REELCRAFT TH5000 Series Spring Driven Hose Reels Instruction Manual
- June 9, 2024
- REELCRAFT
Table of Contents
REELCRAFT TH5000 Series Spring Driven Hose Reels
Operating Instructions
Series TH5000 Spring Driven Hose Reels
Medium Pressure Model Numbers: TH5400 OMP
Dimensions
| A| 14 1/2”
---|---|---
B| 13 1/2”
C| 9 3/4”
D| 2 1/2”
E| 6”
SAFETY
- Do not use reel at higher pressures or temperatures than listed on the back of this bulletin.
- Remove all spring tension before beginning dissassembly process.
INSTALLATION:
A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible misalignment and binding.
MOUNTING:
The hose reel is equipped with a universal mounting bracket so that it can
be mounted on the floor, wall or ceiling; whichever place is convenient. The
hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm
bracket so the hose comes off the
reel at the desired position and replace the screws. NOTE: For proper
installation in wall mount applications, ensure reel is mounted with inlet on
the right as you are facing the reel. Failing to do so could cause latching
issues. Hose reel spring and bearings are factory lubricated and require no
further lubrication.
LUBRICATION:
REPLACING HOSE:
- Wind spool flange clockwise-facing swivel-until spring is tight.
- Back off three turns and latch.
- Insert hose through roller guide.
- Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS:
To adjust spring tension, add or remove wraps of hose from the spool, one
wrap at a time until desired tension is obtained.
REPAIRS:
Extensive repairs should be performed only by an authorized serviceman or
factory to avoid damage which may void your warranty. Remove all spring
tension before beginning disassembly process.
Form# 1150-1003
Rev: 2/2023
Reelcraft Industries, Inc.
- 2842 E Business Hwy 30, Columbia City, IN 46725 Ph: 800-444-3134 / 260-248-8188
- Fax: 800-444-4587 / 260-248-2605 Customer Service: 855-634-9109
- reelcraft@reelcraft.com
- www.reelcraft.com
Series TH5000 Spring Driven Hose Reels
Item| Part| Req.| Description| Item| Part|
Req.| Description
---|---|---|---|---|---|---|---
1| S600996-1| 1| Swivel Assembly| 17| S500103| 1| Spring Case & Hub Assembly
2| 300031| 2| 1” Snap Ring| 18| S82-15| 1| 10-32 x 3/8” Nyloc Nut
3| 300034| 2| Spacing Washer| 19| S400021| 1| Latch Bumper
4| S295-102| 3| Self Tap Screw Plastite| 20| S32-136| 1| 10-24 x 3/8” Screw
5| 260022| 1| Reel Sheave| 21| S400012| 1| Latch Bushing
6| 500006| 1| Reel Sheave Disk| 22| S400018| 1| Latch Spring
7| S500019| 1| Latch Cam| 23| 300001| 5| 10-32 x 3/8” Mach. Screw
8| S260648| 1| Spring Arbor| 24| 400020| 1| O’Ring
9| 300002| 2| 10-32 x 1/2” Machine Screw| 25| S400109| 1| Latch Plate Assembly
10| S500107| 1| Guide Arm & Roller Assembly| 26| 300035| 1| 10-32 x 1” Machine
Screw
12| 500101| 1| Base Assembly| 27| 1-117440| 1| U-Bolt Hose Clamp
13| S300011| 7| 10-32 Hex Nut| 28| 300070| 2| 1/4-20 Nyloc Nut
14| S507287| 1| Drive Spring Assembly| 29| 300039| 2| Washer
15| S261360| 1| Spring Case Stud| 30| 602306| 1| Main Shaft
16| 300006| 1| 3/8-16 x 1/2” Set Screw| | | |