dacor DHD-D0000CS-DA Duct Cover Kit Instruction Manual
- June 9, 2024
- dacor
Table of Contents
dacor DHD-D0000CS-DA Duct Cover Kit
Important Safety Instructions
APPROVED FOR RESIDENTIAL APPLIANCES FOR RESIDENTIAL
USE ONLY READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTALLATION GUIDE BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these instructions for the local electrical inspector’s
use.
INSTALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
WARNING Turn off power circuit at service panel and lock out panel before
installing this kit to the appliance.
Installation must comply with all local codes.
CAUTION Remove the carton carefully. Wear gloves to protect against sharp edges.
Tools and Parts
| DHD-D0000CS/DA | DHD-D0000CM/DA |
|---|---|
| DHD30U990CS/DA DHD36U990CS/DA DHD48U990CS/DA | DHD30U990CM/DA DHD36U990CM/DA |
DHD48U990CM/DA
Installation
General Dimensions
| A | 11 ¹⁵/₁₆” (30.4 cm) |
|---|---|
| B | 30” (76.2 cm) |
| C | 36 ¹⁵/₁₆” (93.9 cm) |
| D | 11 ¹⁵/₁₆” (30.4 cm) |
| E | 16 ¹/₂” (42 cm) |
| F | 16 ⁵/₁₆” (41.4 cm) |
| G | 16 ⁷/₁₆” (41.7 cm) |
Choose the duct cover configuration appropriate to the ducting length.
Place the duct cover lying on a flat surface and pull the medium cover outwards, finally slide the small cover to the outside too.
NOTE When using large and small duct covers together, assemble both pieces with 4 – 4.2 x 8 mm screws before finxing to the bracket.
Install Duct Cover Bracket
NOTE Secure Pro Canopy Hood to the wall before installing the Duct
Cover. See “Installation” section on the Hood Installation Manual.
-
Assemble the 3 pieces of the vent cover bracket with 2 – 4.2 x 8 mm screws provided using the Torx 20 adapter. The assembled bracket should be sized to fit inside the upper vent cover (X).
A. Vent cover bracket assembly
B. Upper vent cover
C. 2 – 4.2 x 8 mm screws
D. Centerline -
Position vent cover bracket on wall at the top of the ceiling, use a center line to align the support with the hood.
-
Mark the hole locations.
-
Drill ³/₈” (9.5 mm) holes for wall anchors and insert anchors flush with the wall.
Install Duct Cover
When using upper and lower vent covers, push lower covers down onto hood and
lift upper cover to ceiling and install with two mounting screws.
NOTE The upper vent cover may be reversed to hide slots.
-
Unistall and remove the motor if it is installed on the hood.
-
Place a tissue or soft cloth between duct covers to prevent scratching while installing.
-
Lift the duct cover over the hood and swivel toward the wall. Insert the hood base pins into the duct cover lower slots.
-
Once the four pins are already inserted, push the duct cover to fix them. Remove the tissue or soft cloth.
-
Carefully pull the top part of the extension upwards.
Screw the left and right sides of the extension to the mounting bracket with 2 -3.5 x 9.5 mm screws.
-
Replace the motor if removed.
NOTE The installation height above the counter top should be considered. Cutting and modification of one duct cover may be required to fit various ceiling heights. Any modifications should be done by a professional installer using suitable safety devices and observing the proper safety recommendations.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>