FS KVM Series LCD KVM Switches User Guide

: June 9, 2024
: FS

Table of Contents

FS KVM Series LCD KVM Switches
Introduction
Accessories
Hardware Overview
- Front Panel Buttons
Installation Requirements
Opening &Closing the Console
Local Control
Online Resources
Product Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FS KVM Series LCD KVM Switches

Introduction

Thank you for choosing KVM Series LCD Switches. This guide is designed to familiarize you with the layout of the KVM switches and describes how to deploy them in your network.

Accessories

NOTE: The number of KVM cables for KVM-080119 is 8, and that of KVM-016119 is 16.

Hardware Overview

Front Panel Buttons

KVM-080119

KVM-160119

button	component	function
1-8/16	Port Selection	Switch freely from port 1 to port 8/16.

Reset

|

Press [1] and [2] at the same time to reset the KVM.

2
7|

Bank

| Press [7] and [Bl at the same time to switch to the next stage level.
8

LED OSD Control Buttons
KVM-080119/KVM-160119

button	function

AUTO/EXIT

| Press this button to exit the current menu and return to the previous menu or exit the LED OSD, or enter the automatic configuration.
SL-/SL+| Press this button to move your menu to make the corresponding adjustment.
MENU SELECT| Press this button to invoke the menu function and open the main menu.

LED OSD Control LED
KVM-080119/KVM-160119

| |
---|---|---

Power

| Solid Green| KVM is powered on.
Solid Red| Power off or access non-standard VESA signal.
Flashing Green| Energy saving mode or no signal.

Front Panel LEDs
KVM-080119

KVM-160119

| |
---|---|---

Online LED

|

Green

| KVM has been connected to its corresponding computer and powered on.
Selected LED| Red| The computer attached to its corresponding port is up and running.
Station ID| | Display the current port.

Back Panel Ports
KVM-080119

KVM-160119

|
---|---
Power Input (AC)| A power input port for the AC power cord
Power Switch| Turn on/off the power
Ground Connecting Screw| For grounding the KVM switch
CONSOLE| Connect to a monitor, USB or PS/2 keyboard and mouse
Daisy-chain in| Connect to a daisy chaining cable
PCl~8/16| Connect to a mouse, keyboard, and VGA port

Installation Requirements

Site Environment

Do not operate it in an area that exceeds an ambient temperature of 50°C or nearby heat SOurces.
The installation site should be well-ventilated.
Be sure that the KVM switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.

Rack Mounting

Secure the KVM switch to the rack with the screws and nuts.
Slide the rack-mount kit into the switch’s side mounting brackets from back to front, then screw the rack-mount kit to the rack.

Grounding the KVM Switch

Connect one end of the grounding wire toa proper earth ground, such as the rack where the KVM switch is mounted.
Secure the grounding lug to the grounding point on the back panel with the washers and screws.

Connecting the Power

Plug the provided AC power cord into the power port on the back panel.
Connect the other end of the power cord to an AC power source.
Open the power switch on the back panel.

WARNING: Do not install power cables when the power switch is on.
NOTE: DC power cord is not included in the accessories.

Connecting to the Console Ports

Connect the monito, USB or PS/2 keyboard and mouse to the console ports on the KVM switch (optional).

Connecting to the Cascade Port

Plug the yellow port of a daisy chaining cable into the yellow “Daisy-chain in” DB 15 port on the kVM switch.
Plug the other blue port of the daisy chaining cable into the blue “CONSOLE” DB 15 port on the KVM switch.

Opening &Closing the Console

Opening the Console

Unlock the release catch.
NOTE: The release catch is locked horizontally, and it can’t bear any load.
Pull the LED panel all the way out until it clicks into place.
Open the LED panel to display the LED screen; the LED panel can be rotated up to 108.

Closing the Console

Close the LED display panel and the power automatically turns off.
Push the LED panel all the way in until it automatically locks up.

Local Control

Step 1: KVM-080119 and KVM-160119 can be set with their own keyboard and LED screen, as well as the external keyboard, mouse and monitor connected to the console ports of the KVM switch.
Step 2: Unlock the release catch, pull the LED panel and open the screen.
Step 3: Two “beeps” are heard after turning on the power switch. The ONLINE LED lights on the front panel keep green-flashing.
Step 4: Enter the default username and password, admin/admin.

Online Resources

Download
https://www.fs.com/download.html
Help Center
https://www.fs.com/service/help_center.html
Contact Us
https://www.fs.com/contact_us.html

Product Warranty

Warranty: KVM Switches enjoy a 2-year limited warranty against defects in materials or workmanship. For more details about the warranty, please checkat
https://www.fs.com/policies/warranty.html
Return: If you want to return the item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html