DRAGONFLY Ambient Light Reflecting Thin-Bezel Fixed Projection Screens Instruction Manual
- June 9, 2024
- DragonFly
Table of Contents
Ambient Light Reflecting Thin-Bezel Fixed Projection Screens
Instruction Manual
Ambient Light Reflecting Thin-Bezel Fixed Projection Screens
INSTALLATION MANUAL
Ambient Light Reflecting Thin-Bezel Fixed Projection Screens
IMPORTANT: BEFORE YOU BEGIN
- To avoid staining or scratching the screen, wear the included gloves during installation. Wash your hands and clean the work area before starting.
- Do not use knives or sharp objects to open the packing boxes.
- To avoid a serious fire hazard, DO NOT install the screen over an electrical outlet or switch.
Step 1. Unpack the Screen
Lay out all parts on a clean, flat surface. To prevent damage, do not unpack
the screen material at this time.
NOTE: Quantities below may be greater than needed for assembly.
Package Contents
Step 2. Prepare Frame Sections for Assembly
A. Retention springs are pre-assembled. Please confirm based on quantity noted
on frame label for the short and long frame sections.
i. The hook on the spring must be nearest the inside frame edge.
B. Sliding nuts are pre-installed into frames, 16 total. Sliding nuts are used
to install the thin bezel caps, center stabilizing bar, and wall brackets.
Please ensure all 16 sliding nuts are on the frames prior to installing and
tightening the corner brackets.
C. Install the corner brackets to the top and bottom slots of the short frame
sections.
i. The small bracket goes in the bottom slot, and the large one goes in the
top slot.
Step 3. Assemble
the Frame
A. Slide the short frame sections into the long frame sections.
B. Insert the 8 frame corner screws into all 4 corners of the frame and
loosely tighten to hold the frame together.
C. Hand-tighten all four screws, ensure the corners are square, then tighten
the screws completely.
D. Lift up and set aside to prepare screen material for assembly.
Step 4. Prepare the Screen Material
A. Lay the plastic sheet out on the work surface, and clean the plastic
surface and work area to avoid staining the screen material.
B. Put on the supplied gloves before handling the screen material.
C. Roll the ALR material out onto the plastic, then lay the frame down onto
the material, ensuring the corners of the frame and ALR fabric are properly
aligned as shown.
Step 5. Attach the Screen Material to the Frame
A. Align the springs to the holes in the ALR fabric,
B. Using the spring tools, attach the spring in the corners first, then the
centers of each side as shown below.
Once the corners and center springs are connected, work around the screen and
attach the remaining springs, making sure to keep the spring tension balanced.
Step 6. Install
Brackets and Frame Bezels
A. Install the center support bar to the frame using the sliding nuts
installed in the centers of the long sides of the frame.
B. Turn the frame over and slide the long frame bezels onto the long sides of
the frame, and the short sides onto the short sides of the frame.
i. Slots on back of
the thin bezel will line up for a tight fit.
C. Install the bezel brackets to secure the frame bezels to the frame.
i. Line up the
brackets and sliding nuts for an easier corner fit.
Installation Tips
Take care to pull material evenly before installing the bezels.
If waves/wrinkles are present, it may be necessary to remove the bezel and
pull the material tightly before reattaching the bezel.
Step 7. Attach and Install the Mounting Brackets
A. Screw the
retaining plates into the sliding nuts.
B. Loosely secure the two mounting brackets to the sliding nuts in the top
frame using the M5 x6mm screws. The brackets should just be able to slide left
and right.
C. Loosely secure the circular metal half of the magnets to the lower frame,
do not tighten the screws completely, the brackets should just be able to
slide left and right.
Step 8. Hang the Screen
A. Measure the overall Length and height of the screen frame.
B. For Drywall: Drill
4 holes in the wall at the desired height.
The distance of the horizontal holes should be about 2/3 the width of the
frame, and the vertical distance of the holes should be the height of the
frame minus 4⅛” (105 mm).
C. For Concrete: Drive the concrete anchors into the holes drilled
in Step B. Drive 2 M5x40mm Screws into the concrete anchors leaving 5mm to
hang the screen. Install the lower 2 magnet pieces using 2 M5x40mm screws.
Hang the screen on the upper brackets and attach the lower part of the frame
to the wall with the magnets.
Care and Cleaning
Clean the screen with a soft microfiber cloth only. DO NOT use soap, water,
harsh detergents, chemicals, distilled spirits or petroleumbased chemicals to
clean the screen. Doing so may result in severe damage to the screen or the
frame coating.
Use a household
vacuum cleaner with a brush or furniture cleaning attachment to clean the felt
frame material. Avoid using excessive amounts of water on the felt.
Dimensions (in Inches)
| A | B | C | D | E | F | G |
|---|---|---|---|---|---|---|
| 92″ | 45.1 | 80.2 | 45.7 | 80.7 | 2.7 | 1.3 |
| 100″ | 49 | 87.2 | 49.6 | 87.7 | 2.7 | 1.3 |
| 110″ | 53.9 | 95.9 | 54.5 | 96.4 | 2.7 | 1.3 |
| 120″ | 57.38 | 102.83 | 58.38 | 103.38 | 2.7 | 1.3 |
Warranty
Find details of this product’s Lifetime Limited Warranty at
snapav.com/legal, or request a paper copy from
Customer Service at 866-424-4489.
Find other legal resources, such as regulatory notices and patent information,
at snapav.com/legal.
Technical Support
For chat and telephone, visit snp1.co/techsupport
Email: TechSupport@SnapOne.com. Visit
snp1.co/tc for discussions, instructional videos, news,
and more.
Copyright ©2022, Snap One, LLC. All rights reserved.
Snap One its respective logos are registered
trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home
Systems, LLC), in the
United States and/or other countries.
Dragonfly is also a registered trademark or trademark of Wirepath
Home Systems, LLC. Other names and brands may be claimed as the property of
their respective owners.
All specifications subject to change without notice.
221020 TW
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>