OLIGHT Olantern LED Lantern Flashlight User Manual
- June 9, 2024
- OLIGHT
Table of Contents
OLIGHT Olantern LED Lantern Flashlight
Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!
IN THE BOX
FEATURES
- Featuring two interchangeable LED modules, the Olantern allows you to switch between standard white light or an ambient ickering ame.
- The high-performance LED combined with transparent cover ensures an even,steady 360° light distribution.
- Powered by four 3.7V 1900mAh lithium-ion batteries, it is rechargeable via MCC3 and runs up to 80 hours.
- The reliable hanging hook and stable base make carrying,storing and decorating super handy.
- The battery indicator around the button is motion-sensitive, fading on and o to help locate your lantern in the darkness.
SPECIFICATIONS
All above specifications are test results based on ANSI/NEMA FL1-2009 Standard
USB MAGNETIC CHARGING CABLE — MCC3
- Charging cable: USB type A – magnetic charging connector, length: 1.2m
- Input: USB A – Type DC 5V 2A
- Charging pattern: CC&CV
- Maximum charging current: 1.5A
- Voltage of fully charged battery: 4.2V±0.05V
- Charge indication
- Red: charging
- Green: full (over 95%) or disconnect Olantern ed with
- Time to fully charge: 7 hours (For reference only. When the USB power source is insucient to provide 8W power capacity, the charging time will be longer)
PRODUCT OVERVIEW
BATTERY LEVEL INDICATOR
CHARGING
- Before rst use please fully charge the product.
- Connect the magnetic USB end of the charging cable (MCC3) to an external USB power source, then attach the other end of the magnetic charging cable to the charging port (best charging eciency with more than USB 8powe W r source). The red indicator means charging, green indicator means charging completed (battery power ＞95%).
- Only charge with standard MCC3, not compatible with other MCC.
LED MODULE REPLACEMENT
Turn o the Olantern. Unscrew the cover as guided by the “OPEN” mark on the upper cap and remove it. Turn around the LED module anticlockwise and remove it from the base. Fetch another module and screw it onto the base. Reinstall the cover. If the LED module is not put in place, the indicator around the button will have no response and the product won’ t work when you turn on the Olantern.
NOTICE
The Olantern battery indicator is motion-sensitive. The indicator will fade on
and o in green, yellow, or red to indicate a high, medium, or low battery
level when you move the Olantern. After seven seconds with no motion, the
indicator will turn off.
DANGER
- DO NOT throw the light directly into human eyes, which may cause temporary blindness or permanent damage to the eyes.
- DO NOT cover the Olantern that is on. The generated heat can cause burning or even unpredictable disasters.
- Keep it out of reach of children.
WARNING
DO NOT immerse the Olantern in water.
HOW TO OPERATE
- ON/OFF: Single click the button to turn the Olantern ON/OFF. The Olantern would return to the previously memorized setting when it is on.
- CHANGE BRIGHTNESS LEVEL: When the Olantern is on with the White Light LED Module, press and hold the button and the Olantern would start from the present brightness level, automatically cycle through low, medium, and high setting. As for the Flaming LED Module, the brightness is xed and cannot be changed.
- LOCKOUT/UNLOCK: When the Olantern is o, press and hold the button, it will enter the Lockout mode after staying in the low setting for a while. Under the lockout mode, when single click the button, the red indicator around the button will be on to signal that the Olantern is in lockout mode. To unlock it, keep holding the button until the Low mode is on again.
References
- Olight | Illuminate Your World.
- Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight