SONY VPLL-Z4107 Projection Lens Instruction Manual

: June 9, 2024
: Sony

Table of Contents

SONY VPLL-Z4107 Projection Lens Instruction Manual
Specifications
Replacing the Projection Lens
Adjusting the Projection Lens
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SONY VPLL-Z4107 Projection Lens Instruction Manual

SONY VPLL-Z4107 Projection Lens.jpg

Before operating the unit, please read this manual thoroughly and retain it for future reference.

This lens is designed for use with the Sony Projector.

For details concerning compatible models, consult with qualified Sony personnel.

Caution
Refer to the manual of the projector with which the lens is used for throw ratio and hazard distance.
If the projector becomes RG3 (Risk Group 3 as per IEC 62471-5) by the combination, the following warnings apply.

No direct exposure to the beam shall be permitted.
Operators shall control access to the beam within the hazard distance or install the product at a height that will prevent eye exposure within the hazard distance.

Attaching the lens may cause fire or injury to the person.
Users should request qualified Sony representative to attach the lens.

WARNING
Operation of this equipment in a residential environment could cause radio interference.

For the customers in Europe
This apparatus shall not be used in the residential area.

On condensation
If the room temperature where the projector is installed changes rapidly, or if the projector is moved suddenly from a cold to a warm place, condensation in the projector may occur. As the condensation may cause malfunction, be careful in adjusting temperature settings of the air conditioner. If condensation occurs, leave the projector turned on for about two hours before use.

Notes

Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.
SONY WILL NOT BE LIABLE FOR CLAIMS OF ANY KIND MADE BY USERS OF THIS UNIT OR MADE BY THIRD PARTIES.
SONY WILL NOT BE LIABLE FOR THE TERMINATION OR DISCONTINUATION OF ANY SERVICES RELATED TO THIS UNIT THAT MAY RESULT DUE TO CIRCUMSTANCES OF ANY KIND.

For the customers in the U.S.A.
SONY LIMITED WARRANTY – Please visit http://www.sony.com/psa/warranty for important information and complete terms and conditions of Sony’s limited warranty applicable to this product.

For the customers in Canada SONY LIMITED WARRANTY – Please visit http://www.sonybiz.ca/pro/lang/en/ca/article/resources-warranty for important information and complete terms and conditions of Sony’s limited warranty applicable to this product.

For the customers in Europe
Sony Professional Solutions Europe -Standard Warranty and Exceptions on Standard Warranty.
Please visit https://pro.sony/supportservices/primesupport /supportprofessional-solutions-europe-standardproduct- warranty for important information and complete terms and conditions.

For the customers in Korea SONY LIMITED WARRANTY – Please visit http://bpeng.sony.co.kr/handler/BPAS-Start for important information and complete terms and conditions of Sony’s limited warranty applicable to this product.

Supplied accessory

Operating Instructions (1)

Specifications

VPLL-Z4107
Electric focus/zoom, (when attaching to the projector),
Projected image size: 60″ to 600″ (1.52 m to 15.24 m)

Maximum external dimensions
(W × H × D):
158 × 143 × 266 mm
(6 7/32″ × 5 5/8″ × 10 15/32″)
Mass: Approx. 3.3 kg (7.2 lb)

Note

The values for mass and dimensions are approximate.

Replacing the Projection Lens

Notes

Be careful not to drop the projection lens.
Avoid touching the lens surface.
Lenses can be scratched easily. When handling lenses, always place them gently on a stable, level surface in a horizontal position.
Make sure to attach the supplied lens cap when you remove and store the lens. Not doing so may result in lens scratches.
Do not place any object in front of the lens that may block the light during projection.
If light is blocked, heat may damage the object or the lens of the unit (resulting in deformation, etc.). Use the picture muting function to suspend projection for a short while.
The illustration of VPL-FHZ120L is used for the explanations.

Removing

Return the projection lens to the center position. While the projector is turned on, press the LENS SHIFT button on the Remote Commander, then press the RESET button on it. The projection lens returns to the center position.
Note: The projection lens cannot be removed unless it has returned to the center position.
Turn off the projector, then unplug the AC power cord from the wall outlet.
Caution: When replacing the lens, your eyes may be damaged if a strong light accidentally gets into your eyes. Before replacing the lens, turn off the projector and then unplug the AC power cord.
Remove the lens cover. While sliding the LENS COVER RELEASE buttons inward, pull out the lens cover until it clicks into place.
While pressing the slide switch, move the lever up to the limit, and pull the lens straight out while firmly holding the lens not to drop it.
Attach the lens cover.
Hang the upper side of the lens cover on the top cover of the projector and press it until it clicks into place. Then, while sliding the LENS COVER RELEASE buttons inward, insert the lens cover.

Even when the lens is attached, you can attach/remove the lens cover in the same way.

Attaching

Turn off the projector, then unplug the AC power cord from the wall outlet. Caution: When replacing the lens, your eyes may be damaged if a strong light accidentally gets into your eyes. Before replacing the lens, turn off the projector and then unplug the AC power cord.
Remove the lens cover.
While sliding the LENS COVER RELEASE buttons inward, pull out the lens cover until it clicks into place.
Turn the contact substrate to the left facing the front of the lens and insert the lens to the end while firmly holding the lens not to drop it.
While pressing the slide switch, lower the lever until it clicks into place.
Attach the lens cover.