FEASYCOM FSC-BP301W Serial WIFI Adapter Instruction Manual
- June 9, 2024
- FEASYCOM
Table of Contents
FSC-BP301W serial WIFI adapter
instruction manual
FSC-BP301W Serial WIFI Adapter
1、SMA antenna connector
2、Power off/slave mode/master mode
3、Green communication indicator
4、Type-C charging interface
5、Blue status indicator| 6、Red charging indicator
7、Tighten the screws
8、Restore factory settings button
9、DB9 female connector
10、SMA antenna
---|---
Introduction
FSC-BP301W is an RS232 serial port WIFI adapter with built-in lithium battery and charging circuit, which can be used in situations without external power supply. FSC-BP301W has abundant AT command, complete function, efficient and safe communication and strong anti-interference ability. The main function is to provide cloud services for devices with RS232 interface.
mode
WAN function is to provide customers who need to go to the cloud. Any device
with standard RS232 serial port can upload data to the cloud service by
connecting FSC-BP301W.
BP301W can upload data to FeasyCloud at the data uplink end (connecting RS232
device), and BP301W or other interface devices of FeasyCloud can be selected
at the downlink end.
In the same way, BP301W can also upload data to FeasyCloud at the data
downstream end (connecting to RS232 device), and BP301W or other interface
devices of FeasyCloud can be selected at the upstream end.
Specifications
3.1 Technical parameters
WIFI specification：802.11 a/b/g/n 1×1, 2.4GHz & 5GHz
Frequency：2.400 ~ 2.484GHz; 5.18 ~ 5.825GHZ.
Transmission rate：54Mbps in 802.11g , 150Mbps in 802.11n, 54Mbps in 802.11a
TX power：(2.4GHZ) 17.5 dBm(11 b),15.5 dBm(11 g), 13.5 dBm(11 n)
(5GHZ): 16dBm(11 a)
Working current：450mA (MAX)
Battery capacity：500mAh
Dimension：121 X 34 X 15.8mm
Product weight：62g
3.2Factory parameters
The default parameters of FSC-BP301W when leaving the factory are as follows.
Some parameters can be modified by sending AT commands to the adapter. For
details, please refer to the AT command manual.
Baud rate：115200bps
Verification：None
Data bits：8
Stop bit：1
WIFI name：FSC-BP301W
Pairing code：0000
Hardware structure
Refer to the hardware structure diagram on the first page.
4.1 Switch
- Power on (OFF): Switch to DB9 female head.
- Slave mode (S): Turn the switch to the middle.
- Master mode (M): Switch to antenna head and connect the slave device by AT command.
4.2 Power supply
Powered by built-in lithium battery: Switch to slave or master mode to turn on
the adapter .Turn it to the side of the OFF icon to cut off the battery power
supply and turn off the adapter.
To charge the built-in lithium battery: Use the Type-C cable to insert the
charging port, and connect the other end to the computer USB, the red
indicator light will light up; when the charging is complete, the red light
will go off.
4.3 Indicator
- Red charging indicator: Light up when charging, goes out after charging.
- Blue status indicator: On for 200ms, off for 1s under slave mode; flashes quickly for 200ms and off for 200ms under master mode.
4.4 Restore factory
If forget baud rate, please restore the factory setting by pressing the reset
button. The factory setting is fixed at 115200bps. The operation is to press
and hold the reset button. At this time, the blue light is always on. If reset
is successful, the light flashes 2 times.
Setup and use
5.1 AT command settings
To set up FSC-BP301W through AT commands, it usually needs to be operated
on a computer. So first, you need to establish a serial port debugging
environment on your computer. Serial debugging requires the computer to have a
free serial port, and it also needs to run the serial debugging software on
the computer.
5.1.1 Serial debugging hardware preparation
Connect FSC-BP301W to the DB9 male socket of the computer. If there is no
RS232 interface on the computer, you need to purchase a USB-to-serial adapter
or a USB-to-serial cable to add a serial port for the computer.
5.1.2 Preparation of serial port debugging software
A variety of serial port debugging software can be downloaded online, users
can choose according to their own preferences. It is recommended to use
Feasycom serial port assistant V1.2 debugging tool, users can contact Feasycom
technical support. Carriage return line feed characters must be added to the
end of FSC-BP301W AT commands, by checking the option of “Send New Line” if
use Feasycom serial port tool. The operation is as follows
5.1.3 Send AT command
Start the serial port tools, select the physical serial port number of FSC-
BP301W connect with the computer, set the baud rate and other parameters of
the serial port to keep it consistent with the WIFI serial port parameters of
the FSC-BP301W (default 115200, N, 8, 1), and then “open serial port”. Send
test command AT, if it returns OK, it means that the AT command debugging
environment is established, and you can send other AT commands to set FSC-
BP301W.
For detailed instructions.Please refer to the <FSC-BW236 Programming User
Guide V3.1 (Universal).pdf> document.
Product packing list
- One FSC-BP301W serial WIFI adapter
- One SMA antenna
- An instruction manual
FAQ
Question: I use the Feasycom serial port tools to debug FSC-BP301W, why couldn’t it return OK after sending the AT test command?
– Answer: It is probably that the serial port parameter selection is incorrect, please check the parameters of serial port number, baud rate, data bit, stop bit, check method, etc. The parameter selection of computer serial port should be consistent with the parameters of FSC-BP301W serial port WIFI adapter.It is also possible that the HEX transmission or display is selected by mistake, or the serial port is not opened.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>