VTS5000D Control and Modbus Communication Instructions

June 9, 2024
VTS

VTS5000D Control and Modbus Communication

VTS5000D Control and Modbus Communication Instructions
product

Description

Index Number Description Sanyu Customized Model
1-2-1208-5024 FC 0,75kW 3PH 3~400V VFD VTS5000D-0R7G-4
1-2-1208-5025 FC 1,5kW 3PH 3~400V VFD VTS5000D-1R5G-4
1-2-1208-5026 FC 2,2kW 3PH 3~400V VFD VTS5000D-2R2G-4
1-2-1208-5033 0,75kW 1PH 1~230V VFD_S2 VTS5000D-0R7G-S2
1-2-1208-5034 1,5kW 1PH 1~230V VFD_S2 VTS5000D-1R5G-S2
1-2-1208-5035 2,2kW 1PH 1~230V VFD_S2 VTS5000D-2R2G-S2

THE FOLLOWING MANUAL ASSUMES GOOD KNOWLEDGE OF TECHNICAL DOCUMENTATION INCLUDED WITH THE AIR HANDLING UNIT (AHU).  THIS MANUAL CONSIDERS ONLY THE CONTROL AND COMMUNICATION CIRCUITS. THE INSTALLATION OF THE FREQUENCY CONVERTER AND INSTALLATION OF MAINS AND MOTOR CABLES SHOULD BE DONE ACCORDING TO THE VTS5000D MANUAL.

 FOR ALL CONFIGURATIONS SET THE COMMON PARAMETER LIST

Parameter Code Value Comments
Maximum frequency P105 100
Acceleration Time 1 P107 45 recommended 45 sec.
Deceleration Time P108 45 recommended 45 sec.
Rated motor voltage P209 380 0-500V
Rated motor current P210 * Scale: 0.1 A
Motor rated speed P212 *
Number of motor poles P213 *
Rated motor slip P214 ** 0.1HZ
Rated motor frequency P215 50

Motor overload protection selection

| P816| 1|

0: Prohibit
1: Permit

CONFIGURATIONS WITHOUT VTS CONTROLS

Local control using integrated control panel

Set additional parameters:

Parameter Code Value Comments
Main frequency source X selection P101 3 Local keypad potentiometer setting

mode
Start signal selection| F102| 0| 0: Operation panel (FWD/REV/STOP)
1: I/O terminal
2:Communication(RS485)
Maximum frequency| P105| 100|
Minimum frequency| P106| 20|
Switch AI jumper to I to choose analog current input
AI minimum voltage input| P300| 0V| 0.00V~P301
AI maximum voltage input| P301| 10V|

Use the RUN and STOP/RST buttons to control the drive Use buttons to set frequency

 Remote control with three speeds

Set additional parameters:

Parameter Code Value Comments
Main frequency source X selection P101 6 Multi-speed
Start signal selection F102 1 0: Operation panel (FWD/REV/STOP)

1: I/O terminal
2:Communication(RS485)
SET multi function terminal REV| P316| 9| Multi -speed 1
SET multi   function   terminal S1| P317| 10| Multi -speed 2
SET multi   function terminal S2| P318| 11| Multi -speed 3
Multi speed 1 (speed I)| P503| | 20 – 100Hz
Multi speed 2 (speed II)| P504|
| 20 – 100Hz
Multi speed 3 (speed III)| P505| *| 20 – 100Hz
RA,RC| P325| 3| 3:Alarm (stop)

Wire the I/O terminal of the VTS5000D inverter according to the Figure 1VTS5000D Control and Modbus Communication Instructions
01Use FWD/REV/S1/S2 inputs to set desired drive function (1=on,0=off)

0000 = STOP|
---|---
1100 = START, 1ST SPEED| Value is P503
1110 = START, 2ND SPEED| Value is P503+P504
1111 = START, 3RD SPEED| Value is P503+P504+P505

 EXHAUST UNIT WITH VTS CONTROL SYSTEM

Parameter Code Value Comments
Main frequency source X selection P101 6 Multi-speed
Start signal selection F102 1 0: Operation panel (FWD/REV/STOP)

1: I/O terminal
2:Communication(RS485)
SET multi function terminal REV| P316| 9| Multi -speed 1
SET multi   function   terminal S1| P317| 10| Multi -speed 2
SET multi   function terminal S2| P318| 11| Multi -speed 3
Multi speed 1 (speed I)| P503| | 20 – 100Hz
Multi speed 2 (speed II)| P504|
| 20 – 100Hz
Multi speed 3 (speed III)| P505| *| 20 – 100Hz
RA,RC| P325| 3| 3:Alarm (stop)

Wire the I/O terminal and the terminal X3 of the control box CG according to the Figure 2a

VTS5000D Control and Modbus Communication Instructions
02Use FWD/REV/S1/S2 inputs to set desired drive function (1=on,0=off)

0000 = STOP|
---|---
1100 = START, 1ST SPEED| Value is P503
1110 = START, 2ND SPEED| Value is P503+P504
1111 = START, 3RD SPEED| Value is P503+P504+P505

NOTE! If the AHU is equipped with more than 1 fan, follow Figure 2b for proper cabling.

VTS5000D Control and Modbus Communication Instructions
03 AHU WITH VTS CONTROLS TYPE: VS … CG ACX36 EVO … or VS … CG uPC …
Set additional parameters

Parameter Code Value Comments
Main frequency source X selection P101 5 5: RS485 communication frequency

setting
Start signal selection| F102| 2| 2:Communication(RS485)
---|---|---|---
Converter’s address in Modbus Network| P702| 2| Air-supply fan
3| Air-exhaust fan
5| Air-supply fan No.2 / redundant
7| Air-supply fan No.3
9| Air-supply fan No.4
6| Air-exhaust fan No.2/ redundant
8| Air-exhaust fan No.3
10| Air-exhaust fan No.4
Action of RS485 communication error| P703| 2| 0: No warning
1: Warning, display Co 2: Display Co and stop

Communication parameters as below: Modbus RS-485, 9600 8N1,
Wire the communication terminal of the VTS5000D inverter according to the VTS5000D Control and Modbus Communication Instructions
04CAUTION: It is recommended to apply an automatic procedure for the converters’ configuration, which is available in advanced options of the HMI Advanced panel.
NOTE: To restore VTS5000D to default settings set P117 = 8 and switch off the power supply.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals