Milwaukee 48-22-8485 PACKOUT Wall and Floor Mounting Plate User Manual
- June 9, 2024
- Milwaukee
Table of Contents
48-22-8485 PACKOUT Wall and Floor Mounting Plate
User Manual
48-22-8485 PACKOUT Wall and Floor Mounting Plate
The PACKOUT™ Mounting Plate can be installed several different ways for
vehicle and shop use.
WARNING
Read all safety warnings, instructions, illustrations and specifications
provided. Failure to follow all instructions listed below may result in
serious injury and/or property damage. Save all warnings and instructions for
future reference.
- Always use common sense and be cautious when using and installing mounting plate. It is not possible to anticipate every situation that could result in a dangerous outcome. Do not use this product if you do not understand these instructions or you feel the work is beyond your capability; contact Milwaukee Tool or a trained professional for additional information or training.
- To reduce the risk of injury when used in a vehicle, install according to vehicle manufacturer’s instructions. A bulkhead must be properly installed to provide protection between the PACKOUT™ and the occupant.
- Do not transport AC-equipped products vertically on a vehicle wall. If product is damaged during transport, it could cause an electrical hazard when plugged in. Always inspect AC products before connecting to a power source.
- Use only fasteners recommended in the installation instructions. Do not use other fasteners, such as self-tapping or drywall screws.
- Inspect the mounting plate and all fasteners periodically and replace immediately if cracked, worn, or damaged. Do not attempt to fix or mend damaged mounting plates or fasteners.
- If a loaded mounting plate has received an impact or is involved in an accident, MILWAUKEE recommends you replace the mounting plate and mounting fasteners before future use.
- Ensure PACKOUT™ is secured before vehicle is in motion. Do not use, adjust or modify PACKOUT™ while vehicle is in motion.
- Use cam-lock style straps for in-vehicle applications. Ratchet straps can result in over tightening and product damage. (Integrated only exist in 48-22-8485).
- When wall mounting in a vehicle, only use with PACKOUT™ productsthat can be locked directly to the mounting plate (e.g., do not use with a crate with back cleats). Hook-only products can fall when jarred or bumped.
- Do not exceed maximum loading capacity (see Specifications). Overloading can cause mounting plate to come loose and break free, resulting in injury and product damage.
Cat. No.| In-Vehicle
Max
(On Wall)| In-Vehicle
Max
(On Floor)| In-Shop
Max
(On Wall)| In-Shop
Max
(On Floor)
---|---|---|---|---
48-22-8485| Weight:
50 lb
(22.7 kg)
Stack
Height:
13″
(330 mm)| Weight:
100 lb
(45 kg)
Stack
Height:
26″
(660 mm)| Weight:
100 lb
(45 kg)
Stack
Height:
13″
(330 mm)| Weight:
250 lb
(113 kg)
Stack
Height:
26″
(660 mm)
48-22-8486| Weight:
251b
(11 kg)
Stack
Height:
13″
(330 mm)| Weight:
501b
(22.7 kg)
Stack
Height:
16.5″
(419 mm)| Weight:
501b
(22.7 kg)
Stack
Height:
13″
(330 mm)| Weight:
1251b
(56.7 kg)
Stack
Height:
26″
(660 mm)
48-22-8487| Weight:
75 lb
(34 kg)
Stack
Height:
13″
(330 mm)| Weight:
150 lb
(68 kg)
Stack
Height:
26″
(660 mm)| Weight:
150 lb
(68 kg)
Stack
Height:
13″
(330 mm)| Weight:
3751b
(170 kg)
Stack
Height:
26″
(660 mm)
IN-VEHICLE MOUNTING INSTRUCTIONS
WARNING
To reduce the risk of injury when used in a vehicle, install according to
vehicle manufacturer’s instructions. A bulk- head must be properly installed
to provide protection between the PACKOUT™ and the occupant.
Use cam-lock style straps for in-vehicle applications. Ratchet straps can
result in over tightening and product damage.
Only use with PACKOUT™ products that can be locked directly to the mounting
plate (e.g., do not use with a crate with back cleats). Hook-only products can
fall when jarred or bumped. Orientate the mounting plate as indicated,
taking into account the direction of travel and, if necessary, wall
orientation.
Mounting plate must be installed on flat, smooth walls or floors. Uneven
surfaces could cause the mounting plate to warp, resulting in possible
problems when installing PACKOUT™ products.
Use the below recommended fasteners in all mounting holes.
If installing into Wood:
-
Install onto dimensional lumber (2×4 or larger) or 3/4″ thick plywood
-
Use Ø 1/4″ x 1-1/4″ lag screws
If installing into Sheet Metal: -
Install onto minimum 22 gauge sheet metal.
-
Use Ø 1/4″-20 Threaded Inserts such as screw-to-install rivet nuts (jack nuts)
-
Use medium strength (blue) liquid threadlocker
IN-SHOP MOUNTING INSTRUCTIONS
Position the mounting plate as indicated, taking into account the wall
orientation.
Mounting plate must be installed on a flat, even surface. An uneven surface
could cause the mounting plate to warp, resulting in possible problems when
installing PACKOUT™ products.
For maximum support, attach to 16″ center studs whenever possible. At
minimum, use the recommended fasteners in all mounting holes circled BOLD in
the diagrams below.
If installing into Wood:
-
Install onto dimensional lumber (2×4 or larger) or 3/4″ thick plywood
-
Use Ø 1/4″ x 1-1/4″ lag screws
If installing into Concrete or Drywall: -
Use suitable anchors rated to at least 50 lb. per anchor
A local Milwaukee authorized service station or factory Service Center can
help with the purchase of the correct Service Assembly.
To locate the facility nearest you call 1.800.SAWDUST [1.800.729.3878] or
visit www.milwaukeetool.com – a location can
be found under the ‘Parts & Service’ – ‘Service Center Search’ Icon.
If you have questions, please call 1.800.SAWDUST [1.800.729.3878] MILWAUKEE
TOOL • www.milwaukeetool.com
13135 West Lisbon Road • Brookfield, Wisconsin USA 53005
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>