Leap Frog LF2936FHD 5.5 Inch Touch Screen WiFi Pan and Tilt Monitor User Guide

**Leap Frog LF2936FHD 5.5 Inch Touch Screen WiFi Pan and Tilt Monitor User Guide

**

Important Safety Instructions

The applied nameplate is located at the bottom of the Baby Unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the Baby Unit at a height above  6.5 feet (2 meters).

4. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water, for example, near to a bath, sink, swimming pool or shower.

7. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery in fire or a hot oven, mechanically crushing or cutting the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal.

8. Use only the power adapters included with this product. Incorrect power adapter polarity or voltage can seriously damage the product.
   Power adapter information: Baby Unit output: 5V DC 1A; VTech Telecommunications Ltd.; Model: VT05EUS05100 Parent Unit output: 5V DC 2A; V Tech Telecommunications Ltd.; Model: VT07EUS05200
   Rechargeable battery information: Zhuhai Great Power Energy Co., Ltd.; Lithium battery, 3.7V 5000mAh; Model: GSP806090-5Ah 3.7V-1S1P

9. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, underthe-table or cabinet outlet.

10. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

11. Unplug this product from the wall outlet before cleaning.
    Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

12. Do not modify the power adapters or replace with other adapters, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not install
    this product where the cords may be walked on or crimped.

14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or electricity supply provider.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat source.

18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

20. You should test the sound reception every time you turn on the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time.

23. The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach of children.

24. Children should be supervised to ensure that they do not play with the product.

25. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF (0oC) and 104oF (40oC).
2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.
4. Mishandling batteries can cause burn, fire or explosion hazards.
5. Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove warning label on the adapter cord.
6. Never place the Baby Unit(s) inside the baby’s crib or playpen. Never cover the Baby Unit(s) or Parent Unit with anything such as a towel or a blanket.
7. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)
This Leap Frog product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.

What’s Included

Download Leap Frog Baby Care+ App

Connect, Charge, and Power On the Baby Monitor

1. Connect the Baby Monitor
2. Charge the Parent Unit Battery

Notes:

• Before using the baby monitor for the first time, charge the Parent Unit battery for 12 hours. When the Parent Unit battery is fully charged, the battery icon becomes solid .
• The standby time varies depending on your actual usage time and the age of the battery

The battery icon on the screen indicates the battery status:

Power On or Off the Baby Monito

1. Slide the On/Off switch to ON to power on your Baby Unit.
2. The Parent Unit turns on automatically after connecting to the power socket, and the welcome screen appears. The green LINK LED light flashes. You can press and hold Power to turn it on or off.

Note:

• POWER LED Light is OFF by default.

Status Check

Once your Baby Unit and Parent Unit are powered on and connected, your Parent Unit displays video from the Baby Unit, and the LINK LED lights steadily.

Positioning the Baby Monitor

Note:
To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, mobile phones and computers.

Caution:
The default volume of your Parent Unit is level 3, and the maximum volume is level 5. If you experience a feedback noise from your baby monitor while positioning

• Make sure your Baby Unit and Parent Unit are more than 3 feet (1 meter) apart, OR
• Lower the volume of your Parent Unit.

Cable Management

Overview

Parent Unit

1. 3-level sound indicator
2. Power / LCD Off
3. Microphone
4. Arrow Keys
5. Menu / Select
6. Talk / Return
7. Battery LED indicator
8. Link LED indicator
9. Antenna
10. Power jack
11. RESET
12. Stand

Baby Unit

1. Light sensor
2. Camera
3. Infrared LEDs
4. Microphone
5. Night light
6. Night light control key
7. POWER LED Light
8. On / Off switch
9. Speaker
10. Antenna
11. Power jack
12. Wall mount holes
13. PAIR key

•  The Parent Unit and Baby Unit(s)provided are already paired.

Three Ways to Connect Your Baby Monitor

Direct mode
The Parent Unit and the Baby Unit are pre-paired and can connect to each other directly in Direct mode by default, which allows you to stream live video right out of the box. It is NOT recommended to continue using Direct Mode connection after initial installation.

Wi-Fi Router mode

You are required to set up your monitor in Router mode. Router mode uses your home Wi-Fi network to connect your baby monitor system. It enhances your local access by extending connection range.

With the LeapFrog mobile app, your Wi-Fi router (not included) also provides Internet connectivity to your baby monitor system, allowing you to control your Baby Unit wherever you are.

Auto mode

Auto mode should only be used when your Wi-Fi router is periodically turned off or the Wi-Fi connection is unstable. It works by automatically selecting the connection mode (Direct or Router) when connecting to the baby unit(s). For routers turned on with  good Wi-Fi connectivity, Router mode is the best selection. Mobile app access will not  beinterrupted in Auto mode.

Test the Location

If you plan to install your Baby Unit to a designated location, and will use your home Wi-Fi network to connect your video monitor, test whether your selected monitoring areas have good Wi-Fi signal strength.

Check the Parent Unit’s Wi-Fi signal strength by going to:

Adjust the direction and distance between your Baby Unit, Parent Unit, and Wi- Fi router until you have identified a suitable location with good connection.

Protect Your Privacy and Online Security

Leap Frog cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-recommended best practices to help keep your wireless connection private and your devices protected when online.

Ensure your wireless connection is secure

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-PSK with AES” setting in your router’s wireless security menu. Change default settings
• Change your wireless router’s default wireless network name (SSID) to something unique.
• Change default passwords to unique, strong passwords. A strong password:
  • Is at least 10 characters long.
  • Does not contain dictionary words or personal information.
  • Contains a mix of uppercase letters, lowercase letters, special characters and numbers. Keep your devices up to date
• Download security patches from manufacturers as soon as they become available. This will ensure you always have the latest security updates.
• If the feature is available, enable automatic updates for future releases. Disable Universal Plug and Play (UPnP) on your router
• UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network devices to open inbound ports without any intervention or approval from you. A virus or other malware program could use this function to compromise security for the entire network.

For more information on wireless connections and protecting your data, please review the following resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips – www.fcc.gov/consumers/guides/how-protectyourself-online.
2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet – www.us-cert.gov/ncas/tips/ST15-003.
3. Federal Trade Commission: Using IP Cameras Safely – https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.
4. Wi-Fi Alliance: Discover Wi-Fi Security – http://www.wi-fi.org/discover-wi-fi/security.

Pan and Tilt the Camera

You can swipe on the screen, use the arrow keys or the control panel on the parent unit to pan and tilt the camera.

Touch the screen to launch the overlay control panel, then tap .

• Tap the icons to move the camera upward, downward, leftward and rightward, or press and hold the icons to move continuously. OR
• Press the arrow keys on the parent unit to move the camera accordingly, or press and hold the arrow keys to move continuously.

The RBRC seal

The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal waste, which may be illegal in your area. VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

California Energy Commission battery charging testing mode

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the Parent Unit is paired to Baby Units, the CEC battery charging testing mode is activated while it is powered off and charging.

Disclaimer and Limitation of Liability

Leap Frog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook. Leap Frog and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect against data loss. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAN ICES-3 (B)/NMB-3(B)
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Warranty: Please visit our website at leapfrog.com for full details of the warranty provided in your country

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not ause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The Baby Unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8
in (20 cm) or more. The transmitter and antenna of the Parent Unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RF radiation exposure statement The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The Baby Unit should be installed and operated with a minimum distance of 8 in (20 cm) between the Baby Unit and all persons’ body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

References

• LeapFrog Customer Support | Help & Support For LeapFrog Products
• LeapFrog Customer Support | Help & Support For LeapFrog Products
• Before You Connect a New Computer to the Internet | CISA
• Security | Wi-Fi Alliance

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>