11. Secure the strain relief to the power cord, or wires, where they enter the dryer cabinet.

12. Check the continuity of the earth/ground connection before plugging the cord into an outlet. Use an acceptable indicating device connected to the center earth/ground pin of the plug and the green screw on the back of the cabinet.

Reinstall the access cover and screw. Reverse Door, if Desired
NOTE: Doors with windows cannot be reversed.

The door on this dryer is completely reversible. To reverse the door proceed as follows:

1. Remove four hinge-attaching screws.
2. Remove all nine screws
3. Pull bottom of door liner out, then pull down, removing door liner from door panel.
4. Rotate door panel 180 degrees as shown
5. Remove door strike from door liner and reinstall on opposite side
6. Insert liner under flange on bottom of door, then push top of door liner into place
7. Reinstall nine screws removed in Step 2.
8. Using screwdriver, remove two door plugs, and reinstall on opposite side of door opening.
9. Reinstall four hinge attaching screws, removed in Step 1.

Wipe Out Inside of Dryer

Before using dryer for the first time, use an all-purpose cleaner, or a detergent and water solution, and a damp cloth to remove shipping dust from inside dryer drum.

Plug In the Dryer

This appliance is to be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.

WARNING

The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility.

Electric Dryer

• Connect the dryer to an electrical power source. Refer to Electric
• Dryer Only – Connect Electrical Plug for information on connecting power cord.

Gas Dryers

• Dryer requires 120 Volt, 60 Hertz electrical supply and comes equipped with a 3-prong grounding plug. Refer to serial plate for specific electrical requirements.
• NOTE: The wiring diagram is located in the control hood.

WARNING

• To reduce the risk of fire, electric shock, serious injury or death, all wiring and grounding MUST conform with the latest edition of the National Electrical Code,
• ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1, and such local regulations as might apply. It is the customer’s responsibility to have the wiring and fuses installed by a qualified electrician to make sure adequate electrical power is available to the dryer.

WARNING

• This dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

WARNING

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the dryer is properly grounded.
• Do not modify the plug provided with the dryer – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
• NOTE: Have a qualified electrician check the polarity of the wall receptacle. If a voltage reading is measured other than that listed on the dryer’s nameplate, the qualified electrician should correct the problem.
• Do not operate other appliances on the same circuit when this appliance is operating.

WARNING

• To reduce the risk of an electric shock or fire, DO NOT use an extension cord or an adapter to connect the dryer to the electrical power source.

Plug cord into separately fused 15 Amp circuit.

1. “L1”
2. Earth/Ground
3. Neutral Side
4. Neutral Side
5. Round Earth/Ground Prong
6. 0 V.A.C.
7. 120±12 V.A.C.
8. 120±12 V.A.C.
9. Recheck Steps

Refer to Installer Checklist on the back cover of this manual and make sure that dryer is installed correctly.

Check Heat Source

Electric Dryers

1. Close the loading door and start the dryer in a heat setting (refer to the operation instructions).
2. After the dryer has operated for three minutes, the exhaust air or exhaust pipe should be warm.

Gas Dryers

IMPORTANT: This operation is to be conducted by qualified personnel only.

1. To view the burner flame, remove the lower front panel of the dryer.

2. 2. Close the loading door and start the dryer in a heat setting (refer to the operation instructions). The dryer will start, the igniter will glow red and the main burner will ignite.

   • IMPORTANT: If all air is not purged out of gas line, gas igniter may go off before gas is ignited. If this happens, after approximately two minutes igniter
     will again attempt gas ignition.

   • IMPORTANT: If igniter does not light, make sure gas is turned on.

3. After the dryer has operated for approximately five minutes, observe burner flame through lower front panel.

4. Adjust the air shutter to obtain a soft, uniform blue flame. (A lazy, yellow-tipped flame indicates lack of air. A harsh, roaring, very blue flame indicates too much air.) Adjust the air shutter as follows:

   • a. Loosen the air shutter lockscrew.
   • b. Turn the air shutter to the left to get a luminous yellowtipped flame, then turn it back slowly to the right to obtain
   • a steady, soft blue flame.
   • c. After the air shutter is adjusted for proper flame, tighten the air shutter lockscrew securely.

5. Reinstall the lower front panel.

   • WARNING
   • To reduce the risk of serious injury or death, lower front panel must be in place during normal operation.

6. After the dryer has operated for approximately three minutes, exhaust air or exhaust pipe should be warm.

Figure 29

1. Air Shutter Lockscrew
2. Air Shutter
3. 1/8 in. [3.1 mm] Pipe Plug (For checking manifold pressure)

Installer Checklist

Fast Track for Installing the Dryer

• Refer to the manual for more detailed information
• © Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Part No. D518518ENR2

Original Instructions

• Keep These Instructions for Future Reference.
• CAUTION: Read the instructions before using the machine.
• (If this machine changes ownership, this manual must accompany machine.)

References

• FreeRTOS - Market leading RTOS (Real Time Operating System) for embedded systems with Internet of Things extensions

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>