microlife IB NEB PRO EN-RU 4922 2 in 1 Professional Compressor Nebuliser User Manual

microlife IB NEB PRO EN-RU 4922 2 in 1 Professional Compressor Nebuliser

1. Piston compressor
2. Power lead
3. ON/OFF Switch
4. Air filter compartment
5. Nebuliser
   -A: Advanced treatment (position A)
   -B: Short treatment (position B)
6. Nasal washer
7. Air hose
8. Mouthpiece with valve
9. Nose piece
10. Adult face mask
11. Child face mask
12. Air filter
13. Filling the nebuliser
14. Assembling and usage of the nasal washer

Dear Customer,
This nebuliser is an aerosol therapy system suitable for domestic use. This device is used for the nebulisation of liquids and liquid medication (aerosols) and for the treatment of the upper and lower respiratory tract.
If you have any questions, problems or want to order spare parts please contact your local Microlife-Customer Service. Your dealer or pharmacy will be able to give you the address of the Microlife dealer in your country. Alter- natively, visit the internet at www.microlife.com where you will find a wealth of invaluable information on our products. Stay healthy – Microlife AG!

Explanation of Symbols

Electronic devices must be disposed of in accordance with the locally applicable regulations, not with domestic waste.

Read the instructions carefully before using this device.

Type BF applied part

Class II equipment

Catalogue number

Manufacturer

Serial number

ON

OFF

Protection against solid foreign objects and harmful effects due to the ingress of water

Conformity mark

Important Safety Instructions

• Follow instructions for use. This document provides important product operation and safety information regarding this device.
• Please read this document thoroughly before using the device and keep for future reference.
• This device may only be used for the purposes described in these instructions.
• The manufacturer cannot be held liable for damage caused by incorrect application.
• Do not operate the unit in presence of any anesthetic mixture inflammable with oxygen or nitrogen protoxide.
• This device should only be used with original accessories as shown in these instructions.
• Do not use this device if you think it is damaged or notice anything unusual.
• Never open this device.
• This device comprises sensitive components and must be treated with caution. Observe the storage and operating conditions described in the «Technical Specifications» section.
• Protect it from:
  • water and moisture
  • extreme temperatures
  • impact and dropping
  • contamination and dust
  • direct sunlight
  • heat and cold
• Comply with the safety regulations concerning the electrical devices and in particular:
  • Never touch the device with wet or moist hands.
  • Place the device on a stable and horizontal surface during its operation.
  • Do not pull the power cord or the device itself to unplug it from the power socket.
• Before plugging in the device, make sure that the electrical rating, shown on the rating plate on the bottom of the unit, corresponds to the mains rating.
• In case the power plug provided with the device does not fit your wall socket, contact qualified personnel for a replacement plug with that of a suitable one. In general, the use of adapters, simple or multiple, and/or extension cables is not recommended. If their use is indispensable, it is necessary to use types complying with safety regulations, paying attention that they do not exceed the maximum power limits, indicated on adapters and extension cables.
• Do not leave the unit plugged in when not in use; unplug the device from the wall socket when it is not in operation.
• The installation must be carried out according to the instructions of the manufacturer.
• An improper installation can cause damage to persons, animals or objects, for which the manufacturer cannot be held responsible.
• Do not replace the power lead of this device. In case of a power lead damage, contact a technical service center authorized by the manufacturer for its replacement.
• The power supply cord should always be fully unwound in order to prevent dangerous overheating.
• Before performing any maintenance or cleaning operation, turn off the device and disconnect the plug from the main supply.
• Only use the medication prescribed for you by your doctor and follow your doctor’s instructions with regard to dosage, duration and frequency of the therapy.
• Depending on the pathology, only use the treatment that is recommended by your doctor.
• Only use the nose piece if expressly indicated by your doctor, paying special attention NEVER to introduce the bifurcations into the nose, but only positioning them as close as possible.
• Check in the medicine instruction leaflet for possible contraindications for use with common aerosol therapy systems.
• Do not position the equipment so that it is difficult to operate the disconnection device.
• For greater hygienic safety, do not use the same accessories for more than one person.
• Never bend the nebuliser over 60°.

Preparation and Usage of this Device

Prior to using the device for the first time, we recommend cleaning it as described in the section «Cleaning and Disinfecting».

1. Assemble the nebuliser kit. Ensure that all parts are complete.
2. Fill the nebuliser with the inhalation solution as per your doctor’s instructions. Ensure that you do not exceed the maximum level.
3. Connect the nebuliser with the air hose 7 to the compressor 1 and plug the power lead 2 into the socket (230V 50 Hz AC).
4. To start the treatment, set ON/OFF switch 3 into the «I» position.
   • The mouthpiece gives you a better drug delivery to the lungs.
   • Choose between adult AT or child face mask AK and make sure that it encloses the mouth and nose area completely.
5. During inhalation, sit upright and relaxed at a table and not in an armchair, in order to avoid compressing your respiratory airways and impairing the treatment effectiveness. Do not lie down while inhaling. Stop inhalation if you feel unwell.
6. After completing the inhalation period recommended by your doctor, switch the ON/OFF switch 3 to position «O» to turn off the device and unplug it from the socket.
7. Empty the remaining medication from the nebuliser and clean the device as described in the section «Cleaning and Disinfecting».

NEB 2 in 1 – Aerosol therapy

The advanced «NEB 2 in 1» aerosol therapy allows effec-tive treatments of the medium and lower respiratory tract (asthma, chronic bronchitis, cystic fibrosis etc.). Advanced treatment
This treatment option allows the maximum amount of medication to be delivered thus reaching the respiratory capacity of each patient. The valve system optimally adapts the flow of medication during inhalation, reducing medication loss during exhalation.

Use the breath-enhanced valve system (synchronized with breathing) to optimize the therapeutic effects of the medication and to get the maximal benefit.

• Fill with medication AM and connect the nebuliser top to the nebuliser bottom by rotating it clockwise.
• Follow the usage steps as described in «Section 3.».
• Close the valve on the nebuliser top 5-A (position A) and use the mouthpiece with expiratory valve 8.

Short treatment
The therapeutic session will be reduced if the valve is open (position B) 5-B.
A synchronized nebulisation is not possible using this treatment option.

Nasal washer

The nasal washer 6 is a medical device suitable for cleaning nasal cavities. The nasal washer helps to moisturize the nasal mucosa and creates a micronized jet for the treatment of respiratory problems of the upper airways (allergic and nonallergic rhinitis, rhinosinusitis, nasal polyps etc.).

1. Remove the nasal washer cover AN-1 by rotating counter clockwise.
2. Fill the container of the nasal washer with isotonic solution AN-2. Ensure that you do not exceed the maximum level.
3. Close the cover tightly by rotating clockwise AN-3.
4. Connect the nasal washer with the air hose AN-4 to the compressor 1 and plug the power lead 2 into the socket (230V 50 Hz AC).
5. Close the non-treated nostril with your finger.
6. Position the nasal washer cover on nostril and inhale through the nose AN-5.
7. Switch the ON/OFF switch 3 to position «I» to turn on the device and place your finger over the aperture on the nasal washer to start the treatment AN-6.

We recommend changing from one nostril to the other every 10-20 seconds.
Children and people in need of care must be assisted for usage.
Only use with isotonic saline solution.

Cleaning and Disinfecting

Thoroughly clean all components to remove medication residuals and possible impurities after each treatment. Use a soft and dry cloth with non-abrasive cleaners to clean the compressor.

Make sure that the internal parts of the device are not in contact with liquids and that the power plug is disconnected.

Cleaning and disinfecting of the accessories
Follow carefully the cleaning and disinfecting instructions of the accessories as they are very important to the performance of the device and success of the therapy.

Before and after each treatment
Disassemble the nebuliser 5 by turning the top counter-clockwise and remove the medicine conduction cone. Wash the components of the disassembled nebuliser, the mouth-piece, nose piece and masks by using tap water; dip in boiling water for 5 minutes. Reassemble the nebuliser components and connect it to the air hose connector, switch the device on and let it work for 10-15 minutes.

Maintenance, Care, and Service

Order all spare parts from your dealer or pharmacist, or contact Microlife- Service (see foreword).

Replacement of the nebuliser
Replace the nebuliser 5 after a long period of inactivity, in cases where it shows deformities, breakage, or when the vaporiser head AM-A is obstructed by dry medicine, dust, etc. We recommend to replace the nebuliser after a period between 6 months and 1 year depending on the usage.

Only use original nebulisers!

Replacement of the air filter
In normal conditions of use, the air filter AL must be replaced approximately after 500 working hours or after each year. We recommend to periodically check the air filter (10-12 treatments) and if the filter shows a grey or brown colour or is wet, replace it. Extract the filter and replace it with a new one.

Malfunctions and Actions to take

The device cannot be switched on

• Ensure the power lead 2 is correctly plugged into the socket.
• Ensure the ON/OFF switch 3 is in the position «I». The nebuliser functions poorly or not at all
• Ensure the air hose 7 is correctly connected at both ends.
• Ensure the air hose is not squashed, bent, dirty or blocked. If necessary, replace with a new one.
• Ensure the nebuliser 5 is fully assembled and the colored vaporiser head AM-A is placed correctly and not obstructed.
• Ensure the required medication has been added.

Guarantee

This device is covered by a 5 year guarantee from the date of purchase. The guarantee is valid only on presenta-tion of the guarantee card completed by the dealer (see back) confirming date of purchase or the receipt.

• The guarantee covers only the compressor.
• The replaceable components like nebuliser, masks, mouth-piece, air hose, and filters are not included.
• Opening or altering the device invalidates the guarantee.
• The guarantee does not cover damage caused by improper handling, accidents or non-compliance with the operating instructions.

Technical Specifications

This device complies with the requirements of the Medical Device Directive 93/42/EEC.
Class II device as regards protection against electric shocks. Nebuliser, mouthpiece and masks are type BF applied parts.
The technical specifications may change without prior notice.
Date of production: first 8 digits of the LOT number of the device. First 4 digits: year / 5th and 6th digit: month / 7th and 8th digit: day of production.

References

• Hypertension and Fever Management - Microlife AG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>