LG SBWAC97 Bluetooth Combo DBDC Module User Manual

June 9, 2024
LG

LG SBWAC97 Bluetooth Combo DBDC Module

The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek.

Features

  • ETWCFMBC03 is the small size and low power module for IEEE 802.11ac wireless
  • LAN & BT5.0 + HS. ETWCFMBC03 is based on Mediatek MT7668AUN solution.
    • IEEE 802.11 a/b/g/n/ac Dual Band Dual Concurrent (DBDC)
    • Bluetooth 5.0 + HS , BLE
    • Size : 48.0 x 30.0 x 7.7mm
    • Two stream spatial multiplexing up to 300Mbps(802.11n) / 867Mbps(802.11ac)
    • Use on-chip OTP (One-Time Programmable)
    • Host Interface : USB2.0 (WLAN & BT)
    • This model is using the common USB2.0 to control WLAN and BT
    • Security : WAPI, WEP, WPA, WPA2, WMM, AES, TKIP, CKP
    • Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB

Block Diagram

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-2

Absolute Maximum Ratings

Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device.

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-9

Other conditions

  1. Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture.
  2. Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%.
  3. Assemble the modules within 6 months. Check the soldering ability in case of 6 months over.

Operating Conditions

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-10

Standard Test Conditions

The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance.

Ambient condition

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-11

Power supply voltages

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-12

Current consumption

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-13

Note 1 : This figure is the RMS(root mean square) Value.

ESD Information

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-14

Pin Description

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-3
LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-15

Mechanical Characteristics

Outline view

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-16

Appearance structure

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-17

Outline Drawing

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-4 LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-5

Tune-up Power

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-6

Bottom Connector FFC Cable Type

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-7

Top Connector FFC Cable Type

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-8

FCC Statement

  • FCC Part 15.19 Statements:
    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • FCC Part 15.105 statement (Class B)
    This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.
  • FCC Part 15.21 statement
    Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

  • Responsible Party Information
    Supplier’s Declaration of Conformity47 CFR §2.1077 Compliance Information

  • Responsible Party –U.S. Contact InformationLG Electronics USA1000 Sylvan
    Avenue Englewood Cliffs New Jersey, United States, 07632Telephone number or internet contact information

Regulatory notice to host manufacturer according to KDB 996369 D03 OEM Manual v01 >
List of applicable FCC rules

  • This module has been granted modular approval as below listed FCC rule parts.
  • FCC Rule parts 15C(15.247)

Summarize the specific operational use conditions

The OEM integrator should use equivalent antennas which is the same type and equal or less gain then an antenna listed in 2.7 in this instruction manual.

RF exposure considerations

  • The module has been certified for integration into products only by OEM integrators under the following condition:
  • The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.
  • The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi transmitter product procedures.

Mobile use

  • As long as the three conditions above are met, further transmitter testing will not be required.
  • OEM integrators should provide the minimum separation distance to end users in their end-product manuals.

Antennas list

  • This module is certified with the following integrated antenna.
    • Type: Metal antenna (Internal Antenna)
    • Max. peak Antenna gain

LG-SBWAC97-Bluetooth-Combo-DBDC-Module-fig-18

  • Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.

Label and compliance information

  • End Product Labeling
    The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: “Contains FCC ID: BEJLGSBWAC97” “Contains IC: 2703H- LGSBWAC97”

  • Information on test modes and additional testing requirements
    OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.).

  • Additional testing, Part 15 Subpart B disclaimer
    The final host product also requires Part 15 subpart B compliance testing with the modular transmitter installed to be properly authorized for operation as a Part 15 digital device.

ISED

RSS-GEN, Sec. 7.1.3–(licence-exempt radio apparatus)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. this device may not cause interference, and
  2. this device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure

  • The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual.
  • This device may not be installed or used in conjunction with any other antenna or transmitter.
    Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals